Legrand DLM Configuration App User guide

Wattstopper

®

DLM Configuration App

User’s Guide

28653 Rev. 2 08/2019

DLM Conguration App

Country of Origin: Made in the USA

FEATURES AND OPERATION OVERVIEW

OVERVIEW

The Wireless Digital Lighting Management (DLM) Conguration app from Legrand is supported on

iOS

®

and Android

®

and allows users (electrical contractors, installers, or technicians) to wirelessly

scan for, pair together, and congure Wattstopper Wireless DLM devices and room networks. From

the convenience of a smart phone or tablet and using Bluetooth

®

low energy technology, the app

creates a secure environment to easily establish and manage DLM wireless rooms across a project.

Code compliant rooms are now easier to set up and more secure than ever before, giving end-users

comfort that their wireless devices and rooms are protected in a wireless environment. Replacing

the traditional LMCT-100 infrared remote, no other hardware or tools are needed for commissioning

wireless DLM devices.

Description Specication

DLM Cong App 1.1.1 or newer

Apple iOS Compatibility iOS10 or later, recommended iOS11

Android Compatibility Android OS 4.4 (KitKat) or later; Recommended Android OS 7 (Nougat)

Wireless DLM Device Firmware Version 10.14 or newer

Bluetooth® 4.2 and higher

SYSTEM REQUIREMENTS AND COMPATIBILITY

• Compatibility: iOS and Android tablets and phones (tablets are preferred)

• Establish and manage wireless DLM rooms, networks and sites

• Congure wireless DLM rooms for energy code compliance

• Enable fast setup and maintenance

• “Quick Scan” for fast DLM room pairing

• Protected bi-directional Bluetooth

®

low energy technology communication for data upload and download

• User-friendly navigation controls and context menus

• Cloud Authentication: Role-based user and site authentication

• Ongoing AES Encryption: Communication between devices is protected by AES128 symmetric key encryption

• Over the Air (OTA) Updateable Firmware: Allows the system to address future cyber security threats

• Device Validation: Trusted hardware chips prevent any outside devices from being able to connect to the lighting control network

• Zero Touch Provisioning: Preloaded digital identity and security proles on each device make the system automatically secure

• Lighting Network Isolation: Lighting control system can be independent of all other building networks

2

TABLE OF CONTENTS

GETTING STARTED

App Overview.............................................................................4

Creating An Account..................................................................5

Dashboard Overview.................................................................7

CREATING SITES and WIRELESS ROOMS

Overview..................................................................................10

Sites.........................................................................................10

Create A Site.............................................................11

Sites Dashboard Overview........................................12

Areas Overview.........................................................13

Creating Areas Within A Site....................................14

Split Rooms...............................................................16

Waking Up Devices...................................................17

Networks................................................................................18

Discovering Networks and Devices..........................18

Creating A New Network: Networks View...............19

Creating A New Network: Room Controller...............20

Adding Devices.........................................................22

Decommissioning A Site and Clearing App Data.....23

Room Controller Settings.........................................................24

Firmware Update.......................................................26

Daylighting Calibration..............................................28

Parameter Settings...................................................31

Switch and Sensor Properties..................................36

Scenes.....................................................................................38

Scenes Overview.......................................................37

Default Scenes..........................................................39

Creating Scenes.......................................................41

Scene Categories.....................................................43

Scene Actions.............................................45

Editing Scenes...........................................48

Site Synchronization................................................................50

Site Information........................................................................51

QUICK PAIR

Quick Pair Process..................................................................53

SETTINGS and NAVIGATION

Navigation Menu......................................................................57

Navigation Icons......................................................................59

3

GETTING STARTED

4

THE DLM CONFIG APP OVERVIEW

5

CREATING AN ACCOUNT

1. The DLM Conguration App is accessible by download

through the Apple App Store or Google Play for Android.

Search for “DLM Conguration” by Legrand. Install and

launch the app on your smart phone or tablet. Press the

Create New Account option. (Requires Internet access)

2. Enter the data for all the elds. Press Create Account when

nished.

• Valid email address

• Valid password (must contain at least 8 characters, 1

uppercase letter, 1 number)

• Contact name(s)

• Mobile phone number

Press Create Account to complete.

Install the app and create an account which will start the authorization process.

THE ACCOUNT PROCESS

This is also known as a Basic Account which allows for

immediate simple quick pairing. It is recommended to

obtain an authorized account.

This is also known as an Authorized Account which is a

basic account that has been approved from Legrand. With an

authorized account, the user will have enhanced access to

device parameters, scenes, and SoO.

- OR -

CONGRATULATIONS! Your account has been submitted for authorization. You can call a Wattstopper representative at

1.888.538.6070 to inquire about your authorization status. While you are awaiting authorization, your dashboard will reect your

account status as:

• Create a DLM wireless room network

• Congure Room Controller and add to the room network

• Congure devices

• Quick pair by dragging and dropping device tiles to the

Room Controller

• Establish site(s)

• Set up areas and rooms through a tree structure

• Assign devices to areas and rooms

• Set device parameters for Room Controllers, keypads, and

sensors

• Create, manage and assign scenes

• All site information is secured and uploaded to the cloud

UNAUTHORIZED ACCOUNT CAPABILITIES AUTHORIZED ACCOUNT CAPABILITIES

6

The DLM Cong App has been created to provide a simple and intuitive user experience. At any level within the app, help is just a tap

away providing context-specic guides of denitions, options, and instruction to help you navigate through available actions.

HELP OVERVIEW

1. Tap the question mark icon in the top right corner for

context-specic help on every level throughout the app.

2. Upon entry, users are presented with pop-ups. Swipe side

to side to learn more about context specic information at the

current level. To exit, tap Get Started, Dismiss, or Got It at the

bottom depending on which level you are on.

7

DASHBOARD OVERVIEW

The Dashboard provides quick access to buttons status information, historical view, and a calendar view of schedules.

MENU

Tap the “menu” button (three lines) to access the pop-up

menu containing account information, language, themes

and colors, and “About” details - see next page for details

QUICK PAIR

Quick pair allows for easy

set up and pairing of

equipment within the room

to the network

HELP

Tap to access context specic

help on every level of the app

SITES

Select to view, create, and modify multiple

wireless DLM sites - Veried account feature

BLUETOOTH

®

LOW ENERGY

TECHNOLOGY

CONNECTIONS

View active Bluetooth low energy

technology connections

RECENT SITES

After sites have been established

and used, they will appear in this

area for quick access. Each site tile

will contain identifying information

associated with the site that has

been entered into the site eld

INFORMATION

Displays the user’s status showing

if account info is complete and if

it is a veried account. Veried (or

authorized) accounts have access to

customized functionality

NOTE: Although the same functionality exists between

tablets and phones, the following screen layouts may differ

depending on the device used. It is recommended to use

tablets for optimal viewing. (Tablet screenshots shown

throughout user guide)

8

DASHBOARD POP-OUT OVERVIEW

DASHBOARD

Return to the main dashboard

CONFIGURATION

Menu options

SETTINGS

Menu options

SITE

Link to current site’s location dashboard

NOTIFICATION CENTER

Displays notications from the app

ALL SITES

Link to all sites

ACCOUNT

View account info

LANGUAGE

Select default language

THEMES

Set theme and font size for optimal viewing

ABOUT

View app info, set notications

QUICK PAIR

Link to networks for quick pairing

Accessed by the three lines on the main dashboard, the pop-up menu contains quick access to sites, account information and provides ability to

change language, themes and colors.

9

CREATING SITES and

WIRELESS ROOMS

10

The optimal and recommended way to set up your wireless system is through sites. Sites allows for viewing of all available sites and

the creation of new sites. Site details can also be viewed and edited. Recently visited sites are accessible directly from the home

dashboard. By setting the structure for each site through areas and rooms, you can connect devices directly to those rooms for

organization, edit device parameters and sequence of operations. This diagram shows the steps you will take to establish wireless

DLM room networks through the sites option.

SITES AND WIRELESS ROOM OVERVIEW

SITES

Establish a site with a name and

location. Add contact information and

code compliance for a complete site

prole.

Repeat for multiple sites.

Within the dashboard, tap the sites

icon to view and edit the site structure

through areas and rooms.

SET UP AREAS AND ROOMS

Structure the site by establishing areas

and rooms in a tree structure. This

allows for zone control of devices and

scenes.

Obtain more detailed information like

light load average and room status

through the room view. Toggle between

device and room view by tapping the

desired icon.

ASSIGN DEVICES

Assign devices to established areas

and create rooms. View awake status

and connectivity strength through

device tiles.

CREATE ROOM NETWORK

Create a secured room network by

pairing devices to a room controller.

Changes are automatically updated to the

Legrand secure cloud.

SET PARAMETERS and

SEQUENCE of OPERATIONS

(SoO)

Set parameters of the devices through the

room controller. Some parameter options

include:

• Trim Levels

• Occupancy Delays

• Vacancy Timeouts

1 2

43

5

11

CREATE A SITE

1. From the home dashboard, all recent sites will be visible at the

bottom. If you have not yet created sites, Recent Sites will be

blank. To collapse the view of recent sites, tap the arrow. To add

a site, tap the Sites tile to continue.

3. Fill in the elds for the new site. The name, city, and state

are required to create a site. The other information is helpful to

create a complete prole but is not required.

Note: Once a site is created, it cannot be deleted, only edited

through the app. The site owner can call the service center to

have a site removed from the account. 1.888.538.6070

2. After entering Sites, tap an established site tile for further

editing. Or to add a new site, tap Create Site from the “+” round

blue button in the right hand, lower corner.

4. Identify the site with a Code Compliance option for reference.

Choose from Title 24 (2016), Ashrae 90.1 (2013), IECC (2015) or

none. Tap Create when nished to complete the site set up. Use

parameters and scenes to create a code compliant site.

Repeat this process for each site creation. The most recent sites

will now be located under the main dashboard for convenience.

Tap on the site tile from the sites level to access the sites

dashboard.

12

SITES DASHBOARD OVERVIEW

Once a site is selected, the Site Dashboard allows you to view the Site Structure, Network, Scenes, and more information about the

selected site. To navigate through the Site Dashboard, use the navigation bar at the bottom of the page to access the other options.

SITE STRUCTURE

Edit the areas and rooms within the site

and view additional information about a

specic site

CLOUD SYNCHRONIZATION

Notications are displayed when new actions that

require cloud synchronization are made. View each

item’s cloud upload status. Items that have been

uploaded to the cloud can be removed from the list.

ROOM NETWORK VIEW

View a list of all established room networks.

Also provides an easy view of device count

assigned to the wireless room network.

SCENES

Create, manage and edit scenes within sites whether through the default scenes or customized ones you create.

Add multiple actions to scenes and assign to desired devices. Organize scenes into custom categories.

SITE INFORMATION

View established account information of

address, contacts, codes, and details. Edit

by tapping the pencil icon.

AREAS

Manage areas and

rooms within the

building. Edit names,

add areas and

remove areas

SITE ROOT

Site top level (root) where areas and

rooms are displayed in tree structure

13

Main Building

COLLAPSE ALL

Site

Area / Room

Area 1

Sub Room 1

Sub Room 2

Sub Room 3

Edit Name

Add Area

Split Room

Delete

View additional information about a specic location such as devices, loads, and scenes by tapping the area name which accesses

the room view. Toggle between the room and device view by tapping the desired icon at the top right.

ROOM VIEW DEVICE VIEW

DEVICE AND ROOM VIEWS

Structuring the site through areas and rooms is the optimal organization method for devices. By preparing your site under this format,

you can efficiently assign devices and control lighting parameters. This overview will help you understand the tree structure of areas in

the DLM Config app.

Under the root building, add areas according to desired site set up. You can add more areas under the original area. Once you have

added hardware to an area, it becomes a room and no more areas can be added under it. An area has the ability to become a split

room where you can divide the area into sub-rooms with individualized control. The original room now becomes an area again once

it hosts sub rooms. NOTE: You cannot add areas below a sub room. However, you can nest an area for multiple layers.

ROOT BUILDING

SUB-ROOM

Created from the Split

Room option, these

rooms can divide a

bigger area into smaller

zones or rooms. A room

that is split turns back

into an area

SPLIT ROOM

This option

appears when a

device has been

added to an area

and a room has

been formed.

Create sub-rooms

within an area for

tighter control.

ROOM

An area that has added

hardware. Once sub-

rooms are added, it

becomes an area again.

AREA

SITE

AREAS OVERVIEW

Device ViewRoom View

14

CREATING AREAS WITHIN A SITE

1. Begin by establishing the name of your root building by

tapping the three dots and select Edit Name.

3. Under the root building level, tap the three dots and select

Add Area +.

2. Type the desired name and press the check mark to conrm.

4. Name the new area and press OK to conrm. Repeat adding

desired areas under the root building.

15

CREATING AREAS WITHIN A SITE (continued)

5. You can also add an area under an area. Tap the ellipses

under the desired area and tap Add Area. You can add multiple

areas under an area.

6. Name the area and press OK to conrm.

1. To delete an area, tap the three dots on the area you wish to

delete and select delete.

2. Tap OK to conrm area deletion.

DELETING AREAS WITHIN A SITE

16

SPLIT ROOMS

Once an area has added devices, you are able to split the area up into rooms. This provides focused management over a smaller

area or zone. These new rooms are indicated by the room symbol . See page 17 on how to wake devices before adding them to a

room. See page 22 on how to add devices to a room. This needs to be done before splitting an area into rooms.

NOTE: The room that was split becomes an area once again in the organizational tree.

1. Tap the three dots at the area level you want to split and

select Split Room .

2. Name the room by tapping New Room 1 and editing the name.

3. Add another sub room by tapping the symbol underneath

the rst room. Edit the name and continue adding sub rooms as

necessary. To delete a room, tap the symbol to the right of the

room.

17

1. Room Controller

Wake up room controllers by pushing the cong button once as

indicated.

NOTE: The BLE connection to a room controller remains on

while it is on the default network. It will turn off after being paired

to a room.

4. Factory Default

To reset the controller or any device to factory default, press the

conguration button quickly 10xs.

CONFIG

BUTTON

CONFIG

BUTTON

WAKING UP DEVICES

3. Sensors

Wake up sensors by pushing the cong button once, as

indicated.

2. Wireless Dimming Wall Switch

Remove switch plate and with a pen point or small screwdriver,

push the conguration button one time to awake.

In preparation to adding devices and establishing a network, battery operated devices must be awake. It may be necessary to wake

up the devices if they are asleep. To wake up devices by pushing the cong button once. This powers up the device for 5 minutes

which gives you enough time to pair the device through the app. Follow these instructions on how to wake up room controllers,

sensors, and wall switches. NOTE: Wake up all devices within arms reach before installation and if needed, other installed devices

via ladder.

18

2. At a quick glance, you can see the number of devices

assigned to each network. Select All Devices to see all active

device tiles or select the desired network to view its device tiles.

3. All devices across all networks at the site are shown in the All

Devices view. You may need to wake up devices (See page 17).

1. The app will start to scan for available networks and display

them. Filter for secured and unsecured networks. Choose the

network and tap to see devices. If it shows there are no networks

within range, tap Show Unsecured Networks or Add Network

at the bottom. Select the desired network to view.

Tap to access Networks. This is a list of all the Networks that are locked to the site and currently seen within range, or if

connected, from the cloud. You can start and stop scanning by pressing the Scan button in the upper left. Selecting a Network will

allow you to see what is on the network and adjust device parameters (if permissions allow). The Default Network will be visible if

there are devices in range that are not currently assigned to a specic network. To see all devices regardless of which network they

are on, select All Devices. All devices that are paired to this site are visible through networks. To view unsecured networks alongside

your secured networks, select “Unsecured” from the lter menu.

NETWORKS

DISCOVERING NETWORKS AND DEVICES

4. Search for devices in various ways. Under Filters, choose to

view devices or networks under certain categories.

19

5. You can also arrange device tiles alphabetically ascending/

descending, by signal, MAC address, or network. To search for

a specic MAC address, enter the address in the upper right

search eld.

DISCOVERING NETWORKS AND DEVICES (continued)

1. On the Networks page, tap the Add Network + button in the

bottom right of the screen. Tap Create new network from the

options.

2. Select the room controller which will support the network.

CREATING A NEW NETWORK THROUGH THE NETWORKS VIEW

There are two ways to create a new network: 1. Through the Networks view and 2. Through a Room Controller (see pages 20-21).

Creating through the Networks view is the suggested method.

20

3. Select the device(s) you want to add to the network by

tapping the white box of the device tile. When chosen, the box is

checked in green. Once all the devices have been added, select

the green circle check-mark to add the devices to the network.

This can take a couple of minutes.

4. A status screen will show the initiating process and show

pairing devices. After devices have been paired, the network will

reboot and verify that all devices have been paired.

CREATING A NEW NETWORK THROUGH THE NETWORKS VIEW (continued)

CREATING A NEW NETWORK THROUGH A ROOM CONTROLLER

1. Creating a new network is handled from any room controller

in the Network view. Select Default Network and then select the

room controller which will support the network.

2. Under Network Management, tap Create New Network.

Page is loading ...

Legrand DLM Configuration App User guide

Related papers

Other documents