Page is loading ...
Technical Specifications
3
Base Width 39.6” min. - 74” max.
Duty Cycle 10% Max. 2 mins on, 18 mins off
Height Range 23.5” - 49” (without table top)
Minimum Table Top Size 43"x 24”
Weight Capacity 330 lbs (110 lbs Per Leg)
Features Soft start/stop, adjustable leveling studs & 4 memory presets
Input Voltage 120 VAC, 60 Hz
Output Voltage 24 VDC
Stroke 25.5"
Speed 1.50"/sec
Material Steel
Certification UL
STEP 3
Frame 1 (2) should be placed on the side of the desk
where you are planning to mount the Control Box (15).
Slide the Control Box into the Frame (2)
STEP 2
Take a Side Bracket (4) and slide it into a Frame (5).
Insert two M6x14 Machine Screws (14) through the
two holes in the top of the side bracket going into the
assembled frame end/leg. Using the supplied Allen
Wrench, rotate each screw just a few turns. After both
screws are inserted, tighten them.
Do the same for the other assembled frame end/legs.
Assembly Instructions
5
STEP 4
Slide the two Center Rails (7) into the two Frames (2 & 5).
Ensure that the slots in the Center Rails face inward and
that they are closer to the top edge when the assembly is
upside down (see image below).
Lock the position of the Center Rails (7) using eight M6x10
Machine Screws (13).
STEP 1
Place one of the Legs (9) into the Frame 3 (5) and
line up the holes. Using the supplied Allen Wrench,
insert four M6x10 Machine Screws (13) through the
holes in the Frame (5), going through into the Leg (9)
and rotate each screw just a few turns. Once all four
screws are inserted, tighten them.
Do the same for the other Legs (9) and the other
Frames (2 & 3).
STEP 6
Lock the position of the Center Rails (7) using eight
M6x10 Machine Screws (13) as shown in the image
below.
Assembly Instructions
STEP 5
Using four M6x10 Machine Screws (13), link the
assembled Frame 2 (3) and Frame 1 (2) as shown in
the image below.
6
STEP 7
Attach each Foot (6) with four M6x14 Machine
Screws (14) and tighten them in a cross-pattern.
STEP 8
We recommend using two people for this step. Turn
the fully assembled table lift set right-side up. Make
sure to grab the table lift by the legs when turning it
over.
STEP 9
Plug the Power Cord (17) into a 110V outlet.
IMPORTANT
You must reset the desk prior to use:
To reset you must press and hold the DOWN button on
the Handset (18) until the table lift reaches its lowest point.
Release the DOWN button. Press and hold the DOWN
button again until the LED display shows "RST". If you are
not using an LED hand remote hold the DOWN button for
10 seconds. Release the DOWN button. Finally press and
hold the DOWN button once more until the desk lowers,
slightly rises then stops. Release the DOWN button and
your desk is now ready to use.
To program up to four presets with the remote just use the
Up/Down buttons to find your desired height, then press
the “M” button followed by a number 1-4.
Once a preset button is pressed, the desk will move to the
programmed height. Make sure no obstacles are in the
desk's path or in contact with any walls.
7
Reset Procedure
Operational Procedure
Once your table lift is installed, operation is simple. Using the wired remote will allow full control over
extending and retracting the lift columns. Use the up button to raise the table lift and the down button
to lower the table lift.
You can program up to 4 locations using the memory setup: Use the up/down buttons on the remote to
find your desired height(s), then press “M” followed by a number 1-4. The table height position is now
saved. To move to the set position, hold the number button.
IMPORTANT
You must reset the desk prior to use:
To reset, press and hold the DOWN button on the Hand Remote (7) until the table lift reaches its
lowest point. Release the DOWN button. Press and hold the DOWN button again until the LED display
shows "RST". If you are not using an LED hand remote hold it for about 10 seconds. Release the
DOWN button. Finally Press and hold the DOWN button once more until the table lift lowers, slightly
rises then stops. This signals the end of the reset procedure. Release the DOWN button and your
table lift is now ready to use.
Troubleshooting
If your desk is not functioning it might need to be reset. Follow the RESET procedure.
If your hand remote has an LED display and it displays "RST" (reset), perform the reset procedure.
If the LED displays shows an error message ("Er1" - "Er13"), confirm that all wired connections are
secure. Then perform the reset procedure.
If the LED remote displays "HOT", let the unit cool down for 20 minutes.
If the error message persists after the reset procedure, contact us at 1-800-676-6123 or
/
