MULTIPLEX Icepic Micro Switch Bracket Kit (020003728) Installation guide

MULTIPLEX
Brand
MULTIPLEX
Model
Icepic Micro Switch Bracket Kit (020003728)
Type
Installation guide

This manual is also suitable for

MULTIPLEX Icepic Micro Switch Bracket Kit (020003728) is a replacement part designed for use with MULTIPLEX Icepic MDH-302/402 ice machines. This kit includes a chute mount bracket, screws, nuts, and instructions. It is used to replace the existing micro switch bracket on the ice crusher assembly. The new bracket must be aligned with the hole locations of the previous bracket and mounted using a Phillips screwdriver. The electrical terminals must then be reconnected to the micro switch on the new bracket.

MULTIPLEX Icepic Micro Switch Bracket Kit (020003728) is a replacement part designed for use with MULTIPLEX Icepic MDH-302/402 ice machines. This kit includes a chute mount bracket, screws, nuts, and instructions. It is used to replace the existing micro switch bracket on the ice crusher assembly. The new bracket must be aligned with the hole locations of the previous bracket and mounted using a Phillips screwdriver. The electrical terminals must then be reconnected to the micro switch on the new bracket.

Instructions
Manitowoc Beverage Systems Sellersburg, 2100 Future Drive, Sellersburg, IN 47172, Tel: 812-246-7000, www.manitowocbeverage.com
020003728
8/11
Subject: Icepic MDH-302/402 Micro Switch Bracket Kit
Tools Required
• #2 Phillips Head Screwdriver
INSTALLATION OF KIT
Remove Medallion & Chute Rod
1. Remove power from unit
2. Remove the two knurled screws from either the right or left side of
the merchandiser frame starting with the bottom one first and
remove the end portion of the frame that holds the medallion into
the merchandiser. (See Figure 1)
NOTE: A Phillips head screw driver may be used if the screws are
too tight.
3. Slide the two clear plastic sheets out of the frame channels
keeping the medallion sandwiched in between. (See Figure 1)
4. Remove the cotter pin from the chute rod and slide the rod to the
left, removing it from the ice crusher assembly.
(See Figure 2)
Replace Micro Switch Bracket
5. Disconnect the terminals from the micro switch and remove the
bracket using # 2 Phillips screw driver. (See Figure 3)
6. Line up the new bracket assembly to the hole locations the
previous bracket used and mount the to the crusher assembly
using a # 2 phillips screw driver. (See Figure 3)
7. Reconnect the electrical terminals to the micro switch on the new
bracket. (See Figure 3)
Reinstall Rocking Chute Pin
8. Slide the chute rod through the chute and crusher assembly by
inserting it into the left side of the ice chute and pushing it to the
right. (See Figure 4)
9. Push the cotter pin removed in step 4 back into the chute rod to
lock it into place. (See Figure 4)
NOTE: See page 2 for micro switch adjustment.
KIT 020003729 CONTENTS
QTY DESCTRIPTION PART NUMBER
1 Chute Mount Bracket 020003704
2 Screw 6-32 X 1 IN SS 0900901
2 Nut 6-32 ESNA SS 0902304
1 Instructions 020003728
FIGURE 4 - Completed Installation of New Bracket
FIGURE 1 - Medallion Removal
Ice Chute Pin
FIGURE 2 - Remove Ice Chute Pin
Micro Switch
Terminals
FIGURE 3 - Bracket & Micro Switch Replacement
Micro Switch
Bracket
Micro Switch
Terminals
Bracket
Remove Existing Bracket
Screws
Install New Bracket
Screws
Ice Chute Pin
Cotter Pin
Location
Icepic MDH-302/402 Micro Switch Bracket Kit 020003728 8/11
Manitowoc Foodservice Sellersburg, 2100 Future Drive, Sellersburg, IN 47172, Tel: 812-246-7000, www.manitowocbeverage.com
Adjust Micro Switch
10. The switch arm is pre-adjusted to line up with the top of the ice
chute. If adjustment is needed this can be done by loosening the
microswitch adjustment screw with a phillips head screwdriver
and sliding the micro switch up or down until in proper position.
(See Figure 5)
11. Once in proper position retighten the adjustment screw.
Reinstall Medallion & Power
12. Slide the graphic medallion back into the merchandiser by
positioning the plastic sheets into the channels on the
merchandiser frame exposed in step 2.
13. Slide the medallion down the frame channels into the
merchandiser ensuring that the graphic medallion remains
sandwiched between the two plastic sheets.
14. Restore power to the unit.
Important
The micro switch arm must be touching the top of the ice
chute after the new bracket has been tightened into place
in order for it to engage correctly.
FIGURE 5 - Micro Switch Adjustment
Micro
Switch Arm
Micro
Switch
Adjustment
SCrew
FIGURE 6 - Reinstall Medallion
Micro
Switch
Top of Ice
Chute
  • Page 1 1
  • Page 2 2

MULTIPLEX Icepic Micro Switch Bracket Kit (020003728) Installation guide

MULTIPLEX
Brand
MULTIPLEX
Model
Icepic Micro Switch Bracket Kit (020003728)
Type
Installation guide
This manual is also suitable for

MULTIPLEX Icepic Micro Switch Bracket Kit (020003728) is a replacement part designed for use with MULTIPLEX Icepic MDH-302/402 ice machines. This kit includes a chute mount bracket, screws, nuts, and instructions. It is used to replace the existing micro switch bracket on the ice crusher assembly. The new bracket must be aligned with the hole locations of the previous bracket and mounted using a Phillips screwdriver. The electrical terminals must then be reconnected to the micro switch on the new bracket.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents