Trex WBFGATEDBLKIT Installation guide

Brand: Trex

Model: WBFGATEDBLKIT

Type: Installation guide

This manual is also suitable for

TREX SECLUSIONS DOUBLE

GATE INSTALLATION GUIDE

Seclusions 5x5 fence post

Seclusions fence gate panels (2)

Steel post stiffener (2)

Seclusions fence hinge (4)

Seclusions fence latch

Seclusions striker

Seclusions gate handle (2)

1-1/2” self-drilling screws (40)

1” self-drilling screws (16)

TOOLS NEEDED

SECLUSIONS DOUBLE GATE COMPONENTS

BEFORE YOU BEGIN

» Read all instructions before installation.

» Follow Trex Seclusions Installation Instructions to lay out fence and dig holes.

Slide a Steel Post Stiffener into each hinge post.

Open side of insert should face away from gate

opening.

Set posts into post holes that are 30” deep (or to

frost line) by 12” wide.

Opening (measuring from inside edge of post to

inside edge of post) for Trex Double Gate using

(2) large gate panels should be 130-1/2”. Inside

faces should be plumb and parallel.

Note: Due to concrete cure times, set the gate posts

2-3 days before gate is installed.

Note: If Hinge Post is not connected to a fence panel,

it may be necessary to use a Heavy Steel Post

Stiffener or to fill the post with concrete for additional

strength.

Check for level.

130-1/2”

30”

12”

Opening for double gate using two small panels

should be 91-1/2”. For custom size double gates

the opening is 2-3/4” larger than the combined

panel widths.



BACK SIDE OF B2

Active panel

Non-active panel

Seclusions drop rod assembly

STEP 1: SET THE GATE POSTS

2” self-drilling screws (6)

TREX SECLUSIONS DOUBLE

GATE INSTALLATION GUIDE

OPTIONAL ANTI-SAG CABLE KIT

ANTI-SAG CABLE KIT COMPONENTS

ATTACHING THE CABLE KIT

Black vinyl wrapped steel cable

Cable clamp (2)

‘S’ hook

‘D’ rings (2)

1” Self-drilling screws (2)

Turnbuckle

D E

Attach upper ‘D’ ring to the “hinge side” of the

panel, 5-1/2” down from top of gate and 1-3/4”

from the edge of gate (to hit the inner steel

frame), using (1) self-drilling screw.

Attach lower ‘D’ ring to the “latch side” of the

panel, 2” up from bottom of gate and 1-3/4” from

the edge of gate, using (1) self-drilling screw.

Lengthen the turnbuckle as long as possible

before proceeding by twisting the center ring.

Attach the turnbuckle to the upper “D” ring using

the “S” hook.

HINGE SIDE LATCH SIDE

Loop one end of the cable through the lower eye

bolt of the turnbuckle. Attach a cable clamp and

tighten nuts as tight as possible.

Loop the other end of the cable through the lower

“D” ring and attach the other cable clamp. Pull

the cable as tight as possible before tightening

the nuts.

Remove any slack by tightening the turnbuckle,

twisting the center ring of the turnbuckle.

Note: To make installation easier, prop the gate to the

desired level using a block of wood under the latch

side edge of the gate panel.

For large gate panels, it may be neccssary to use an anti-sag cable to eliminate the sag of a gate panel. Anti-sag cable

kits can be purchased through your local Trex Distributor.

TREX SECLUSIONS DOUBLE

GATE INSTALLATION GUIDE

STEP 2: INSTALL THE GATE PANEL

Note: Install hinges on the side of the gate that you want the gate to swing toward.

6”

STEP 3: ATTACH THE LATCH AND HANDLES

Gate

swing

Catch

Swing direction

6”

Repeat the process to hang the other gate panel.

Attach the hinges to the gate panel approximately 6” from

the top and bottom of the gate using a 3/8” nut driver and

the (4) 1-1/2” supplied self-drilling screws. Pre-drilling with

a 3/16” drill bit will make installation easier.

Place the gate panel in the opening. Adjust the gate to be

level and to the desired height by placing blocks under gate

panel. Allow ample clearance for full swing of gate.

Using (4) 1-1/2” supplied self-drilling screws, attach each

hinge to the steel inserted gate post. Pre-drilling with a

3/16” drill bit will ease installation.

Open the panel and attach the inside corner of the bracket

to the gate post.

Attach the latch to the non-active panel approximately 36”

from the ground using (6) 1-1/2” supplied self-drilling

screws. The catch is to be placed in the direction of the gate

swing. The catch may face up or down depending on the

direction of gate swing.

Gate

swing

Catch

Using the (4) 1-1/2” supplied self-drilling screws, attach the

striker to the active gate panel, lining the striker rod up with

the catch on the post latch.

Attach gate handles to the active gate panel, using (2) 1”

supplied self-drilling screws. Handles should be attached

1-3/4” from the edge of the gate panel. The height must

be staggered front and back as shown.

Adjust hinges using the method described in Step 5 to

create an even 7/8” gap between the panels and so the tops

of the panels are even.

Swing direction

TOOLS NEEDED

SECLUSIONS DOUBLE GATE COMPONENTS

STEP 4: MOUNT THE DROP ROD TO THE NON-ACTIVE PANEL

STEP 5: MAKE ANY FINAL ADJUSTMENTS TO THE GATE HINGES AS NEEDED

Attach the drop rod brackets to the back side of

the non-active gate panel. Reverse the drop rod

brackets depending on which side of the gate the

drop rod is to be mounted.

Measuring from the horizontal tab (see below),

attach the lower bracket 3” from the bottom of

the gate panel using (3) 2” self-drilling screws on

the inside edge of the gate panel and (1) 1”

self-drilling screw on the face of the gate panel.

Repeat this process for the upper bracket,

attaching it 14” from the bottom of the panel.

Attach the drop rod hanger 24” from the bottom

of the gate panel and 2” to the center of the

screw holes from the edge of the gate panel.

Mark the location on the ground where the drop

hits. If your gate is over a concrete pad, drill an

8” deep hole using a 3/4” masonry bit for the

drop rod to slide into when the gate is closed.

For gates over dirt, dig a hole 8” wide x 18” deep

below the drop rod, ﬁll it with concrete, and

insert an 8” long 3/4” pvc pipe in the concrete for

the drop rod to slide into after the concrete has

cured.

To adjust a sagging gate, or to shift panel in the opening, loosen the hinge nuts with an 11/16” wrench.

Loosen or tighten the nuts in the direction shown below. Lift or push panel to slide the hinge.

Retighten the hinge nuts.

24”

14”

3”

2”

Top

Hinge

Bottom

Hinge

Shift panel left

Top

Hinge

Bottom

Hinge

Shift panel right

Top

Hinge

Bottom

Hinge

Raise latch side

Top

Hinge

Bottom

Hinge

Lower latch side

1-3/4”

TREX SECLUSIONS DOUBLE

GATE INSTALLATION GUIDE

Due to weather and temperature changes, periodic hinge adjustment may be necessary to assure proper latch

connection.

Trex WBFGATEDBLKIT Installation guide

Brand: Trex

Model: WBFGATEDBLKIT

Type: Installation guide

This manual is also suitable for

Download PDF

report

Trex WBFGATEDBLKIT Installation guide

This manual is also suitable for

Trex WBFGATEDBLKIT Installation guide

Related papers

Other documents