Valco baby car seat adaptor Operating instructions

Brand: Valco baby

Model: car seat adaptor

Category: Strollers

Type: Operating instructions

This manual is also suitable for

Car Seat Adapter

Valco baby car seat adaptor allows you to attach compatible car seats to your Valco Trimode Single or Twin Trimode Stroller. It is compatible with Graco, Peg Perego, and Britax car seats. The adaptor is easy to install and remove, and it comes with tether straps to ensure that the car seat is securely attached to the stroller. With this adaptor, you can easily and conveniently transport your child from the car to the stroller.

Thank you for purchasing a quality VALCO product. Please read and follow the instructions outlined in this

guide carefully. Familiarise yourself with the construction and safety features; be sure that you understand all

the warnings and safety guidelines before use.

Retain this guide in a safe place for future reference.

PRODUCT REFERENCE GUIDE

GRACO/PEG PEREGO/BRITAX CAR SEAT ADAPTOR

Due to our policy of continuous product

development, this product is constantly

evolving. It is possible that some features

or procedures outlined here have changed

since this document was written. If you are

unsure of any procedure shown here, please

or Canada customers can email canada@

valcobaby.com to obtain the most up to date

information before use. Include the batch

number, which can be found on a sticker on

the frame.

All pictures and diagrams herein are provided

for illustration purposes only. Actual product,

color or fabric may vary. VALCO reserves the

right to modify or alter any specication or

color without notice or obligation to modify

any product previously purchased

FURTHER INFORMATION

In North America only

www.valcobaby.com

1800 610 7850

In Canada only

416 488 1900

FOR USE WITH GRACO

SINGLE/TWIN

CAR SEAT ADAPTOR:

If you haven’t already done so, remove

the front bar or plugs from the nylon

housings on either side of the stroller

frame by pressing each inner ‘release

button’ and lifting the front bar or plug

from the housing.

Insert the car seat adaptor connecting

pieces into the nylon housings.

Be sure that the bar release button is

securely in the housing.

Located on the car seat adaptor

support frame are two sets of tether

straps. The rst set (as shown in Figure

C) rest on the foot rest of the stroller.

Adjust these straps so they wrap

underneath the foot rest of the stroller.

Secure by inserting the male clip into

the female end.

Ensure these straps are as tight as

possible.

To secure the Twin Adaptor see Page 3

‘Secure the Twin Adaptor’.

The following instructions are for the Valco Baby

TriMode Models:

Insert the Adaptor

Secure the Adaptor

Remove Bumper Bar or Housing

Bumper Bar

Nylon Plug

press

Position the Car Seat so that the infant

is facing the handlebar of the stroller.

Line up the Car Seat to the Adaptor

frame ensuring that the Car Seat latch

(red lever on back of car seat) rests

under the Adaptor frame.

Once the car seat is in position, take

the second set of tether straps and

place them through the sides of the car

seat, (where a seat belt would go) and

connect via the buckle.

Ensure that the strap is tight and

securely fastened by pulling on the free

end of the strap.

TO REMOVE THE CAR SEAT:

Detach the straps (reversing the process

outlined in E) and lift up the RED LEVER

located on the back of the car seat.

TO REMOVE THE ADAPTOR:

Detach the straps secured beneath the

footrest.

Locate the two nylon release buttons

that sits below the frame at each side of

the stroller.

Press the release button and lift the

adaptor bar out of the nylon housings.

Insert the Car Seat

Remove Adaptor

Secure the Car Seat

TO SECURE TWIN CAR SEAT

ADAPTOR:

replace step c in single

adaptor instructions with the

following two steps c-1 and

c-2:

Located on the Car Ceat Adaptor

support frame are two sets of tether

straps. The rst set (as shown in Figure

C-1- 1 )rest on the foot rest of the

stroller.

To secure these straps;

Lift up the footrest ap (Figure C-1- 2 )

and insert the Male clip through the slit

in the stroller frame directly above the

footrest (Figure C-1- 3 ).

Wrap the Female clip around the

closest side of the stroller, meeting the

Male clip underneath the footrest of the

stroller.

Insert the Male clip into the Female clip,

and secure.

continue to follow the single

graco car seat adaptor

instructions step d to f.

FOR USE WITH PEG PEREGO

SINGLE/TWIN

CAR SEAT ADAPTOR:

If you haven’t already done so, remove

the front bar or black plugs from the

nylon housing at either side of the

stroller frame by pressing each inner

“release button” and pulling the front

bar/plug upward.

Remove Bumper Bar or Housing

Bumper Bar

Nylon Plug

press

Secure the Twin Adaptor

C 1

Secure the Twin Adaptor

Insert the Adaptor

Insert the Car Seat

Insert the car seat adaptor connecting

pieces into the nylon housings.

Be sure that the bar release button is

securely in the housing.

Position the Car Seat so the infant is

facing the handlebar of the stroller.

There are three bars on the adaptor

frame corresponding to the three slots

in the bottom of the car seat. Line

these up, and push the car seat until it

locks into the frame.

Once the car seat is in position, thread

the tether straps through the sides of

the car seat, (where a seat belt would

go) and connect the buckle.

HINT: You may have to unsnap the

snaps on the side pockets of the car

seat to locate the slots.

Ensure that the strap is tight and

secure by pulling on the free end of the

strap.

Secure the Car Seat

Insert Car Seat Adaptor

Remove Bumper Bar or Housing

Bumper Bar

Nylon Plug

press

TO REMOVE THE CAR SEAT:

Detach the straps (reversing the

process outlined in D) and lift up the

car seat to unlock it from the frame.

TO REMOVE THE CAR SEAT ADAPTOR:

Locate the two nylon release buttons

that sit below the frame at each side of

the stroller.

Press the release button and lift the

adaptor bar out of the nylon housings

FOR USE WITH BRITAX

SINGLE/TWIN

CAR SEAT ADAPTOR:

If you haven’t already done so, remove

the front bar or plugs from the nylon

housings on either side of the stroller

frame by pressing each inner ‘release

button’ and lifting the front bar or plug

from the housing.

Insert the car seat adaptor connecting

pieces into the nylon housings.

Be sure that the bar release button is

securely in the housing.

TWIN ADAPTOR HINT:

When positioning the adaptor, make

sure that the raised end of the adaptor

bar will be resting in the seat portion of

the stroller when connected.

Remove Adaptor

Secure the Car Seat

Remove Adaptor

Position the Car Seat so that infant is

facing the handlebar of the stroller.

Line up the Car Seat to the Adaptor

frame ensuring that the Car Seat latch

has clicked on the Adaptor frame.

Once the car seat is in position, thread

the tether straps through the sides of

the car seat, (where a seat belt would

go) and connect the buckle.

Ensure that the strap is tight and

secure by pulling on the free end of the

strap.

TO REMOVE THE CAR SEAT:

Detach the straps (reversing the

process used in D) and lift up the car

seat to unlock it from the frame.

TO REMOVE THE CAR SEAT ADAPTOR:

Locate the two nylon release buttons

that sit below the frame at each side of

the stroller.

Press the release button and lift the

adaptor bar out of the nylon housings.

Insert Carseat

warnings

Your child’s safety is your responsibility ………

Check all parts for breakage or fatigue before use. Discontinue immediately •

if any part is found to be damaged or broken.

Do not use this Car Seat Adaptor until you have read and understood all of •

the instructions.

warning:• Please be aware that this instruction manual is strictly for

the Valco Car Seat Adaptor. Please know and understand the Car Seat

manufacturers instructions before use.

This adaptor is compatible for use with Graco/Peg Perego/Britax car seats •

accordingly. DO NOT use with any other brand.

Only use this adaptor with the correct model Valco Trimode Single or Twin •

Trimode Stroller accordingly.

Never leave your child unattended. •

alwaYs• check that the Car Seat Adaptor bar, as well as the Car Seat, are

securely fastened.

alwaYs• ensure that child is clear of all moving parts when adjusting the

stroller.

warning:• Avoid serious injury from falling or sliding out. Make sure

that the child is harnessed into the Car Seat using the manufacturer’s

instructions, at all times.

This product is intended for use with infants whose Weight is: 5 - 30 lbs and •

Height: under 30 inches. Excessive weight may cause a hazardous unstable

condition to exist.

Parcels, accessory items or both that are placed on the unit may cause the •

unit to become unstable.

Do not use accessories not designed for your stroller as they may be •

unsafe.

This product is intended for domestic use only. It is not intended for •

commercial use.

North America

www.valcobaby.com

In USA only

1 800 610 7850

In Canada only

416-488-1900

Valco baby car seat adaptor Operating instructions

Brand: Valco baby

Model: car seat adaptor

Category: Strollers

Type: Operating instructions

This manual is also suitable for

Car Seat Adapter

Download PDF

report

Valco baby car seat adaptor Operating instructions

This manual is also suitable for

Valco baby car seat adaptor Operating instructions

Related papers

Other documents