Page is loading ...
ASSEMBLY & OPERATING INSTRUCTIONS
92793
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web Site at www.harborfreight.com
Copyright
©
2005 by Harbor Freight Tools
®
. All rights reserved. No portion of this manual or
any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions and replacement parts please call 1-800-444-3353.
®
CANDLE WALL LANTERN
SKU 92793 For technical questions please call 1-800-444-3353. Page 2
THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please
complete the owner’s record below:
Model______________ Serial No._____________ Purchase Date_______________
SAVE THE RECEIPT, WARRANTY AND THESE INSTRUCTIONS. It is important that you read the
entire manual to become familiar with the unit BEFORE you begin assembly.
Technical Specifications
Material: Wrought iron hanging stand and all brass candle lantern.
Finish: Flat black powder coat
Candle Size: 1-1/2” diameter (not included)
Overall Size: 6-7/8” Hex x 12-1/4” Height.
Weight: 1.25 Lbs.
Safety Warnings and Precautions
WARNING: When using product, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.
Read all instructions before using this product!
1. Keep work area clean. Cluttered areas invite injury.
2. Observe work area conditions. Keep work area well lit.
3. Check for damaged parts. Before using any product, any part that appears damaged should
be carefully checked to determine that it will operate properly and perform its intended function.
Check for any broken or damaged parts and any other conditions that may affect its operation.
Replace or repair damaged or worn parts immediately. Do not use this product if any switch
does not turn on and off properly.
4. Replacement parts and accessories. When servicing, use only identical replacement parts.
Use of any other parts will void the warranty.
5. Always check hardware and assembled parts after assembling. All connections should be
tight and hardware tightened.
6. Keep children and pets away. Children must never be allowed to play with the Wall Lantern.
Only locate this product in an area that is out of reach of children and pets.
7. Store idle equipment. When not in use always lock up the Candle Wall Lantern and keep it out
of the reach of children.
8. Dress properly. Wear restrictive hair covering to contain long hair.
9. Use eye protection. Always wear ANSI approved impact safety goggles when setting up this
product.
10. Maintain products with care. Keep the glass clean for better and safer performance.
11. Do not overreach. Keep proper footing and balance at all times.
SKU 92793 For technical questions please call 1-800-444-3353. Page 3
12. Use the right product for the job. There are certain applications for which this Wall Lantern
was designed. Do not modify this Wall Lantern and do not use this Wall Lantern for a purpose
for which it was not intended.
13. Do not use the Wall Lantern if under the influence of alcohol or drugs. Read warning
labels on prescriptions to determine if your judgement or reflexes are impaired while taking
drugs. If there is any doubt, do not use the Wall Lantern.
14. The Wall Lantern must be used as a complete unit; the stand must be used with the
housing for stability.
15. The Wall Lantern must be hung at least 2 feet from the ceiling and any curtains or drapes
to reduce the chance of fire damage from the candle.
16. Never leave a burning candle unattended. Never leave a candle burn through the night.
17. Do not use the Wall Lantern near any combustible materials or flammable gasses or
liquids.
18. Do not touch the hot glass while in use. Make sure glass is cool to the touch after candle is
extinguished, before touching glass.
19. WARNING: The brass components of this product contain lead, a chemical known to the State
of California to cause birth defects (or other reproductive harm). (California Health & Safety
code § 25249.5,
et seq.
)
WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood by
the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
Unpacking
When unpacking the Candle Wall Lantern, check to make sure the following parts are included. If
any parts are missing or broken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353.
Assembly/ Operation
Your Candle Wall Lantern will require some easy assembly. It is important that you read the entire
manual to become familiar with the product BEFORE you use the Wall Lantern. Before operating the
Wall Lantern be sure that you have all parts described in the Parts List and Assembly Diagram
located on the last page of this manual.
1. Thread the Wall Lantern (1) onto the Wall Stand (2) as shown in the Assembly
diagram.
2. Locate the ideal location for your Candle Wall Lantern. To avoid possible damage from
melted candle wax, it is recommended that the Candle Wall Lantern not be located
over a carpeted area. Always take precautions to prevent melted candle wax from
damaging floor and other surfaces below the Wall Lantern.
3. The Wall Lantern must be hung by the round ring located at the very top of the Wall
Stand (2). Set a screw into the drywall and into a stud. Make certain that the path of the
screw is clear of any electrical lines, wires or lines. Hang the Wall Lantern from this screw.
The Candle Wall Lantern must be used as one unit with the Wall Lantern with Windows (1)
attached to the Wall Stand (2). The Candle Wall Lantern must be hung against a wall to
provide stability.
SKU 92793 For technical questions please call 1-800-444-3353. Page 4
Operation
1. Open the latch located on the Wall Lantern (1) by lifting it and pulling the door open.
2. Set a votive candle (not included) into the candle holder located inside of the Wall
Lantern (1). The candle size must be 1-1/2” diameter to fit into the candle holder
3. Using a Fireplace match or a long length lighter, light the votive candle (not included).
4. Close the door of the Wall Lantern (1) and set the latch. Never leave a burning candle
unattended.
5. Caution: The Candle Wall Lantern will become hot to the touch while a candle is lit.
Maintenance
1. Clean regularly with a damp towel. Do not use any type of solvent for cleaning. Be careful of
the delicate glass enclosure while cleaning. Dry thoroughly.
Parts List
Part # Description Quantity
1. Wall Lantern with Windows 1
2. Wall Stand 1
Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
Hang Candle Wall Lantern
from this ring.
1
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE
TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY
KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
2
/
