Page is loading ...
Dual Control
Kitchen Faucet
Before You Begin
Check to make sure you have the following:
10697
10699
Tools and Supplies
You will need the following to install your new faucet:
Groove
Joint Pliers
Pipe
Tape
Adjustable
Wrench
Matching Finish Side Spray
Silicone
Sealant
Shut off main water supply before installation.
1 Shut off hot and cold
water supply to faucet or
turn off main water
supply.
2 Position new faucet.
Insert spray holder
through fourth hole on
sink.
3 Screw and tighten
lock nuts onto faucet and
shank.
4 Insert spray hose into
spray holder.
5 Screw spray head onto
spray hose.
6 Remove the protective cap prior to connecting the quick connect
hose assembly. Attach lower end of spray hose to central supply tube
in facuet.
A. Push quick connect hose assembly firmly upward until unable to
push any further. You will hear a clear "CLICK" sound.
B. Pull down on quick connect hose assembly, if you can not pull off,
then quick connect hose assembly is secure.
C. To remove the quick connect hose assembly, push quick connect
hose assembly upward, then press the clip and housing together
while pulling down at the same time.
Faucet Installation
Protective Cap
7 Securely attach water
supply hoses or tubes onto
inlet ports.
8 Apply pipe tape onto threads
of the water supply. Tighten the
hose onto water supply.
9 After installing faucet, remove
aerator and turn on water to remove
any left over debris. Reassemble
aerator and tighten.
Faucet Installation
Hot
Cold
1 Handle Cap Assembly A66D649
2.1 Metal Handle - Cold A069475C
2.2 Metal Handle - Hot A069475H
3.1 Handle Adaptor - Cold A110114C
3.2 Handle Adaptor - Hot A110114H
4 Retainer Nut Assembly A66D630
5.1 Ceramic Disc Cartridge - Cold A507004N
5.2 Ceramic Disc Cartridge - Hot A507003N
6 Aerator 1.75 gpm A500026N-55
7 Spout Seal A663044N
8 Spout Assembly A666465
9 Spray Diverter A66G391
10 Side Spray A503002N-T
11 Spray Holder Assembly A220008
12 Spray Hose A512139N
13 Sealing kit A66G352N
14 Putty Plate A011003
15 Lock Nut Set A504023
16 Aerator Wrench A031025ZN
Keep this manual for ordering replacement parts.
Replacement Parts
Troubleshooting Guide
Minor problems often can be fixed without a plumber. Before doing any work on the faucet, shut off water supply and
close stopper or drain to avoid losing small parts.
noituloSesuaCmelborP
Leak from spout Damaged or dirty seals Disassemble faucet, remove cartridge. Clean or replace
cartridge if necessary. Reassemble.
.
Leak from under handle Damaged cartridge Remove handle. Replace cartridge.
Uneven water spray Clogged aerator Remove aerator. Clean or replace aerator if necessary.
Leak from around aerator Bad aerator seal Remove aerator. Check to see that seal is flat and undamaged.
Replace aerator if necessary.
Water drains slowly or not at all Clogged drain Remove stopper. Remove visible debris.
If still clogged, remove and clean trap. Reassemble.
Spray is not working Remove cap and unscrew the diverter. Clean or replace it.
Diverter is dirty or broken
1.
2.1
3.1
5.1
6.
7.
14.
8.
9.
12.
13.
10.
11.
2.2
5.2
3.2
4.
15.
16.
/
