Hampton Bay 2-6038-52-0WS Installation guide

Brand
Hampton Bay
Model
2-6038-52-0WS
Type
Installation guide

Hampton Bay 2-6038-52-0WS

This Hampton Bay product is a 64" X 40" HIGH DINING TABLE. The table is easy to assemble and comes with all the necessary hardware. It is made of durable materials and is built to last. The table is perfect for both indoor and outdoor use. It is also easy to clean and maintain. It is important to read and understand the instruction manual before assembling or using the table. The table should be assembled by two people. The table should be placed on a nonabrasive surface to avoid scratching.

Hampton Bay 2-6038-52-0WS

This Hampton Bay product is a 64" X 40" HIGH DINING TABLE. The table is easy to assemble and comes with all the necessary hardware. It is made of durable materials and is built to last. The table is perfect for both indoor and outdoor use. It is also easy to clean and maintain. It is important to read and understand the instruction manual before assembling or using the table. The table should be assembled by two people. The table should be placed on a nonabrasive surface to avoid scratching.

Parts List
A
1
12
12
2
12
2
B
C
D
E
F
G
H
1
1
SALEM
64" X 40" HIGH DINING TABLE
Step 2
Attach leg connector bracket (C) to the table legs by inserting bolts (D) with metal washers (E)
through the pre-drilled holes in the leg connector bracket and legs.
Step 3
Using hex wrench (G), tighten all bolts completely and cover them with plastic bolt
caps (F).
Important note: Each bolt should be tightened a few revolutions at a time, alternating
between bolts in a cross corner (X) pattern. This will ensure your table is level by placing equal
pressure on all bolt joints. Do not over tighten.
Step 4
Keep touch-up paint (H) for future use for both your table and chairs.
Your table is now ready for use.
With the help of another person, turn the table in the upright position.
TABLE TOP
TABLE LEG
BOLT (M6x20)
METAL
WASHER
PLASTIC
BOLT CAP
HEX
WRENCH
TOUCH-UP
PAINT
Step 1
With the help of another person, turn table top (A) upside down on a soft surface. Attach table
legs (B) to the table top by inserting bolts (D) with metal washers (E) through the pre-drilled holes
in the legs and into the table top. (DO NOT TIGHTEN THE BOLTS COMPLETELY!)
Step 1
Step 2
IMPORTANT: PLEASE READ COMPLETE INSTRUCTION SHEET PRIOR TO ASSEMBLY!
Identify all parts packed in carton against the parts list. Remove all protective
materials, place parts on a nonabrasive surface to avoid scratching. If any parts
are missing or damaged, DO NOT attempt to assemble. Please contact our
customer service center (Monday-Friday 9:00 a.m.-5:00 p.m.CST) at
1-877-527-0313 or visit our website at www.homedepot.com.
LEG
CONNECTOR
BRACKET
IMPORTANT:
To avoid damage to your table:
- If using an umbrella, an umbrella base must be used at all times.
- Make sure the plastic umbrella safety ring is installed in the center of the table before you
insert the umbrella pole through the table.
- Remove the umbrella from the table when not in use or in the event of wind, rain, hail, sleet,
snow or any other inclement weather.
- In storing patio furniture, do not stack anything on glass, stone, or marble tabletops.
- Before storing, drain all water that may have accumulated in or around patio furniture frames.
If not drained properly, water can cause freeze damage.
- Cover furniture with outdoor furniture covers when not in use.
- For safety reasons, do not sit or stand on the table.
HM-W6440T02
  • Page 1 1

Hampton Bay 2-6038-52-0WS Installation guide

Brand
Hampton Bay
Model
2-6038-52-0WS
Type
Installation guide

Hampton Bay 2-6038-52-0WS

This Hampton Bay product is a 64" X 40" HIGH DINING TABLE. The table is easy to assemble and comes with all the necessary hardware. It is made of durable materials and is built to last. The table is perfect for both indoor and outdoor use. It is also easy to clean and maintain. It is important to read and understand the instruction manual before assembling or using the table. The table should be assembled by two people. The table should be placed on a nonabrasive surface to avoid scratching.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents