Episode EA-MINI-3D-35 User guide

Brand: Episode

Model: EA-MINI-3D-35

Type: User guide

This manual is also suitable for

EA-MINI-2D-35

EA-MINI-2D-35 EA-MINI-3D-35

IR Command Learning Procedure

Introduction

EPISODE

EA-MINI amplifiers feature optional IR Learning Mode, which allows control of the amplifier using

the remote for a display or any other remote on a job. After completing the learning procedure, the same

buttons for power toggle, volume up, volume down, mute toggle, and input toggle on the selected remote

will also control these settings for the amplifier.

Procedure Overview

To complete IR Learning, an IR Receiver must be connected. Set up the amplifier as shown below and select

the remote that will be used for control. Then, go to the second page of the guide (flip over) and complete

the learning procedure. Note the DIP switch locations and positions before attempting the procedure.

Tips & Troubleshooting

• Make sure the source remote contains a fresh battery.

• Use only factory remotes for IR learning. A universal or programmable remote may add data to the

command that makes it unreadable by the amplifier for Learning mode. They may be used for operation

after setup.

• If commands aren’t being received correctly, try relocating the IR receiver. Interference from CFL lighting,

plasma or LED television screens, or IR from other equipment may cause issues.

• IR learning may be stopped after any command. Wait 20 seconds for Learning mode to time out. The

LED will change from flashing BLUE to solid PINK for 2 seconds, and then return to solid BLUE to indicate

RUN mode. You may unplug the IR receiver during the time out to avoid interference. Do not return the

dip switch to Run Mode before time out or the memory will be cleared.

• The same button on the remote cannot control more than one amplifier command at a time.

• If a particular command does not have a corresponding button on the remote, any other unused button

may be substituted. For example, source remotes may not have an “input toggle” button or function.

Instead, program an unused button for input switching and make note of it for the end user.

• IR learning mode will deactivate after 20 seconds of inactivity (no commands received). If IR learning

mode deactivates before learning is complete, reset the amplifier (set DIP switch 2 UP to the RUN and

press master reset while amplifier is ON) and then start the IR Learning procedure again. Any commands

learned before will be erased.

READ ALL OF THIS SIDE FIRST - Page 1 of 2

Pag e 1/2

R+ R- L+ L-

DIGITAL IN

SUB OUTANALOG IN

RIGHT

1 2 3 4 5

IR IN

IR OUT

+5V GND

RESET

SPEAKER OUTPUTS

STATUS

LEFT

SWITCHES

100-240V~50/60Hz 1.6A

1 2

CONTROL

DOWN

RECEIVER

RUN

LEARN

MONO

STEREO

FULL

HP 60Hz

IN 1

IN 2

SWITCH POSITION

1 2 3 4 5

SWITCHES

1 2 3 4 5

SWITCHES

Status LED provides IR Learning Feedback

DIP Switch 2 DOWN for IR LEARNING MODE

DIP SWITCH 1 DOWN FOR IR RECEIVER POWER

IR RECEIVER

(Not Included)

Plugged into

IR IN Port

www.SnapAV.com | Support: 866.838.5052

EA-MINI-2D-35 EA-MINI-3D-35

IR Command Learning Procedure

Command Learning Order (Must be learned in this order!) Tools Required

*It is not necessary to wait for the pictured sequence of short blue ﬂashes before entering each

code. These ﬂashes only indicate which code is being learned.

Learning Errors

Command Description

1. Power Toggle ( ) Turn ampliﬁer power on and off.

2. Volume Up (V+) Turn volume up (louder).

3. Volume Down (V-) Turn volume down (quieter).

4. Mute Toggle ( ) Toggle mute mode (no volume) on and off.

5. Input Toggle ( ) Switch between inputs 1 and 2.

A red LED indicates a learning error. After an error, repeat the current command until it learns correctly. See the

example below:

Page 2/2

LED:

Return DIP switch 2 to RUN (UP) using the tweaker. Learning Complete.

Flip DIP switch 2 DOWN with the tweaker to enter IR Learning Mode.

PINKBLUE

RUN Mode ... DIP Switch 2: LEARN (DOWN) Learning Mode, awaiting Command ...

Re-enter command

PINK

LED:

Ok. Power Learned

Press Press

BLUE BLUE

LED:

PINK Ok. V+ Learned

Press Press

BLUE BLUE

V+ V+

Press Press

LED:

V- V-

PINK

Ok. V- Learned

BLUE BLUE

1. Learn Power Toggle ( )

2. Learn Volume Up ( V+ )

3. Learn Volume Down ( V- )

4. Learn Mute Toggle ( )

Press Press

LED:

PINKBLUE BLUE

Ok. Mute Learned

PINK

BLUE BLUE

Ok. Input Toggle Learned

Press Press

LED:

Tweaker Screwdriver

(required tool for DIP Switch)

Instructions

131017-1630

5. Learn Input Toggle ( )

Episode EA-MINI-3D-35 User guide

Brand: Episode

Model: EA-MINI-3D-35

Type: User guide

This manual is also suitable for

EA-MINI-2D-35

Download PDF

report

Episode EA-MINI-3D-35 User guide

This manual is also suitable for

Episode EA-MINI-3D-35 User guide

Related papers

Other documents