Binary B-500-MTRX-230-16x16 Installation guide

Brand: Binary

Model: B-500-MTRX-230-16x16

Category: Supplementary music equipment

Type: Installation guide

This manual is also suitable for

B-500-MTRX-230-8x8

Binary™ HDMI Matrix Switcher

with HDMI and HDBaseT Outputs

Installation Manual

B-500-MTRX-230-8x8 Installation Manual

Pg. 2

™

1. Important Safety Instructions

 Toreducetheriskofreorelectricshock,donotexposethisapparatustorainormoisture.Donot

removecover.Nouserserviceablepartsinside.Referservicingtoqualiedservicepersonnel.

Thelightningashwitharrowheadsymbol,withinanequilateral

triangle, is intended to alert the user to the presence of

un-insulateddangerousvoltagewithintheproduct’senclosure

thatmaybeofsufcientmagnitudetoconstituteariskofelectric

shock to persons.

Theexclamationpointwithinanequivalenttriangleisintended

to alert the user to the presence of important operating

and maintenance (servicing) instructions in the literature

accompanyingtheappliance.

1. Readandfollowallinstructionsandwarningsinthismanual.Keepforfuturereference.

2. Do not use this apparatus near water.

3. Cleanonlywithadrycloth.

4. Donotblockanyventilationopenings.Installaccordingtomanufacturer’sinstructions.

5. Donotinstallnearanyheatsourcessuchasradiators,heatregisters,stovesorotherapparatus(including

ampliers)thatproduceheat.

6. Donotoverridethesafetypurposeofthepolarizedorgrounding-typeplug.Apolarizedplughastwoblades-one

widerthantheother.Agroundingtypeplughastwobladesandathirdgroundingprong.Thewidebladeorthe

thirdprongisprovidedforyoursafety.Iftheprovidedplugdoesnottintoyouroutlet,consultanelectricianfor

replacementoftheobsoleteoutlet.

7. Protectthepowercordfrombeingwalkedonorpinchedparticularlyatplug,conveniencereceptacles,andthe

pointwhereitexitsfromtheapparatus.

8. Onlyuseattachments/accessoriesspeciedbythemanufacturer.

9. Referallservicingtoqualiedservicepersonnel.Servicingisrequiredwhentheapparatushasbeendamagedin

anyway,suchaswhenthepower-supplycordorplugisdamaged,liquidhasbeenspilledorobjectshavefallen

intotheapparatus,theapparatushasbeenexposedtorainormoisture,doesnotoperatenormally,orhasbeen

dropped.

10. DONOTEXPOSETHISEQUIPMENTTODRIPPINGORSPLASHINGANDENSURETHATNOOBJECTS

FILLEDWITHLIQUIDS,SUCHASVASES,AREPLACEDONTHEEQUIPMENT.

11. TOCOMPLETELYDISCONNECTTHISEQUIPMENTFROMTHEACMAINS,DISCONNECTTHEPOWER

SUPPLYCORDPLUGFROMTHEACRECEPTACLE.

12. THEMAINSPLUGOFTHEPOWERSUPPLYCORDSHALLREMAINREADILYOPERABLE.

Warning:

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRICAL SHOCK.

DO NOT REMOVE COVER. NO USER

SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

B-500-MTRX-230-8x8 Installation Manual

Pg. 3

www.snapav.com Support: 866.838.5052

1. Important Safety Instructions

2. Product Overview

3. Package Contents

4. Features

5. Recommended for Installation

6. Device Layout

 6.1.FrontPanel

 6.2.RearPanel

7. Installation Setup

 7.1. BasicInstallationDiagram

7.2. Basic Instructions

 7.3. InstallationTips

 7.4. SwitcherLocationandPlacement

  7.4.1. RackInstallation

7.5. HDMI Input Connections

7.6. Output Connections

7.6.1. Choosing the Correct Output

7.6.2. HDMI Outputs

7.6.3. HDBaseT Outputs

 7.7.MatrixControlConnections

  7.7.1. IRControl

  7.7.2. RS232Control

  7.7.3. Ethernet/IPControl

 7.8.IRPass-ThroughInstallationandSetup

  7.8.1. MatrixSwitcherIRConnections

  7.8.2. MatrixSwitcherIRPortConguration

 7.9. B-500-RX-230-IRIRConnections

  7.9.1. IRReceiver

  7.9.2. IRFlasher

  7.9.3. YellowTagIRAdapter

 7.10.IRApplicationDiagrams

  7.10.1.IRPass-ThroughfromControlSystem

  7.10.2. IRPass-ThroughfromRoomstoSources

8. EDIDConguration

8.1. Source Setup

 8.2.DisplaySetup

 8.3. AutoEDIDConguration

  8.3.1. HowtoCongureAutoEDID

 8.4.EmbeddedEDIDConguration

  8.4.1. EmbeddedEDIDChart

  8.4.2. HowtoSetEmbeddedEDIDforaSingleInput

  8.4.3. HowtoSetEmbeddedEDIDforAllInputs

 8.5.EDIDLearning

  8.5.1. HowtoLearnEDIDtoaSingleInput

  8.5.2. HowtoLearnEDIDtoaAllInputs

 8.6.ViewingInputEDIDStatus

9. AdvancedSetupUsingtheCongurationUtility

 9.1.IRSourceRouting

 9.2.IRFrontPanelIREnable

 9.3.MatrixControlfromRoomEnable

 9.4.FrontPanelPowerButtonActive

10. Firmware Update

11. Operation and Control

 11.1.IRRemote

  11.1.1.RouteInputstoOutputs

  11.1.2.TurnOff(Mute)Outputs

  11.1.3.DisplayOutputStatus

  11.1.4.ResettingtoFactoryDefaults

12. Troubleshooting

 12.1.GeneralTroubleshootingGuidelines

 12.2.NoSignalfromSourcetoanyDisplay

 12.3.NoSignalfromanySourcetoanDisplay

 12.4.Audioissues

13. Contacting Tech Support

14. System Layout Chart

15. Specications

16. Warranty

Table of Contents

B-500-MTRX-230-8x8 Installation Manual

Pg. 4

™

2. Product Overview

Welcome to Binary™, one of the most highly regarded brands available today. This product is engineered to

provide years of exceptional reliability. We appreciate your business and we stand committed to providing our

customerswiththehighestdegreeofqualityandserviceintheindustry.

TheB-500-MTRX-230-8x8isastate-of-the-artHDMImatrixswitcherwithbothHDMIandHDBaseTOutputs.Itprovides

truematrix routingforHDMIsignals.WithfeaturessuchasHDMI3Dsupport,sophisticatedEDIDhandling,andIR,

RS232 and Ethernet control, this product is ideal for residential and commercial media distribution systems. The

HDBaseTconnectiononeachoutputextendsHDMIsignalandbi-directionalIRtoremoteroomsupto230feetaway

viaCat5e/Cat6/Cat6a.

Note: This manual covers all aspects of installation and setup of the B-500-MTRX-230-8X8 for most application. Some

features must be congured using the Conguration Utility software. Go to the product page for the B-500-MTRX-

230-8X8 at www.SnapAV.com and click on the Support Tab to download the Conguration Utility and manual.

4. Features

• (8)HDMIinputsby(8)mirroredHDMIandHDBaseToutputs

• Upto16displayscanbeattachedintotal(usingbothHDMIandHDBaseToutputs)

• SupportsVideoresolutionsupto1080p/6036bitcolor

• SupportsallHDMIaudioformatsincludingDolbyTrueHDandDTSMasterHD

• SupportsallHDMI3Dformats

• SophisticatedEDIDhandlingincludingEmbedded,Learned,andAutomodes

• HDMIorDVIwithadapter(notincluded)

• IRControlfromintegratedreceiveror3.5mminput

• Bi-directionalIRpass-throughwhenusingB-500-RX-230-IR

• HomeAutomationControlviaIR,RS-232andEthernet

• PCSetupandCongurationusingdedicatedsoftware

• HDCP2.0compliant

• CECPassThrough

5. Recommended for Installation

• PhillipsScrewdriver(forrackearattachment)

• Upto8sources

• Upto8displays(16ifusingbothHDBaseTandHDMIoutputs,seeSection7.6,Page9)

• BinaryHighSpeedHDMICablestoconnectsourcestoB-500-MTRX-230-8x8HDMIinputs

• BinaryHDMIcablesorB-500-RX-230-IRunitsandCat5e/6cableinstalledbetweenmatrixswitcherlocationand

displays(Seesection7.6.3.1,page10forHDBaseTwiringrecommendations)

• RJ45connectorsandterminationtools(IfusingB-500-RX-230-IR)

• ControlSystemtocontroloperationofB-500-MTRX-230-8x8

• WindowsPCwithCongurationUtilityinstalledandRS232adapter

• CongurationUtilityManual

3. Package Contents

• (1)B-500-MTRX-230-8x8

• (2)Rackearsformounting(screwsincluded)

• (1)IRRemoteControl

• (1)Powersupply24V5ADC

• (1)InstallationManual

• (1)CD-ROM

B-500-MTRX-230-8x8 Installation Manual

Pg. 5

www.snapav.com Support: 866.838.5052

6. Device Layout

6.1. Front Panel

1. Power On/Off Switch

 TogglePowerfromOntoStand-by.CanbedisabledfromCongurationUtilitysoftware.

2. Source Status LEDs

 IndicatesthattheselectedsourceisonandtransmittinganHDMIsignal.

3. Output Display

 Displaysthelastoutputselected.

4. IR Receiver Window

 IRreceiverforMatrixtocapturecommandssentbyIRremote.

5. Input Display

 Displaysthelastinputselected.

1 2

B-500-MTRX-230-8x8 Installation Manual

Pg. 6

™

6.2. Rear Panel

1. Power LED

 Indicatesthecurrentpowerstatusofthematrixswitcher.Solidredindicatesthatpowerison.

2. Latch-Locking Power Jack

 +24V5ADCpowersupplyconnectionwithlockingscrewcollarforsecureconnection.

3. RS-232 control port (DB9)

 AttachconnectionfromcontrolsystemorWindowsPCforserialcontroloftheB-500-MTRX-230-8x8.

4. IR Input to Room 1 through 8

 3.5mmmono-miniconnectionforIRpass-through.ConnectthecontrolsystemIRFlasheroutputstosendcommands

todisplaysorotherdevicesintheroom(onlywhenusingtheB-500-RX-230-IRtoextendtodisplays).

5. System IR In

 3.5mmmonominiIRinputportformatrixcontrol.

6. System All IR Out

 3.5mm monomini port,repeats all IRcommands fromall connectedHDBaseToutputs (fromIR Receiverport of

B-500-RX-230-IR).

7. IR Output to Source 1 through 8

 3.5mmmonominiconnectionsusedtoconnectIRashersforcontrollingsources.Theseportsmaybeconguredto

routecommandsonlyfromtheIRoutputcorrespondingtotheHDBaseToutputnumber(IRzonerouting),ordirectly

tothesourceselectedforviewingonanHDBaseToutput(IRsourcerouting).(SeeCongurationUtilityManual)

8. RJ45 HDBaseT Outputs 1 through 8

 Connect568BterminatedCat5e/6HDBaseTcableroutedtoaB-500-RX-230-IRupto230feetawaytofeedHDMI

signaltodisplay.OutputsimultaneouslydisplaysthesamesourceastheHDMIoutputofthesamenumber.

9. Link LEDs 1 through 8

 ThegreenLinkLEDsindicatethestatusoftheHDBaseTconnection.Off=Nolink;On=Linkisactive.

10. HDMI Outputs 1 through 8

 ConnectHDMIcablestoroutetodisplays.OutputsimultaneouslydisplaysthesamesourceastheHDBaseToutput

ofthesamenumber.

11. Ethernet Port

 RJ45portforconnectinganEthernetCat5e/6cableforIPcontroloftheB-500-MTRX-230-8x8.

12. HDMI Inputs 1 through 8

 ConnectHDMIcablesfromsourcestothematrixswitcherfordistribution.

PWR

Engineered in the USA

Manufactured in Taiwan

IR IN

ALL IR OUT

51 3 4 6 8 107

11 12

2 9

B-500-MTRX-230-8x8 Installation Manual

Pg. 7

www.snapav.com Support: 866.838.5052

7. Installation and Setup

7.1. Basic Installation Diagram

7.2. Basic Instructions

1. Unpackthematrixandinstallitnearthesourceequipment.(7.4.SwitcherLocationandPlacement,page8)

Note: Do not power the matrix switcher until it is indicated to do so.

2. InstallandconnecteachsourcetoaninputonthematrixswitcherusingtheshortestHDMIcablepossible.

 (7.5.HDMIInputConnections,page9)

3. InstallthedisplaysandoutputwiringtothematrixlocationusingHDMIcablesforstandardHDMIoutputor

Cat5e/6ifB-500-RX-230-IRReceiverswillbeused.(7.6.OutputConnections,page9)

4. RecordtheinputsandoutputsusedintheSystemLayoutChartforfuturereference.

 (14.SystemLayoutChart,page26)

5. Ifusingacontrolsystem,connectittotheappropriateportonthematrixswitcherforthedrivertypebeingused:

IR,RS232,orIPcontrol.(7.7.MatrixControlConnections,page11)

6. Installandcongurethedriverformatrixswitchingcontrolintothecontrolsystemprocessor.

 (7.7.MatrixControlConnections,page11)

7. InstalltheIRequipmentandsetupIRpass-throughifusingit.

 (7.8.IRPass-ThroughInstallationandSetup,page12)

8. Attachthepowersuppliestothematrix,sources,anddisplays,thenpowerupthesystem.

9. Testallinputandoutputselectionsforsync,reliableswitching,correctaudioformatandvideoresolution.Usethe

factoryremoteortheMatrixCongurationUtilitytosetupEDIDsasneeded.(8.EDIDConguration,page16)

10. ChangeanyadvancedsettingsintheMatrixCongurationUtilityasneededtosuittheinstallation.

 (9.AdvancedSetupUsingtheCongurationUtility,page20)

Completethebasicinstallationsectiontosetupthematrixswitcherformediadistributionbeforecompletinganyother

setup.Usethisdiagramforreferenceduringbasicinstallationofthematrixswitcher,sources,displaysandwiring.

Thesearethebasicstepsthatmustbetakentoconnectequipmenttotheinputsandoutputsofthematrixswitcher

andcongurethesystemforuse.Seethesectionslistedforfullinformationoncompletingeachstep.

PWR

Engineered in the USA

Manufactured in Taiwan

IR IN

ALL IR OUT

Projector

Game

Console

HDTV HDTV HDTV

RS232

HDMI

HDMi

HDMI

B-500-RX-230-

Cat5e/6

HDMI

Home Automation System

Blu-ray Player Cable/Sat Box

AC Power

B-500-MTRX-230-8x8 Installation Manual

Pg. 8

™

7.3. Installation Tips

7.4. Switcher Location and Placement

Followingthesetipsduringtheinstallationprocesswillhelpguaranteeasuccessfulinstallation.

• Test every cable before use.

 Alwaystestcablesbeforeuse.Field-terminatedcablesshouldbecheckedforcontinuityafterterminationtobe

suretheconnectorswereinstalledcorrectly.

• Label each cable as it is installed.

 Thiswillaidinconnectionsetupandprogramming,andwillalsomakeiteasiertocomebacktoajobatalater

dateandimmediatelyknowwhatisconnectedwhere.

• Complete the System Layout Chart (page 26) in the back of the manual during installation.

 Recordthesourceconnectedtoeachinput,theoutputnumberofeachdisplay,andthemethodofroutingsignalin

thechartforreferenceduringinstallationandsetup.Useitafterwardtokeeptrackofequipmentinuse,openports

forexpansion,andtohelpidentifywheretotroubleshootissuesiftheyariselater.

• LeaveanRS232connectioneasilyaccessibleforusingtheCongurationUtility.

 TheB-500-MTRX-230-8x8isequippedwithmanysetupfunctionsthatmustbeaccessedbyusingaPCandthe

CongurationUtility.LeaveanRS232cableconnectedduringsetupandtestingthatcanbeconnectedtothePC

withease.IfthematrixisbeingcontrolledbyRS232,disconnectthecontrolsystemwhileusingtheUtility.

• Do not fully secure wiring and equipment until setup and testing has been successfully completed.

 Waituntilallprogramming,sources,andzoneshavebeensetupandthoroughlytestedtostrapwiringand

equipmentdown,inordertoavoidrestrictingaccesstoconnectionsandsettingsontheequipment.

• Complete initial setup with all sources connected to the matrix locally.

 IfasourcewillbeconnectedtoaninputbyanHDMIextender,completeinitialsetupbyconnectingdirectlytothe

inputwithashortHDMIcable.Relocatethesourceandinstalltheextenderafterthesourcehasbeensetupand

tested,andthenconrmthenewarrangementworks.

Binarymatrixswitchersaredesignedtodeliverunsurpassedtechnologywithsuperiorperformance.However,where

youinstalltheswitchercanhavealargeeffectontheperformancethatyoureceive,andthelifeoftheunit.Hereare

someguidelinestofollowwheninstallingaB-500-MTRX-230-8x8Switcher.

• Besurethattheunitisinawell-ventilatedareathatprovidesadequatecooling.

• Donotblockthecoolingventslocatedonbothsidesoftheunit.

• Donotplacetheunitoncarpetingoranysimilarmaterial.

• Donotinstalltheunitnearasourceofheat,orinanextremelyhumidorwetlocation.

• Ifyourinstallationlacksgoodairow(suchassolidcabinetdoorsorwall-mountedracks),itmaybenecessaryto

createventilationtoallowoutsideairintothespace.

• Allowaminimumof3”offreeairspaceoneithersideoftheunit.(Doesnotapplytorackmounting)

• Allowaminimumof2”ofdepthbehindunittoaccommodatecablesandconnectors.

• Whenplacingonacabinetshelf,positiontheunitwithallfeetrestingonasolidlevelsurface.

7.4.1. Rack Installation

TheB-500-MTRX-230-8x8canbemountedinarackwiththefrontorrearpanelfacingoutward,andwilldisplace2U

ofverticalspacewheninstalled.Rear-facinginstallationallowsforeasyaccesstotheconnectionsforinstallations

thatdonotrequirethefrontpaneloftheunittobeaccessed.Front-facingmountingisusefulforapplicationswhere

thefrontpanelmustbeaccessibleorvisible.

Therackearsarepackagedseparatelyfromthematrixswitcherinthebox.Attachtheearstothesidesofthematrix

atthefrontorbackusingtheincludedscrews.Tightenthemwitha#2PhillipsScrewdriver.Itmaybenecessaryto

removethefeetfromthebottomwhenrackmountingthematrixswitcher.Removethescrewsforthefeetwitha#2

PhillipsScrewdriver,andstorethefeetandscrewstogetherincasetheyareneededinthefuture.

Note: The rack ears and mounting holes are only designed to safely hold the weight of the B-500-MTRX-230-8x8.

Do not use the matrix switcher as a shelf for other equipment in the rack.

B-500-MTRX-230-8x8 Installation Manual

Pg. 9

www.snapav.com Support: 866.838.5052

7.5. HDMI Input Connections

7.6. Output Connections

EachoftheeightinputsontheB-500-MTRX-230-8X8utilizesastandardHDMIportforconnection.Followthese

guidelineswhenconnectingsourcestotheinputs.

• Alwaysusetheshortestcablepossiblebetweensourceequipmentandthematrixswitcherinputs.Usehigh

speed ratedcablestoguaranteethebestpossibleperformance.

• AvoidusingHDMIcableadaptersinruns.Alwaysrunoneunbrokencablewhenpossible.

TheB-500-MTRX-230-8X8isequippedwithoneHDMIandoneHDBaseToutputportforeachofthe8outputzones.

Seethesectionsbelowforspecicinstructionsanddetailsforeachconnectiontype.

Note: Any input selected on an output zone is played on both the HDMI and HDBaseT outputs for that zone

simultaneously. This can be used to feed the same source to two devices. Read more about this feature below.

7.6.1. Choosing the Correct Output

OutputstodisplayscanbeconnectedusinganHDMIcableoraCat5e/6cableandHDBaseTReceiver(withashort

HDMIcableconnectingtheReceivertothedisplay).Foranyrunoverabout50feet,orforanyoutputthatwillutilize

IRpass-through,useHDBaseT.

ForshortrunswhereHDMIcablescanberoutedtothedisplayand/ornoIRpass-throughisneeded,orifthereis

HDMIequipmentconnectedbetweenthematrixoutputandthedisplay(likeanAVreceiver),itmaybebesttousethe

HDMIoutputtoconnectequipment.

Insomesituationsitmaybebenecialtousebothoutputs.Iftwodisplaysneedtobefedthesamesourceatall

times,onedisplaycanbefedfromtheHDBaseToutput,andonefromtheHDMIoutput.InjobswithanAVreceiver

feedingsurroundsoundtoazone,theaudiocanbefedtothereceiverviaHDMI,andanHDBaseTreceivercanbe

usedtoroutevideotothedisplay.ThisisbenecialwithAVreceiversthathaveolderorlessreliableHDMIscalingor

pass-through.

7.6.2. HDMI Outputs

TouseanHDMIoutputtofeedadisplay,connectbetweentheoutputofthematrixswitcherandtheinputofthe

display.FollowtheguidelinesbelowwhenusingHDMIoutputsforthebestperformanceandreliability.

• Alwaysusetheshortestcablepossiblebetweenequipment.Usehighspeedratedcablestoguaranteethebest

possibleperformance.

• AvoidusingHDMIcableadaptersinruns.AlwaysrunoneunbrokenHDMIcable.

• WhenroutingHDMItoanAVreceiverforsurroundsound,thenoutofthereceivertoadisplay,makesuretoset

theAVreceivertoanHDMImodewherethesignalwillnotbeprocessedorscaledtoadifferentformat.Thiswill

avoidsignaltimingissuesthatcancauseintermittentsyncortotallossofsync.Contactthedevicemanufacturer

fordetailsregardingHDMIsetup.

B-500-MTRX-230-8x8 Installation Manual

Pg. 10

™

7.6.3. HDBaseT Outputs

FollowtheseguidelineswhenselectingandinstallingtheHDBaseTcable,andthenfollowtheinstructionsafterwardto

completetheconnectionsforanoutput.

7.6.3.1. HDBaseT Wiring Recommendations

Cable Type- Shielded or Unshielded Cat5e/6

• CableDistanceLimitations:

Cat5e/ Cat6: Upto200ft

Cat6a: Upto230ft

• UseatleastCategory5ehigh-qualitytwistedpairsolidconductorcableratedtonolessthan350Mhzbandwidth.

Thehigherthecablestandard,thebetteritwillperform.

• Forthebestresultsinstallashieldedcable.Thiswillpreventsignaldropoutandartifactsfrombeingcausedby

electromagneticandradiointerference(EMI/RFI)fromceilingfans,appliancesandelectricmotors.

• Usenomorethantwo5meterorshorter,solidorstranded,568Bterminatedpatchcablesintherun.Useshielded

patchcablesiftherunisshieldedtomaintainshieldcontinuity.

• Usenomorethantwokeystonesorcouplersintherun.Useshieldedkeystonesorcouplerswithshieldedcable

tomaintaincontinuity.

• Cleanlyterminateallcableendsandtesteverycableusedbeforeconnectingtheextendertoavoid

troubleshootingterminationproblemslater.

• MarkeachendoftheHDBaseTcablewiththeincludedlabelstoavoidconfusionlater.

Connector Type- RJ45

• UseahighqualityRJ45connectorthatmatchesorexceedsthestandardofthecableinuse.Shieldedconnectors

mustbeusedwithshieldedcables,andmustmaintaincontinuityoftheshieldtobothconnectorstoprotectfrom

interference.

• Wehighlydiscouragetheuseof“EZ”style,openendRJ45’swithHDMIextenders.

• AlwaysterminateRJ45connectorsintheHDBaseTsignalpathtothe568Bterminationstandardasrequiredby

HDBaseT standards.

7.6.3.2. Installation Instructions

1. InstalltheCat5e/6cableandterminatetheends.Thentestthecabletoensureoperation.

2. ConnecttheHDBaseTcabletothedesiredHDBaseToutputofthematrixswitcher.

3. ConnecttheHDBaseTcabletotheB-500-RX-230-IRReceiverortheHDBaseTdeviceinuse.

4. ConnectanHDMIcable(2metersorshorterisrecommended)betweentheHDMIOUTportontheReceiverand

thedesiredHDMIinputontheDisplay.

5. AttachthepowersupplytotheReceiverandpowertheunit.

6. Installationiscomplete.Testallconnectedinputsandoutputstogethertoensurereliableoperation.

7. ForIRPass-ThroughIntegration,seesection7.8.IRPass-ThroughInstallationandSetup,page12.

Pin 1 White/Orange Pin 5 White/Blue

Pin 2 Orange Pin 6 Green

Pin 3 White/Green Pin 7 White/Brown

Pin 4 Blue Pin 8 Brown

TIA/EIA Standard 568-B (Gold Pins Facing Up)

B-500-MTRX-230-8x8 Installation Manual

Pg. 11

www.snapav.com Support: 866.838.5052

LINK LINK

PWR

LINK LINK LINK LINK LINK LINK

Engineered in the USA

Manufactured in Taiwan

IR IN

ALL IR OUT

Matrix IR

Control Input

7.7. Matrix Control Connections

Alldrivers,associatedsoftwareandextradocumentationisavailableontheB-500-MTRX-230-8X8productpageat

www.SnapAV.comundertheSupportTab.

7.7.1. IR Control

TheB-500-MTRX-230-8X8canbecontrolledbyIRfromthefrontpanelreceiverorby

attachingamonocablefromthecontrolsystemasheroutputtothe“SystemIRIn”port

onthebackofthematrixswitcher.Forthemostreliablecontrol,usetheSystemIRInport.

ThematrixswitcherwillalsoprocesscommandsreceivedonIRReceiverinputsfrom

B-500-RX-230-IRinzonesconnectedviaHDBaseT.(SeeSection7.10.2.IRPass-ThroughfromRoomstoSources

onpage15foranapplicationexampleofthisfeature.)

Note: System IR Control and the front panel IR Receiver can be disabled when not in use by using the Conguration

Utility. See the Conguration Utility manual section, “Other Settings” for more information.

7.7.2. RS232 Control

TocontroltheB-500-MTRX-230-8x8withRS232,thedevicesmustconnectusingthecorrectpincongurationforthe

controlsysteminuse.

Thematrixswitcherreceivescontroldataonpin2(RxD–DataReceive)andtransmitscontroldataonpin3(TxD

-DataTransmit).TheconnectioncablebetweenthematrixswitcherandtheAutomationSystemwillneedtobe

conguredsothatpin2(RxD)ontheswitcherisconnectedtothecontrolsystemTxDpin,andpin3(TxD)onthe

switcherisconnectedtothecontrolsystemRxD(DataReceive)pin.Seethediagrambelowfordetails.

Congurationforcontrolsystemserialportscanvary.Refertothedocumentationforthesysteminusetoensure

properconnectionandconguration.

Note: This port is also used to communicate with a PC when using the PC Conguration Utility. Refer to the

Conguration Utility manual for details.

7.7.3. Ethernet/IP Control

TheB-500-MTRX-230-8x8includesanEthernetportthatcanbeusedtocontrolthedeviceusingTelnetProtocol.This

portfollowsTIA568A/Bstandards;pleaserefertothesestandardswhenterminatingcables.

Tocongurethematrixswitcherforusewiththedriver,itwillbenecessarytoconnecttheunittoaPCandaccessit

withtheMatrixCongurationUtility.SeetheCongurationUtilitymanualandtheIPdriverdocumentationforcomplete

setup instructions.

B-500-MTRX-230-8x8RS232PortConguration

LINK LINK

PWR

LINK LINK LINK LINK LINK LINK

Engineered in the USA

Manufactured in Taiwan

IR IN

ALL IR OUT

DB9 Female Connector

RxD (Data Receive)

TxD (Data Transmit)

GND

Pin Function

2 RxD(DataReceive)

3 TxD(DataTransmit)

5 Ground/Common

B-500-MTRX-230-8x8 Installation Manual

Pg. 12

™

7.8. IR Pass-Through Installation and Setup

ToutilizeIRpass-throughbetweenadisplaylocationandthematrixswitcher,installaB-500-RX-230-IRatthedisplay

anduseHDBaseTforroutingthesignal.Thematrixswitcherandthematrixreceiverareequippedwithportstoallow

commandstobesenttothedisplayorfromthedisplayarea.ThissectiondetailsthepinoutsandcorrectuseoftheIR

pass-through ports.

7.8.1. Matrix Switcher IR Connections

Theportsindicatedinthediagramaredescribedindetailbelow.Guidesforstandardapplicationsareincludedonthe

followingpagesforreferenceduringsetup.

7.8.2.MatrixSwitcherIRPortConguration

AllIRconnectionportsontheB-500-MTRX-230-8X8are3.5mmmonominiandusethispinoutconguration.Consult

withthemanufacturerofanyattachedIRequipmenttoconrmtheirpinoutmatchesbeforeuse.

1. IR Input to Room 1 through 8

Use3.5mmmini-monocablestoconnectIRasheroutputsonacontrolsystemtotheseportstosendcommands

todisplaysorequipmentlocatedattheB-500-RX-230-IRmatrixreceiverlocation.Thenumbercorrespondstothe

outputzonenumber,soIRInputtoRoomport1willsendsignalstoHDBaseToutput1.

2. System IR In

 3.5mmmonominiIRinputportformatrixswitcherIRcontrol.

3. System All IR Out

 ThisportrepeatsanycommandsentfromtheIRReceiverportsonB-500-RX-230-IRMatrixReceiversconnected

to any HDBaseT output.

4. IR Output to Source 1 through 8

 TheIRoutputfromeachconnectedB-500-RX-230-IRistransmittedtotheIROUTPUTTOSOURCEports.

Commandscanberoutedtothesourceselectedortothelike-numberedport.

LINK LINK

PWR

LINK LINK LINK LINK LINK LINK

Engineered in the USA

Manufactured in Taiwan

IR IN

ALL IR OUT

1 2 3 4

IR Signal (Tip)

GND (Sleeve)

IR Signal Tip

GND (Ground) Ring

B-500-MTRX-230-8x8 Installation Manual

Pg. 13

www.snapav.com Support: 866.838.5052

7.9. B-500-RX-230-IR IR Connections

TheB-500-RX-230-IRIRportsaredescribedbelow.Usethediagramforreference.

7.9.1. IR Receiver

AttachanIRreceivertothisporttocaptureIRcommandsintheroomforpass-throughforsources.Thisportwillalso

sendcommandsbacktothematrixswitcherforcontrolofsourceselectionineachzone.

7.9.2. IR Flasher

AttachanIRashertothisportforcontrollingadisplayorotherequipmentwithcommandssentfromacontrolsystem

asheroutput,intothematrixswitcherIRINPUTTOROOMportsandthentothisport.

1 2

IR Signal (Tip)

GND (Ring)

12V DC (Sleeve)

IR Signal Tip

GND (Ground) Ring

+12V DC Sleeve

IR Signal (Tip)

GND (Sleeve)

IR Signal Tip

GND (Ground) Ring

7.9.3. Yellow Tag IR Adapter

Theyellowtaggedadapter(illustratedbelow)includedwiththeB-500-RX-230-IRisusedwhenplugginga3.5mm

monominicableintotheIRReceiverportoftheB-500-RX-230-IR.ThisisusedtosendIRcommandstothematrix

switcherlocationfromotherdevicesinsteadofanIRReceiverthatusea3.5mmmonominiportforoutput.

IR Signal (Tip)

GND (Ring)

12V DC (Sleeve)

IR Signal (Tip)

GND (Sleeve)

To IR Control System

Connecting Block

To B-500-MTRX

B-500-MTRX-230-8x8 Installation Manual

Pg. 14

™

7.10. IR Application Diagrams

7.10.1. IR Pass-Through from Control System

ThediagramaboveillustratesatypicalinstallationwithaB-500-MTRX-230-8X8wherealloftheequipmentisbeing

controlledbyacontrolsystemthatusesRF(RadioFrequency)remotesineachoutputzone.

• TheRFremotestransmitcommandsbacktothecontrolsystemwhichthensendscommandstoeachdevice

beingcontrolled.Customprogrammingbytheinstallersetsthecontrolsystemuptoautomaticallyswitchinputs

andoutputsinthematrixswitcherasneeded,sotheenduseronlyhastoselectthesourcetheywanttowatch.

• Eachdisplay(onlyoneispicturedforreference)requiringIRcontrolisconnectedtothesystemviatheHDBaseT

outputofthematrixswitcher.Cat5e/6cableconnectstoaB-500-RX-230-IRReceiver,whichisattachedtothe

displayviaHDMIforsignal.AnIRasherconnectedtotheIRasherportsendstheIRcommandstothedisplay.

Sourcesaredirectlycontrolledbythecontrolsystem.

• IRcontrolfordisplaysisroutedfromthecontrolsystemtothematrixswitcherusing3.5mmmonominicables

pluggedintoIRINPUTTOROOMports.ThecommandspassfromamatrixswitcherporttotheHDBaseToutput

ofthesamenumber.Inthediagramthemonocableusedtosendcommandstotheoutput8zoneispluggedinto

IRINPUTTOROOMport8.Thisallowsdiscretecontrolofeachdisplayconnected,eveniftheyaremodelswith

thesamecodes.

• SomedisplaysandprojectorscanbecontrolledbyothermethodsthanIR.TheprojectorpicturedfeaturesIP

control,soitisreceivingcommandsfromthecontrolsystemoveranEthernetconnection.AnHDMIcableis

connectingittothematrixswitcheroutputsinceitisinstalledcloseenoughtotheequipmentandrequiresnoIR

asher.

• Whenthesystemisinuse,iftwooutputsareconnectedtothesameinput,thesourcewillchangeonbothoutputs

withanycommandsentsinceitcan’tsendtwoHDMIstreamsatonce.Thismustbeconsideredwhendecidingon

thesourcestoconnectfordistribution.

Example:Inahomewithvedisplaysconnected,ifusersineveryroomwanttowatchsatelliteon

differentchannels,theremustbevesatellitereceiverssetupassources.Withcustomprogramming,

eachoutputcanbeprogrammedtouseonlyoneofthesatellitesourceinputs,givingeachoutputa

dedicatedcablebox,whileallowingotherless-usedsourcestoconnecttoanyoutput.

PWR

Engineered in the USA

Manufactured in Taiwan

IR IN

ALL IR OUT

B-500-RX-230-IR

IR Outputs

RS232

IR Inputs

Projector

RS232 Cable

HDMI

Cat5e/6

HDMI

PLAY

HDMI Source

256

HDMI

Source

IR Flasher

3.5mm Mono

HDMI

HDTV

IR Flasher

Cat5e/6

Ethernet Connection

Cat5e/6Ethernet Connection

B-500-MTRX-230-8x8 Installation Manual

Pg. 15

www.snapav.com Support: 866.838.5052

7.10.2. IR Pass-Through from Rooms to Sources

PWR

Engineered in the USA

Manufactured in Taiwan

IR IN

ALL IR OUT

B-500-RX-230-IR

Projector

HDMI

Cat5e/6

HDMI

PLAY

HDMI Source

256

HDMI Source

IR Flasher

HDMI

HDTV

IR Receiver

B-500-RX-230-IR

Cat5e/6

IR Receiver

HDMI

ThediagramaboveillustratesatypicalinstallationwithaB-500-MTRX-230-8X8wherealloftheequipmentisbeing

controlledbyIRremotesineachoutputzone.

• Ineachroomwithaconnecteddisplay,anentry-leveluniversalIRremoteisbeingusedtocontrolthedisplay

andsourcesinuse.CustomprogrammingsetupineachremotebytheinstallersendsIRcommandsoutofthe

remotemeantforthedisplaydeviceintheroom,thesources,andthematrixswitchersimultaneously.Thematrix

commandsareprogrammedtobesentautomaticallyasneededsotheenduseronlyhastoselectthesourcethey

want to watch.

• Tomakethissystemworkseamlessly,twoadvancedIRoptionshavebeenenabledinthematrixswitcher

CongurationUtility“OtherSettings”menu:IRSourceRoutingandIRMatrixControlfromroom.

 o IRSourceRoutingallowsthecommandsfromtheroomtoberouteddirectlytothesourceselectedtobe

displayedintheroom.ThissimpliesIRroutingbecauseonlyoneasherhastoconnecttothesource.

 o IRMatrixControlsetsthematrixswitchersothatanycommandsentfromanyHDBaseToutputtocontrolthe

matrixisautomaticallyreceivedinternally,eliminatingtheneedforanexternalconnectionbacktothematrix

forcontrol.SeeSection9.AdvancedSetupUsingtheCongurationUtilityonpage20formoreinformationon

changing these settings.

• Whenthecommandsaresent,thedisplaydeviceiscontrolleddirectlybytheremote.Thecommandsforthe

matrixswitcherandsourcesarepickedupbytheIRreceiverconnectedtotheB-500-RX-230-IRandsentbackto

thecorrectIROUTPUTTOSOURCEportandtothematrix.

• Whenthesystemisinuse,iftwooutputsareconnectedtothesameinput,thesourcewillchangeonbothoutputs

withanycommandsentsinceitcan’tsendtwoHDMIstreamsatonce.Thismustbeconsideredwhendecidingon

thesourcestoconnectfordistribution.

Example:Inahomewithvedisplaysconnected,ifusersineveryroomwanttowatchsatelliteon

differentchannels,theremustbevesatellitereceiverssetupassources.Withcustomprogramming,

eachoutputcanbeprogrammedtouseonlyoneofthesatellitesourceinputs,givingeachoutputa

dedicated cable box while allowing other less-used sources to connect to any output.

B-500-MTRX-230-8x8 Installation Manual

Pg. 16

™

8. EDIDConguration

8.1. Source Setup

8.2. Display Setup

8.3.AutoEDIDConguration

Thedisplaysusedwithinaninstallationusuallyvaryfromroomtoroom,andsomemaynotsupportallresolutions

availablefromasource.Itisnecessarytomakesuresourceswillprovideavideoandaudioformatcompatiblewith

allconnecteddisplaysprogrammedtousethem.Toaccomplishthis,theB-500-MTRX-230-8X8includesbuilt-in

EDIDmanagementforeachsourceinput.ThestoredEDIDispersource,soalldisplaylocationswillseethesame

resolutionandhavethesameaudioformatwhenthatsourceisselected.

Note: Source is only able to output one video resolution and one audio format.

Note: The default EDID for each input is always 1080p with 2 channel stereo audio, since this format is accepted by

most displays with no issues.

ThefollowingsectionsexplainconguringEDIDsviatheincludedIRRemote.BeforeconguringtheEDID,besureto

refertothesourceanddisplaymanualsforavailablefeaturesandresolutionsforeachdevice.Formoreinformation

aboutusingtheincludedremote,seeSection11.1IRRemoteonpage21.

WhileallEDIDcongurationsareavailableviatheremote,theCongurationUtilitycanbeusedforfastersetup.

DownloadtheCongurationUtilityandmanualontheSupportTabattheproductpagefortheB-500-MTRX-230-8X8

atwww.SnapAV.com.

What is EDID? EDID, or Extended Display Identication Data, is a stream of information sent from a display to a

source when the two devices are connected to tell the source what video and audio formats the display can use. This

prevents sources from outputting media that won’t work with the display.

Checkeachsourceandconrmthattheaudioformatandvideoresolutionaresetsothattheywillchangebasedon

theEDID.Normallythissettingiscalled“Auto”orsimilar.

Note: EDID setup is not required if the source supports setting one xed video resolution and audio format.

ItisrecommendedthatConsumerElectronicsControl(CEC)beturnedOFFinalldisplayswhenusingtheB-500-

MTRX-230-8X8.Thiswillprovideforpropercommunicationofvideo/audiosignalsandallowEDIDstofunctionat

theiroptimumperformance.Refertothedisplay’smanualforinformationonhowtoturnthisfunctionOFF.

ThequickestandeasiestmethodforcongurationistouseAutoEDID.Whenthismodeisusedthematrixswitcher

looksattheEDIDfromeachoftheconnecteddisplays.Itusesthehighestcommonvideoresolutiontocreateanew

EDIDandsavesthatEDIDinalloftheinputs.

Note: Auto EDID sets audio to 2ch stereo for all inputs regardless of the capability of the connected displays. If

multi-channel audio is desired, embedded EDIDs or Learned EDIDs will need to be used.

When to use Auto EDID

• Allsourceswillbeavailableonalldisplays.

• Asarststeptocongurationfollowingupwithadvancedmethodsforparticulardisplaysanddedicatedsources.

• ForadvancedEDIDcongurationwhenusingalegacydisplayand/ordedicatedsources,useembeddedEDIDsor

learningasdescribedinthefollowingsections.

Sets EDID Based on All Connected Displays Display Readout (Example)

1.PressDEFAULT

E-

2.PressNumberKey9

3.PressENTER

8.3.1.HowtoCongureAutoEDID

TosetupAutoEDIDconguration,rstmakesurethatalldisplaysarepoweredonandconnectedtothematrix

switcher.Then,pressthefollowingremotebuttonsinthisorder.Besuretopresseachbuttonwithin10secondsofthe

previousbutton-presstopreventthecommandfromresetting.

B-500-MTRX-230-8x8 Installation Manual

Pg. 17

www.snapav.com Support: 866.838.5052

8.4.EmbeddedEDIDCOnguration

Inadditiontotheautomaticcongurationmethod,EDIDsintheB-500-MTRX-230-8X8canbesettoinputsmanually

byselectinganEDIDfromtheembeddedlist(defaultEDIDsprogrammedintothematrixswitcher).

Thematrixswitchercontainseight‘embedded’EDIDsthatmaybeassignedtoinputs.TheseEDIDsdenegroupsof

videoandaudiocapabilitiesthatareusefulforconguringsourcesinmostsystems.

8.4.1. Embedded EDID Chart

Explanation of Embedded EDIDs

Video ResolutionintheEmbeddedEDIDsisthehighestresolutionaconnectedsourcewilloutput.Thatis,ifthe

sourceiscapableof1080P@60itwillberequiredbyEDIDs1-6toprovidethatresolution.However,ifthesource

isonlycapableof1080iitwilloutput1080i,etc.Itisassumedthatanydisplaythatcanacceptthespeciedvideo

resolutioncanalsoacceptallstandardvideoresolutionslessthanthatspecied.

Color Depthisthemaximumnumberofbitsusedtoencodecolor.24bitcolordepthis8bitspercolor(red,blue,

green).

3Dindicatesthatthesourcecanoutput3Difitisavailableinthecontent.

Audio Format indicatesthemaximumnumberofaudiochannels,aswellastheaudioformatthatthesourceis

allowedtooutput.ForanEmbeddedEDIDwith7.1chAudioFormat,thesourcedevicewilloutputthehighestaudio

possiblebasedonthecontent.Forexample,if7.1chisnotavailableand5.1chisavailable,thentheoutputwillbe

5.1ch.Thesameistrueif2chstereoistheonlyaudioavailablefromthesource.EmbeddedEDIDswith2chstereowill

limitoutputtothataudioformatregardlessofwhatisavailableinthecontent.

Embedded EDIDs 7 and 8areprovidedforlegacydisplaysthatcanonlyacceptresolutionsuptoamaximumof

1080i/720p.The1080iislistedrstsincealmostallolderHDdisplayscanaccept1080ibutnotallcanaccept720p.

ForthesetwoEmbeddedEDIDs,(7&8)thesourcewilloutput1080i.Should1080inotbeavailable,thesourcewill

output 720p.

Note: There is a possibility that 720p may not work for a very small number of older displays that may still be in use. It

will be necessary to use a Learned EDID from the display to store in the Input EDID of any sources that will be

routed to that display if 720p is not supported. See Section 8.5. EDID Learning on page 18 for directions to set

a learned EDID.

When to Use Embedded EDIDs

• 2channelaudioisrequiredforaparticularoutput.

• Lowervideoresolutionisrequiredforaparticularoutput.

Embedded EDID Resolution Color Depth Audio

1 1080p@60Hz 24-Bit 7.1ch

2(FactoryDefault) 1080p@60Hz 24-Bit 2ch

3 1080p@60Hz 24-Bit 3D 7.1ch

4 1080p@60Hz 24-Bit 3D 2ch

5 1080i@60Hz 36-Bit 3D 7.1ch

6 1080i@60Hz 36-Bit 3D 2ch

7 1080i@30Hz/720p@60Hz 24-Bit 7.1ch

8 1080i@30Hz/720p@60Hz 24-Bit 2ch

B-500-MTRX-230-8x8 Installation Manual

Pg. 18

™

8.4.2. How to Set Embedded EDID for a Single Input

8.5.1. How to Learn EDID to a Single Input

8.4.3. How to Set Embedded EDID for All Inputs

Example: Input =1 Embedded EDID=4 Display Readout (Example)

1. PressDEFAULT

E-

2. PressNumberKey(1-8)toselectoneEmbeddedEDID

3.PressINPUT

4. PressNumberKey(1-8)toselecttheInputtowhichtheEDID

isapplied

5. PressENTER

(success)

(fail)

Example: Input =1 Embedded EDID=4 Display Readout (Example)

1. PressDEFAULT

E-

2. PressALLtoselectallInputs

A-

3.PressNumberKey(1-8)toselectEmbeddedEDID

4. PressENTER

(success)

(fail)

8.5. EDID Learning

FormoreadvancedEDIDconguration,learningcanbeusedtoassignEDIDsdirectlyfromdisplaystooneormore

inputs.Thisisusefulwhenthesystemcontainsadisplaythatcannotacceptthehighestresolutionavailablefrom

sources,butallsourcesneedtobeavailabletoalldisplays.

Note: EDIDs can be learned from displays connected via the HDBaseT or the HDMI output.

When to Use Learned EDIDs

• AnolderdisplaydoesnotworkproperlywithanyoftheembeddedEDIDs.

• WhenthesourceisaPCitmaybenecessarytousealearnedEDID.

• LearningEDIDtoasingleinput

Example: Input =1 EDID Learned from Output 4 Display Readout (Example)

1. PressLEARNonceforHDMIportortwiceforHDBaseT

port

L.-.

2.PressOUTPUT

3.PressNumberkey(1-8)toselecttheOutputtheEDID

islearnedfrom

4.PressINPUT

L-

5.PressNumberKey(1-8)toselecttheInputtowhichthe

EDIDisapplied

6.PressENTER

(success)

(fail)

B-500-MTRX-230-8x8 Installation Manual

Pg. 19

www.snapav.com Support: 866.838.5052

8.5.2. How to Learn EDID to All Input

Example: Input=All EDID Learned from Output 4 Display Readout (Example)

1.PressLEARN

L.-.

2.PressOUTPUT

L-

3.PressNumberKey(1-8)toselecttheOutputtheEDID

islearnedfrom

4.PressENTER

(success)

(fail)

8.6. Viewing Input EDID Status

IfthereisaquestionabouttheEDIDsetforaninput,thestatusofthatinput’sEDIDcanbereviewedusingthe

includedIRremoteandwatchingthematrixswitcherfrontpaneldisplay.

Notes about EDID Status

• IftheEDIDwaslearnedfromanoutput,theexactEDIDspecicationswillnotbeshown,buttheoutputnumber

willbeidentied.Reviewthespecicationsofthedisplayattachedtotheoutputtodetermineitscompatible

resolutions.

• Iftheseconddigit(theInputbeingqueried)hasadotafterit,thentherstdigitistheEDIDnumberfromthe

EmbeddedEDIDtable.

• Iftheseconddigit(theInputbeingqueried)doesnothaveadotafterit,therstdigitistheOutputtheEDIDwas

learnedfrom(step4fromexampleabove).

Example: View the EDID for Input 3.

DisplayReadout(Example)

EDID5Assigned

fromEmbedded

EDIDTable

EDIDLearned

fromOutput4

1.PressSTATUS

-- --

2.PressINPUT

-- --

3. PressNumberKey(1-8)toselectthedesiredInput

-3 -3

4.PressENTER

5.3. 4.3

B-500-MTRX-230-8x8 Installation Manual

Pg. 20

™

9. AdvancedSetupUsingtheCongurationUtility

10. Firmware Update

There are several setup options available that can only be modied using the matrix switcher Conguration Utility.

Theseitemsaredefaultedtothemostcommonsettingsthatshouldworkinmostinstallations.

TheCongurationUtilityandmanualareavailablefordownloadontheSupportTaboftheB-500-MTRX-230-8X8product

pageatwww.SnapAV.com.DownloadandruntheUtilitytogainaccesstothesesettingsconnectingtothematrixand

clicking“OtherSettings.”

BinarymayoccasionallyreleasenewrmwarefortheB-500-MTRX-230-8X8toaddressnewstandardsandtechnology.

Itwillneverbenecessarytoperformanupdatetoanexisting,correctlyfunctioningsystem,butduringinstallationor

service,itisrecommendedtochecktheinstalledversiontobesureitisthenewestavailable.

Forfullupdateinstructions,seethesectiontitled,“FirmwareUpdate”intheCongurationUtilitymanual.Newrmware,

theCongurationUtility,andtheCongurationutilitymanualareavailablefordownloadontheSupportTaboftheB-500-

MTRX-230-8X8productpageatwww.SnapAV.com.

9.1. IR Source Routing

9.2. IR Front Panel IR Enable

9.4. Front Panel Power Button Active

9.3. Matrix Control from Room Enable

TheIRSourceRoutingfeatureallowsdiscretecontrolofthesourceselectedfromanyconnectedHDBaseToutputusing

anIRreceiverpluggedintotheB-500-RX-230-IR.Thissettingisonlyrelevantwhenusingin-roomIRremotestocontrol

sourcesconnectedtothematrixswitcher.WhensettoYes,thematrixwillroutecommandsfromtheHDBaseTReceiver

totheIROutputtoSourceportthatmatchesthesourceinputnumbercurrentlyselectedonthatoutput.

WhensettoNo,commandswillbesentonlyoutoftheIROutputtoSourceportthatmatchestheHDBaseTReceiver

numberfromwhichitoriginated.

ThissettingcontrolstheoperationofthefrontpanelIRreceiverbuiltintotheB-500-MTRX-230-8X8.Thisshouldbe

disabledifusingtheSYSTEMIRINporttocontrolthematrixswitcherviaIR,orifthematrixswitcherismissingor

receivingextracommandsduringuse(strayIRinterferingwiththeport).

TheFrontPanelPowerButtoncanbedisabledifdesired.Disablethebuttonwhenthematrixswitcherisprogrammed

tobeonatalltimesorinjobswhereturningoffthematrixfromtheswitchercancauseissueswithcontrol.

TheMatrixControlfromRoomEnableoptionallowsMatrixControlIRcommandstobesentfromtheroomasifasource

werebeingcontrolled.Turnthisoptionoffifthematrixswitcherisbeingcontrolledbyanyothermethodthanin-roomIR.

Note: To use Matrix Control from Room, it is recommended to program a universal remote control with discrete commands

for matrix control to keep in each zone, rather than using the included IR remote or commands learned from it.

Go to the Support Tab of the B-500-MTRX-230-8X8 product page at www.SnapAV.com to see and download the

available IR codes and drivers for IR remote programming.

Default Setting: Yes

Page is loading ...

Binary B-500-MTRX-230-16x16 Installation guide

Brand: Binary

Model: B-500-MTRX-230-16x16

Category: Supplementary music equipment

Type: Installation guide

This manual is also suitable for

Download PDF

report

Binary B-500-MTRX-230-16x16 Installation guide

This manual is also suitable for

Binary B-500-MTRX-230-16x16 Installation guide

Related papers

Other documents