EZ-FLO 10717 Installation guide

Brand: EZ-FLO

Model: 10717

Type: Installation guide

This manual is also suitable for

10719

The EZ-FLO 10717 Dual Control Kitchen Faucet with Matching Finish Side Spray is a versatile and reliable addition to your kitchen. Its dual control handles allow for precise adjustment of water temperature and flow, while the matching finish side spray provides a convenient way to rinse dishes or clean the sink. Installation is straightforward, with all necessary tools and supplies listed in the manual. The faucet features a protective cap to prevent damage during installation, and a quick-connect hose assembly for easy connection to your water supply.

Dual Control

Kitchen Faucet

Before You Begin

Check to make sure you have the following:

10717

10719

Tools and Supplies

You will need the following to install your new faucet:

Groove

Joint Pliers

Pipe

Tape

Adjustable

Wrench

Matching Finish Side Spray

Silicone

Sealant

Shut off main water supply before installation.

1 Shut off hot and cold

water supply to faucet or

turn off main water

supply.

2 Position new faucet.

Insert spray holder

through fourth hole on

sink.

3 Screw and tighten

lock nuts onto faucet and

shank.

4 Insert spray hose into

spray holder.

5 Screw spray head onto

spray hose.

6 Remove the protective cap prior to connecting the quick connect

hose assembly. Attach lower end of spray hose to central supply tube

in facuet.

A. Push quick connect hose assembly firmly upward until unable to

push any further. You will hear a clear "CLICK" sound.

B. Pull down on quick connect hose assembly, if you can not pull off,

then quick connect hose assembly is secure.

C. To remove the quick connect hose assembly, push quick connect

hose assembly upward, then press the clip and housing together

while pulling down at the same time.

Faucet Installation

Protective Cap

7 Securely attach water

supply hoses or tubes onto

inlet ports.

8 Apply pipe tape onto threads

of the water supply. Tighten the

hose onto water supply.

9 After installing faucet, remove

aerator and turn on water to remove

any left over debris. Reassemble

aerator and tighten.

Faucet Installation

Hot

Cold

1 Metal Handle A662493

2.1 Handle Extension Assembly - Cold A66G378C

2.2 Handle Extension Assembly - Hot A66G378H

3 Retainer Nut Assembly A66D822

4.1 Ceramic Disc Cartridge - Cold A507104N

4.2 Ceramic Disc Cartridge - Hot A507103N

5 Aerator 1.75gpm A500026N-55

6 Spout Seal Kit A663044N

7 Spout Assembly A666465

8 Spray Diverter A66G391

9 Side Spray A503002N

10 Spray Holder Assembly A220008

11 Spray Hose A512139N

12 Sealing kit A66G352N

13 Putty Plate A011003

14 Lock Nut Set A504023

15 Aerator Wrench A031025ZN

Keep this manual for ordering replacement parts.

Replacement Parts

Troubleshooting Guide

Minor problems often can be fixed without a plumber. Before doing any work on the faucet, shut off water supply and

close stopper or drain to avoid losing small parts.

noituloSesuaCmelborP

Leak from spout Damaged or dirty seals Disassemble faucet, remove cartridge. Clean or replace

cartridge if necessary. Reassemble.

Leak from under handle Damaged cartridge Remove handle. Replace cartridge.

Uneven water spray Clogged aerator Remove aerator. Clean or replace aerator if necessary.

Leak from around aerator Bad aerator seal Remove aerator. Check to see that seal is flat and undamaged.

Replace aerator if necessary.

Water drains slowly or not at all Clogged drain Remove stopper. Remove visible debris.

If still clogged, remove and clean trap. Reassemble.

Spray is not working Remove cap and unscrew the diverter. Clean or replace it.

Diverter is dirty or broken

2.1

4.1

14.

12.

13.

10.

11.

4.2

15.

2.2

EZ-FLO 10717 Installation guide

Brand: EZ-FLO

Model: 10717

Type: Installation guide

This manual is also suitable for

10719

Download PDF

report

EZ-FLO 10717 Installation guide

This manual is also suitable for

EZ-FLO 10717 Installation guide

Related papers

Other documents