SHYAM Networks WE100 Quick start guide

Brand
SHYAM Networks
Model
WE100
Type
Quick start guide
NETWORKS
www.shyamnetworks.com
WE100
Outdoor Wi-Fi AP/CPE
Quick Start Guide
For advanced settings and more detailed information, download the user
manual from www.shyamnetworks.com.
Package Contents
WE100 (main unit) 1
PoE Adapter 1
Ethernet Cable 1
Quick Start Guide 1
Optional
Table Top
Stand
Self Tapping
Screw
Plastic
Gitti
Worm Drive
Clamp
NETWORKS
WE100
2
MODEL Tx POWER LAN PORT
WE-1C-WM-17 17 dBm 1
WE-1C-WM-22 22 dBm 1
INTERFACE DESCRIPTION
Clamps • Center clamp for pole mounting.
• Top and bottom for wall mounting.
LEDs Indicates the working status.
LAN Port Provides connection through Cat5e cable.
RESET • Single press reboots the system.
• Press till all lights go off once, restores to factory
default settings.
Table Top Stand Provided for table mounting.
Available Models
Interface Description
1. Hardware Overview
Clamps for
Wall Mount
Clamp for Pole Mount
RESET Button
Table Top Stand
WE-1C-WM-17
LEDs
LAN Port
WE100
NETWORKS
3
LED Behavior
LED COLOR STATUS DESCRIPTION
PWR Green On WE100 is powered-on.
Off WE100 is powered-off.
WAN Green On Link is up.
Blinking Data transfer taking place.
Off No link present.
WLAN Green Blinking Indicates that the wireless mode is enabled.
By default, this LED glows.
RSSI Low Green On Indicates that the power level received by
the antenna is low.
RSSI Low + Medium Green On Indicates that medium power level received
by the antenna.
RSSI Low + Medium
+ High
Green On Indicates that high power level is received
by the antenna.
Caution and Warnings
• Use the PoE adapter included with the product. Using a different PoE adapter may
damage the product.
NETWORKS
WE100
4
2. Installing WE100 CPE
STEP 1 Connect one end of an RJ45 Ethernet cable to the LAN OUT port of the PoE
adapter and the other end to LAN of WE100 CPE.
STEP 2 Connect the second RJ45 Ethernet cable attached to the PoE adapter to a network
device,suchastoaswitchortothesystemyouusetocongureWE100CPE.
STEP 3 Connect the PoE adapter to the main electrical supply using the power cord
provided with the PoE adapter kit. Now, turn on the power supply. PWR LED on
the back side of the unit glows. This indicates that WE100 CPE is receiving
power through the PoE adapter and that the connection between WE100 CPE
and your network has been established.
iNote: In case any LED does not operate, then refer to the “Quick Troubleshooting” section.
Congratulations! The installation of WE100 CPE is complete.
WE100 CPE
Pole
PoE AdapterSwitch
Pole
AP25
Computer
WE100
NETWORKS
5
3. WE100 CPE Mounting Instructions
STEP 1 Connect the RJ45 Ethernet cable to WE100 CPE
attached to the PoE adapter.
STEP 2 Placethetabletopstandonthedesiredatsurface.
STEP 3 Insert the WE100 CPE unit inside stand.
STEP 1 Connect the RJ45 Ethernet cable to WE100 CPE
attached to the PoE adapter.
STEP 2 Nail the plastic gittis in wall at proper position aligning
with WE100 CPE screw holes.
STEP 3 Screw the self tapping screws inside the plastic gittis.
STEP 4 Mount WE100 CPE over the self tapping screws.
Table Top
Wall Mounting
Pole Mounting
STEP 1 Connect the RJ45 Ethernet cable to WE100 CPE
attached to the PoE adapter.
STEP 2 Place WE100 CPE on the pole at proper position.
STEP 3 Attach the worm drive clamp to WE100 CPE along with
the pole and tighten it.
NETWORKS
WE100
6
4. Configuring WE100 CPE
STEP 1 Power-up WE100 CPE.
STEP 2 CongureyoursystemwithIPaddressbetween192.168.1.2 to 192.168.1.253
and subnet mask to be 255.255.255.0.
STEP 3 Type the http://192.168.1.1 URL in the Internet Explorer 6.0 or above version to
access the web interface.
STEP 4 Provide user name as admin and password as password.
STEP 5 Click Setup Wizard in the navigation panel to view the Setup Wizard page.
Please refer to “WE100 Conguration and User Guide” for more details.
WE100
NETWORKS
7
5. Quick Troubleshooting
PROBLEM PROBABLE REASON RESOLUTION
The WLAN LED is not
blinking when WE100
CPE is powered-up.
The WAN connectivity
is down.
Check if all cables are
plugged properly.
The LED
corresponding to a
specicportis‘Off’.
WE100 CPE has no power. • Ensure that the power cord is
properly connected WE100 CPE.
• Ensure that the PoE adapter
is properly connected to the
functioning power outlet.
• Ensure that you are using the
same PoE adapter supplied
with WE100 CPE.
iNote: If none of the above
works, press the RESET button
on WE100 CPE to restore the
factory default settings.
NETWORKS
WE100
8
Warranty
This warranty is valid upto 12 months from the date of purchase.
Any manufacturing defect will be repaired by the company free of charge within the period of
warranty subject to the following conditions:
1. Thiswarrantycardmustbedulylledin,stamped&signedbythedealer.Thecardandthe
relevantcashmemomustbepreserved&producedalongwiththedefectiveunit.
2. Once the defective unit is repaired during the said warranty period, the warranty shall thereafter
continue only for the unexpired period to the original warranty.
3. This warranty is not valid for
• Damage resulting from accidents, mishandling, negligence, tampering, unauthorized repair,
failuretofollowinstructions,lightning,reandactofGod.
• Items not purchased from Authorized Dealers of the Company.
• Batteries (including rechargeable) wherever applicable.
• Damage to the tamper proof seal.
4. In case of a problem with your unit, please contact Customer Care. In the event that you are
advised to send and collect the unit from the Service Center of the Company – the same will be
done at your expense.
5. While Company or its Authorized Service Dealer will make every effort to carry out repairs under
this warranty as soon as possible, it is expressly made clear that the company shall not be held
liable for any direct or indirect loss to user due to delay in providing this service.
6. This warranty excludes every condition/warranty/liability not expressly set out therein.
7. Claims, if any to this warranty shall be subject to the courts having jurisdiction in Delhi, India.
Product ______________________________________________________________________
Model No. _______________________________ Serial No. ___________________________
Dealer’s Stamp & Signature
Customer Care,
Shyam Networks (A Division of Vihaan Networks Ltd.)
21-B, Sec-18, Udyog Vihar, Gurgaon-122015
Haryana, India
Email: customer.car[email protected]
All India Helpline No. - +91 124 309 2000 Ext. 2009,
+91 9873573710
Manufactured by Vihaan Networks Ltd. Gurgaon, Haryana, India
109.00016.00
SN/QS/WE100/06/11/R2
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

SHYAM Networks WE100 Quick start guide

Brand
SHYAM Networks
Model
WE100
Type
Quick start guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents