Hanover TRADDN6PCSW4BN-SU-R Installation guide

Brand: Hanover

Model: TRADDN6PCSW4BN-SU-R

Type: Installation guide



HanoverOutdoorFurniture



IMPORTANT

Ifyouhaveanyproblemswiththisproduct(missingordamagedparts,assemblyissues,etc.),

PLEASEDONOTRETURNTOTHERETAILER/STORE

fromwhereyoupurchasedtheproduct.

PleasecallourToll‐FreeCustomerServiceHotlineat:

1‐800‐416‐3511

Between9:00AMand5:00PMEasternTime,MondaythroughFriday

Orvisitourwebsiteat:

www.hanover‐products.com



Toexpediteanyfuturewarrantyclaims,pleaseretaintheInstructionSheet,Warranty

Cardandreceiptforfutureuse.

For additionalon‐linesupportonassembly,troubleshootingandcare&maintenanceofyouroutdoor

furniture,pleasevisitourwebsiteat:www.hanover‐products.com. 

6/1/2015(a)

Page 4

*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE

PARTS IDENTIFICATION LIST

AAF06000

PARTS LIST ORDER PART #DESCRIPTION

FOOT CAP

FACTORY ASSEMBLY

FC0030

Page 4

ASSEMBLY INSTRUCTIONS

Attach a leg connector bar to the middle leg by using the bolts and washers as shown in .

Guide the bolts through the holes in the leg connector bar, into the pre-drilled holes in the middle

leg. Repeat for the other leg connector bar.

Hand tighten only 2-3 turns.

igure

Attach a side leg to the leg connector bar by using the bolts and washers as shown in .

Guide the bolts through the holes in the leg connector bar, into the pre-drilled holes in the side leg.

Repeat for the other side leg.

Hand tighten only 2-3 turns.

igure

Attach the assembled base to the seat frame by using the bolts and washers as shown in . Guide

the bolts through the holes in the side legs and middle leg, into the pre-drilled holes in the seat frame.

Hand

tighten only 2-3 turns.

igure

After making any necessary adjustments to the alignment of the , use the hex bolt driver to tighten

all bolts. Repeat until all bolts are tight. Over tightening may strip bolts. Cover

all bolts with covers.

Do not over tighten.

ottoman

F1igure

Figure 2

Figure 3

Page 5

* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE

PARTS IDENTIFICATION LIST

QTY

PARTS LIST DESCRIPTION ORDER PART #

AAL08045

1/4" X 20 MM BOLT

HW0036

Ø6.5 X 1.0 MM

WASHER

HW0004

FOOT CAP

FACTORY ASSEMBLY

FC0030

SEAT FRAME

SIDE LEG

HEX BOLT DRIVER

HW0006

HW0105

BOLT COVER

MIDDLE LEG

LEG CONNECTOR

BAR

AA0729

AA0730

AA0731

AA0732

Page 4

ASSEMBLY INSTRUCTIONS

Place the table upside down on a flat, non-abrasive surface. Attach table leg to the table

rim by using the bolt and washer as shown in . Guide the bolt through the hole in the table leg, into

the pre-drilled hole in the table rim. Repeat for the other three legs.

rim (without glass) a

Fig 1

Hand tighten only 2-3 turns.

Attach a leg to the leg connector bracket by carefully guiding the bolts already in place on the table legs (each

leg has two bolts) through the holes in the leg connector bracket. Add a washer and a nut to the end of each

bolt as shown in . Repeat on the other three legs.Fig 2 Hand tighten only 2-3 turns..

After making any necessary adjustments to the alignment of the table, use the hex bolt driver and hex wrench to tighten

all bolts . each bolt must be tightened a few revolutions at a time. In order to apply equal pressure to all bolt

joints, we recommend working in a cross corner (X fashion). Repeat until all bolts are tight.

Over tightening may strip bolts. Cover all bolts with covers.

Note:

Do not over tighten.

FOOT CAP

With the help of another person, turn the table in the upright position. Note the clear bumpers spaced evenly throughout

the inside of the rim. Carefully place table glass inside the rim, resting on the clear bumpers.

Page 5

*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE

PARTS IDENTIFICATION LIST

ALV35610

UMBRELLA HOLE

RING

FACTORY ASSEMBLY

G0004

PARTS LIST DESCRIPTION ORDER PART #

NUT COVER

BOLT COVER

HEX BOLT DRIVER

HEX WRENCH

1/4" NUT

TABLE LEG

LEG CONNECTOR

BRACKET

GLASS TOP

QTY

HW0027

HW0105

HW0006

HW0009

HW0004

HW0014

FOOT CAP

FACTORY ASSEMBLY

Ø6.5 X 1.0 MM

WASHER

1/4" X 20 MM BOLT

HW0035

TABLE RIM

FC0069

TABLE BUMPER

FACTORY ASSEMBLY

G0199

AT10283

AT10284

AT10285

Hanover TRADDN6PCSW4BN-SU-R Installation guide

Hanover TRADDN6PCSW4BN-SU-R Installation guide

Hanover TRADDN6PCSW4BN-SU-R Installation guide

Related papers

Other documents