EZ-FLO 10671 Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
This manual is also suitable for
Dual Control
Bathroom Faucet
Before You Begin
Check to make sure you have the following:
10671
10673
Tools and Supplies
You will need the following to install your new faucet:
Pipe
Tape
Adjustable
Wrench
With Pop-Up
Phillips
Screwdriver
This product is engineered to meet the EPA
WaterSense flow requirement. The flow rate
is governed by the aerator. If replacement is
ever required, be sure to request Watersense
compliant lavatory faucet aerator to retain the
water conserving faucets of this faucet.
Silicone
Sealant
Shut off main water supply before installation.
Faucet Installation
2 Remove assembled
parts from the faucet body.
8 After installing faucet, remove
aerator and turn on water to remove
any left over debris. Reassemble
aerator and tigthen.
3 Place the spout in the
center hole of sink. Secure
parts as shown above.
4 Remove assembled
parts from the faucet
body.
7 Apply pipe tape onto the threads
of the handle valve body inlet port,
connect supply tube and tighten with
lock nut.
5 Place the handle bodies through the
left and right holes. Re-assemble the
parts and tighten mounting nut.
6 Remove protective cap.Connect handle assembly to the spout body with
water supply hose. Push supply hose adapter with hose coupling until you
hear a "click". Pull hose down to make sure connected firmly.
1 Shut off water supply.
Pop-Up Drain Installation
2 Place a ring of silicone sealant
beneath the lip of the drain collar (3)
and place it in the opening of the sink.
Press down firmly to secure the drain
collar (3).
3 Tighten the rubber washer (4)
and lock nut (5) onto the drain
collar.
Pop-Up Drain Installation
1 Remove the rubber washer (4) and
lock nut (5) from the drain assembly.
4 Connect tail piece on pop-up
drain to waste outlet (not included).
Check all drain connections and P
trap for leaks.
2
1
5
3
Lock nut
Cartridge
Drain collar
Stopper
Rubber washer
4
4.
5.
Keep this manual for ordering replacement parts.
Replacement Parts
Troubleshooting Guide
Minor problems often can be fixed without a plumber. Before doing any work on the faucet, shut off water supply and
close stopper or drain to avoid losing small parts.
noituloSesuaCmelborP
Leak from spout Damaged or dirty seals Disassemble faucet, remove cartridge. Clean or replace
cartridge if necessary. Reassemble.
.
Leak from under handle Damaged cartridge Remove handle. Replace cartridge.
Uneven water spray Clogged aerator Remove aerator. Clean or replace aerator if necessary.
Leak from around aerator Bad aerator seal Remove aerator. Check to see that seal is flat and undamaged.
Replace aerator if necessary.
Water drains slowly or not at all Clogged drain Remove stopper. Remove visible debris.
If still clogged, remove and clean trap. Reassemble.
1.1
2.1
1.2
3.
4.2
9.
5.
6.
7.
8.
2.2
4.1
1.1 Metal Handle Assembly - Cold A602836C
1.2 Metal Handle Assembly - Hot A602836H
2.1 Handle Adapter - Cold A66G378C
2.2 Handle Adapter - Hot A66G378H
3 Retainer Nut A016022
4.1 Ceramic Disc Cartridge - Cold A507104N
4.2 Ceramic Disc Cartridge - Hot A507103N
5 Mounting Hardware Assembly A66D900ZN-H
6 Aerator 1.2 gpm A553058N
7 Mounting Hardware A603233
8 Supply Hose A135141N
9 50/50 Pop-Up Assembly A505219-P
-
1
-
2
-
3
-
4
EZ-FLO 10671 Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI