Cetacea ASTRO-XLW001-SFC Quick start guide

Brand
Cetacea
Model
ASTRO-XLW001-SFC
Type
Quick start guide

This manual is also suitable for

Technical Audio for the 21st Century Classroom
Quick Start Guide
Orbiter
System No.:
ORB-CMD-001
ORB-CMD-LR001
PRIOR TO OPERATION
Please allow two hours of charge prior
to fi rst use.
1. Connect the charger to the power connector on the Orbiter.
2. Green LED will begin fl ashing.
3. Allow for two hours of charge time prior to fi rst use or
when Green LED is glowing steady.
2
CONNECT ORBITER TO CHARGER
CHARGE UP ORBITER
TRANSMITTER
➊
➋
READ BEFORE
INSTALLING
For in-depth safety, installation,
and operational procedures, read or
download the Orbiter Owner’s Manual
at www.cetaceasound.com.
ORBITER™ SYSTEM CONTENTS
Orbiter Transmitter Orbiter Receiver
Receiver Power Supply
Transmitter Charger Lanyard Kit
Orbiter
R/C
Audio Cable (optional)
NOTE
The Orbiter has built-in overcharge protection.
Once fully charged, the Green LED will cycle
between charge (steady) and discharge (blinking).
INSTALLER NOTES
No tools are required to set up the
Orbiter other than to run cable as
needed. Clips, hangers, and hooks are
recommended for long cable runs.
Orbiter
R/C
1. Connect 3.5 mm speaker
cable to ORBITER OUTPUT
connector and amplifi er/
speaker INPUT.
2. Connect the power supply
to the receiver POWER
connector and AC source.
3. Green LED will illuminate
to indicate receiver is ON.
15V DC
PWR
VAR
LINE
1
2
3
ORBITER
EXT. ANT.
INPUTS
OUTPUTS
POSITION RECEIVER ON A FLAT SURFACE NEAR AN AC SOURCE
SET UP AND CONNECT
RECEIVER
➊
➋
CONTROLLING FEEDBACK
When operating the Orbiter for the fi rst
time, step away from the speaker and be
ready to adjust volume down as needed.
Have a second person help determine
appropriate loudness by listening from
the audience location.
OPERATE THE ORBITER
TRANSMITTER
REMOVE ORBITER FROM CHARGER PRIOR TO USE
3. Amber LED will illuminate on the receiver while connected.
4. Set appropriate volume with VOLUME CONTROL button.
1. Click MASTER CONTROL once for ON.
Click again to cycle between ON and MUTE. To
turn OFF, push and hold MASTER CONTROL for 4
seconds, then release.
2. Green LED will illuminate on the transmitter while ON.
➊
➍
R/C
Orbiter
R/C
Astronaut Speaker (not included)
NOTE
The Orbiter will not connect to the receiver while charging. Once
charged, disconnect charger and operate pendant as normal.
Orbiter Transmitter
FRONT
BACK
Orbiter Receiver
EXTERNAL
ANTENNAE
NOTE:
Optional
feature
DC POWER
CONNECTOR
INPUTS (1, 2, 3)
Stereo/mono source
connections
LINE OUTPUT
Signal output for
INPUTS (1, 2, 3) to
amplifi er/speaker
VARIABLE OUTPUT
NOTE:
Future feature set
and is currently disabled
ORBITER OUTPUT
Signal output for Orbiter
microphone to amplifi er
/speaker
WIRELESS
CONNECTION
Amber LED
POWER
Green LED
MASTER CONTROL
ON/OFF/MUTE
VOLUME
CONTROL
STATUS INDICATOR
Green LED
FRONT BACK
REFERENCE IMAGES
© 2014 Cetacea Sound Corp. All rights reserved. Orbiter™ is a trademark of Cetacea Sound Corp. 1(800) 556-1922 [email protected] www.cetaceasound.com All audio products are proudly made in the U.S.A. (5/14) 201207-005
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Cetacea ASTRO-XLW001-SFC Quick start guide

Brand
Cetacea
Model
ASTRO-XLW001-SFC
Type
Quick start guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents