Aventura FBR-1VS-RX User manual

Brand: Aventura

Model: FBR-1VS-RX

Category: Network media converters

Type: User manual

This manual is also suitable for

AventuraTechnologies

180AdamsAvenue

Hauppauge,NY11788

(877)707‐9600

www.aventuratechnologies.com

Instruction Manual

One Channel Video Transmitters and Receivers

Model Numbers:

FBR-1VS-TX – Transmitter, Single-mode Fiber

FBR-1VM-TX – Transmitter, Multimode Fiber

FBR-1VS-RX – Receiver, Single-mode Fiber

FBR-1VM-RX – Receiver, Multimode Fiber

INSTALLATION AND OPERATION INSTRUCTIONS

FUNCTIONAL DESCRIPTION

The FBR-1V(M/S)-TX and FBR-1V(M/S)-RX operate as a transmitter / receiver pair for the

transmission of one baseband NTSC or PAL video signal, over a single multimode or single-mode fiber.

The FBR-1V(M/S)-TX converts one video input, to an optical fiber output.

The FBR-1V(M/S)-RX converts an optical fiber input into one video output.

These units are contained in compact and rugged steel housings with internal dc voltage regulation. The

detachable terminal blocks and LED indicators provide for easy installation and monitoring of video,

optical link, and dc power.

The units operate either surface mounted as modular, stand-alone units, or within a rack mounted card

cage.

INSTALLATION

THE INSTALLATION OF THIS UNIT SHOULD BE MADE BY A QUALIFIED SERVICE

PERSON(S) AND MUST CONFORM TO ALL LOCAL CODES.

The general connectivity of the units is detailed in Figure 1.

Mount the unit to a secure surface using #8 (3mm) hardware in four places. See Figure 2 for a full size

mounting template. Be sure to allow sufficient room for the required minimum bend radius of the fiber

cable used.

POWER SOURCE

The unit requires a +12VDC power source for proper operation. The DC input is diode protected against

reverse polarity connection.

In the USA and in Canada, for standalone surface mounted installation, an Aventura Technologies FBR-

PSUS12DC1A is supplied with this unit. Contact Aventura Technologies for ordering power supply

units for use in countries other than the USA and Canada.

When installed in a rack mounted card cage, the power for the unit is supplied from the card cage’s

power supply.

POWER CONNECTION

Power is supplied to the unit via a two pin, detachable terminal block connector. Follow the labeling on

the unit for proper connections of the +12 volt dc and ground leads.

VIDEO INPUT/OUTPUT CONNECTION

The video input and output connections are made via BNC connectors on the front of the units. The

video inputs and outputs are 75 ohms. For proper operation, the video outputs must be terminated with

75 ohms. For optimum performance, the use of the shortest practical length of coax cables is

recommended.

FIBER CONNECTION

The fiber optic connections are made via ST (multimode fiber) or FC (single-mode fiber) connectors,

located on the rear of the units.

STATUS INDICATORS

The unit provides the following LED status indicators to aid in installation and troubleshooting:

POWER INDICATOR

A bi-color LED indicator monitors the voltage at the module’s power input connector and the operating

internal voltage of the module. The power status associated with this LED is summarized below.

Power Indicator Power Status

Green Proper Input Voltage Present – Proper Internal Operating Voltage Present

Red Proper Input Voltage Present – Internal Operating Voltage Faulty

Off No Input Voltage Detected

OPTICAL LINK INDICATOR

A bi-color LED indicator monitors the power of, and proper synchronization with the optical input

signal that is being received at the FBR-1V(M/S)-TX and/or FBR-1V(M/S)-RX. The Optical Link

status associated with this LED is summarized below.

Optical Link Indicator Optical Status

Green Proper Optical Input Present

Red Optical Input Not Detected

Off Check Power Supply

VIDEO INPUT INDICATOR

A bi-color LED indicator for the video input channel of the FBR-1V(M/S)-TX monitors the status of

the video input. The video input status associated with this LED is summarized below.

Video Input Indicator Video Input Status

Green Proper Video Input Present

Red Video Input Not Correct (Wrong Level or Polarity)

Off No Video Input Detected

Figure 1 – General Connectivity of Units

Figure 2 – Surface Mounting Template (1:1)

LIMITED LIFETIME WARRANTY INFORMATION

This limited lifetime warranty applies only to the original end user customer of the product for so long

as the original end user customer owns the product. This limited warranty is non-transferable.

Damage due to shipping the products to you is covered under this limited warranty. Otherwise, this

limited warranty does not cover damage due to external causes, including accident, abuse, misuse,

problems with electrical power, servicing not authorized by Aventura Technologies, Inc., usage not in

accordance with product instructions, failure to perform required preventive maintenance, and problems

caused by use of parts and components not supplied by Aventura Technologies, Inc.

During the warranty period beginning on the invoice date, Aventura Technologies, Inc. will repair or

replace products covered under this limited warranty that are returned to Aventura Technologies, Inc.'s

facility. To request limited warranty service, you must contact Aventura Technologies, Inc.'s Customer

Technical Support within the limited warranty period. Refer below to find the appropriate contact

information for obtaining customer assistance. If limited warranty service is required, Aventura

Technologies, Inc. will issue a Return Material Authorization Number. You must ship the products back

to Aventura Technologies, Inc. in their original or equivalent packaging, prepay shipping charges, and

insure the shipment or accept the risk of loss or damage during shipment. Aventura Technologies, Inc.

will ship the repaired or replacement products to you freight prepaid if you use an address in the

continental United States, where applicable. Shipments to other locations will be made freight collect.

To view the full terms of the warranty, please go to: www.ati247.com

SERVICE INFORMATION

There are no user serviceable parts inside the unit.

In the event that service is required to this unit, please direct all inquiries to:

Aventura Technologies, Inc.

180 Adams Avenue Phone: (631) 300-4000

Hauppauge, NY 11788 FAX (631) 434-7000

E-mail:

[email protected]

Aventura FBR-1VS-RX User manual

Brand: Aventura

Model: FBR-1VS-RX

Category: Network media converters

Type: User manual

This manual is also suitable for

Download PDF

report

Aventura FBR-1VS-RX User manual

This manual is also suitable for

Aventura FBR-1VS-RX User manual

Related papers

Other documents