AuthenTeak Kingsley-Bate SG30 St. George Assembly Instructions

Kingsley-Bate SG30 St. George

Brand: AuthenTeak

Model: Kingsley-Bate SG30 St. George

Type: Assembly Instructions

AuthenTeak Kingsley-Bate SG30 St. George is a high-quality garden furniture piece that combines durability with elegant design. Constructed from premium teak wood, this 4-foot swing offers a comfortable and inviting seating experience for outdoor relaxation. The swing features a sturdy frame with mortise and tenon joinery, ensuring stability and longevity. Assembly is straightforward, with step-by-step instructions and pre-drilled holes for easy dowel and screw insertion. Enjoy the beauty of natural teak as you unwind in the comfort of your own backyard oasis.

AuthenTeak Kingsley-Bate SG30 St. George is a high-quality garden furniture piece that combines durability with elegant design. Constructed from premium teak wood, this 4-foot swing offers a comfortable and inviting seating experience for outdoor relaxation. The swing features a sturdy frame with mortise and tenon joinery, ensuring stability and longevity. Assembly is straightforward, with step-by-step instructions and pre-drilled holes for easy dowel and screw insertion. Enjoy the beauty of natural teak as you unwind in the comfort of your own backyard oasis.

Kingsley-Bate

SG30 St. George 4' Swing

Assembly Instructions

KINGSLEY – BATE

Fine Garden Furniture

ASSEMBLY INSTRUCTIONS FOR THE SG - 30

RIGHT END FRAME BACK LEFT END FRAME

SEAT

STEP-I

Unpack, inspect and lay the parts on a clean, flat, soft surface to avoid marring the wood.

NOTE: During assembly of the furniture pleas e match all joints with the corresponding

letters or numbers stamped on the furniture.

*NOTE

A TENON

B MORTISE HOLE

STEP-II

Fit the BACK tenons into the LEFT END FRAME

mortise holes. If necessary, gently rock the BACK

while pushing the tenons into the mortise holes until all

joints fit snugly together.

STEP-III

Place the SEAT against the LEFT END FRAME as shown in the

assembly diagram and insert the back SEAT tenon into the mortise hole

at the center of the bottom rail of th e BACK. Again, please be sure to

match up the stam ped letters or numbers on the SEAT and the END

FRAME. There is a front and a back to the SEAT.

STEP-IV

Slide the FRONT SEAT RAIL tenon into the LEFT END FRAME

mortise hole. Make sure that th e rounded edge of the FRONT SEAT

RAIL is facing up. Place the SEAT brace tenon into theFRONT SEAT

RAIL mortise hole.

STEP-V

Fit the rem aining RIGHT END FR AME mortise holes over and onto

the BACK and FRONT SEAT RAIL tenons. Using a rubber m allet or

regular hammer with a wood block between the hammer and the wood,

drive the tenons and mortise holes together until all the joints fit snugly

together

STEP-VI

Hammer all dowels into their respective joints as shown in the assembly diagrams above.

Please make sure not to hit other parts of the bench. To avoid dim pling the wood, we

suggest that you place a block of wood between the dowel head and the hammer head for

the last few blows. If the dowels are not comple tely flush, use a saw to cut the ends and

then use the sandpaper to sm ooth the tops. Inse rt the brass screws into their respective

pre-drilled SEAT FRAME screw holes (see a ssembly diagram). Do not ham mer in the

screws, but drive them in with a proper screw driver. Insert eye screws into pre-drilled

holes on the outside of the END FRAMES.

IF YOU HAVE ANY QUESTIONS REGARDING THE ASSEMBLY OF YOUR

KINGSLEY-BATE FURNITURE, PLEASE CONTACT THE KINGSLEY-BATE

DEALER NEAREST TO YOU OR KINGSLEY-BATE DIRECTLY. WE THANK FOR

CHOOSING OUR FURNITURE.

*KINGSLEY-BATE WILL NOT TAKE RESPONSIBILITY FOR DAMAGE

0

IF THESE INSTRUCTIONS ARE NOT FOLLOWED PROPERLY

7200 Gateway Court, Manassas, Virginia 20109

Phone: 703-361-7000, Fax: 703-361-7001

1
2
3

AuthenTeak Kingsley-Bate SG30 St. George Assembly Instructions

Kingsley-Bate SG30 St. George

Brand: AuthenTeak

Model: Kingsley-Bate SG30 St. George

Type: Assembly Instructions

AuthenTeak Kingsley-Bate SG30 St. George is a high-quality garden furniture piece that combines durability with elegant design. Constructed from premium teak wood, this 4-foot swing offers a comfortable and inviting seating experience for outdoor relaxation. The swing features a sturdy frame with mortise and tenon joinery, ensuring stability and longevity. Assembly is straightforward, with step-by-step instructions and pre-drilled holes for easy dowel and screw insertion. Enjoy the beauty of natural teak as you unwind in the comfort of your own backyard oasis.

Related papers

Other documents