Aventura FBR-1GE2LX-SFP User manual

Category
Network media converters
Type
User manual
AventuraTechnologies
180AdamsAvenue
Hauppauge,NY11788
(877)7079600
www.aventuratechnologies.com
Instruction Manual
SFP Based, 10/100/1000 Ethernet, 3-Port Unmanaged Switch /
Media Converter
Model Numbers:
FBR-1GE2LX-SFP – SFP Based, 10/100/1000 Mbps Ethernet, 3-Port Unmanaged Switch
/ Media Converter
© Copyright 2008, Aventura Technologies, Inc.
© Copyright 2008, Aventura Technologies, Inc.
2
INSTALLATION AND OPERATION INSTRUCTIONS
FUNCTIONAL DESCRIPTION
The FBR-1GE2LX-SFP is a three-port unmanaged switch, with one UTP 10/100/1000 Ethernet
interface and two SFP based optical interfaces. The FBR-1GE2LX-SFP is ideal for optical daisy-chain
applications as an add-drop multiplexer, where multiple devices, such as IP cameras, share a single fiber
link. The unit uses industry standard Small Form-Factor, Pluggable (SFP) modules for connecting to the
fiber media. Proper Aventura Technologies approved SFP modules are selected by the customer to
accommodate the type and number of fibers, as well as the transmission distance for each link.
The FBR-1GE2LX-SFP converts a single 10/100/1000base-T/TX Ethernet input to an optical fiber
output and transmits it over one of the two fiber links, based on the address of the destination device.
The FBR-1GE2LX-SFP converts any packet received from either optical link and addressed to the IP
address of a device connected to the unit’s UTP port, to a single 10/100/1000base-T/TX Ethernet output.
The FBR-1GE2LX-SFP also passes through any packet received from either fiber link to the other fiber
link, based on the destination address.
The FBR-1GE2LX-SFP is configured to auto-negotiate the data rate on the UTP Ethernet port to either
10, 100, or 1000 Mbps and operating mode to either full or half-duplex. Additionally, the unit is
configured to perform the MDI/MDIX sensing and switching automatically. This feature allows for the
use of standard, straight through patch cords, without regard to the configuration (MDI or MDIX) of the
device the FBR-1GE2LX-SFP unit is connected to.
The data rate on the optical port of the FBR-1GE2LX-SFP is always 1000Mbps, full-duplex.
The FBR-1GE2LX-SFP can operate with two different SFP modules at the same time. This feature
allows the unit to interconnect two different fiber infrastructure types (e.g. convert a single fiber,
multimode, connection to a two-fiber, single mode connection.)
This unit is contained in a compact and rugged steel housing with internal dc voltage regulation. The
detachable terminal block and LED indicators provide for easy installation and monitoring of Ethernet,
optical link, and dc power status.
The unit operates as either a surface mounted, modular, stand-alone device, or within a rack mounted
card cage.
INSTALLATION
THE INSTALLATION OF THIS UNIT SHOULD BE MADE BY A QUALIFIED SERVICE
PERSON(S) AND MUST CONFORM TO ALL LOCAL CODES.
The physical outline and front/rear panel configuration of the unit is detailed in Figure 2.
Mount the unit to a secure surface using #8 (3mm) hardware in two places. See Figure 3 for a full size
mounting template. Be sure to allow sufficient room for the required minimum bend radius of the fiber
cable used.
© Copyright 2008, Aventura Technologies, Inc.
3
POWER SOURCE
The unit requires a +12VDC power source for proper operation. The DC input is diode protected against
reverse polarity connection.
In the USA and in Canada, for standalone surface mounted installation, an Aventura Technologies FBR-
PSUS12DC1A is supplied with this unit. Contact Aventura Technologies for ordering power supply
units for use in countries other than the USA and Canada.
When installed in a rack mounted card cage, the power for the unit is supplied from the card cage’s
power supply.
POWER CONNECTION
Power is supplied to the unit via a two-pin terminal block connector. Follow the labeling on the unit for
proper connections of the +12 volt dc and ground leads.
ETHERNET CONNECTION
The UTP Ethernet connection is made via an RJ-45 connector on the front of the unit. For proper
operation, the use of a patch cord and/or cable rated Category-5e or better is required.
FIBER CONNECTION
There are two SFP module slots on the front of the unit. The fiber optic connections vary, depending on
the selection of SFP module. Refer to the instructions supplied with the SFP modules for the proper
procedure of installing the SFP modules in the FBR-1GE2LX-SFP unit, as well as for the proper
procedure for connecting the fibers to the SFP modules.
STATUS INDICATORS
Each unit provides the following LED status indicators to aid in installation and troubleshooting:
POWER INDICATOR
A bi-color LED indicator monitors the voltage at the unit’s input connector and the operating internal
voltage of the module. The power status associated with this indicator is summarized below.
Power Indicator Power Status
Green Proper Input Voltage Present – Proper Internal Operating Voltage Present
Red Proper Input Voltage Present – Internal Operating Voltage Faulty
Off No Input Voltage Detected
OPTICAL LINK INDICATOR
A bi-color LED indicator for each SFP interface monitors the power of, and proper synchronization with
the optical input signal that is being received at the FBR-1FE1FX-SFP. The optical link status
associated with these indicators is summarized below.
Optical Link Indicator Optical Status
Green Proper Optical Input Present
Red Optical Input Not Detected
Off Check Power Supply
ETHERNET INDICATORS
Two LED indicators on the RJ-45 connector of the FBR-1GE2LX-SFP unit monitor the status and
operating mode of the UTP Ethernet link. The Ethernet status associated with these indicators is
summarized below.
Ethernet Indicators Ethernet Status
Speed
(Bi-Color)
Lit Amber: Link operating at 1000Mbps
Lit Green: Link operating at 100Mbps
Unlit: link operating at 10Mbps or no link
Link/Activity
(GREEN)
Lit: Good link on the port
Blinking: The port is receiving/transmitting data
Unlit: No link
Device Compatible With
FBR-1GE2LX-SFP FBR-1GE1LX-SFP-MINI
FBR-1GE1LX-SFP
FBR-2X1GE1LX-SFP
FBR-1GE2LX-SFP
FBR-8FE1LX-SFP
Figure 1 – List of Compatible Devices
Figure 2 – Physical Outline And Front/Rear Panel Configuration Of Units
© Copyright 2008, Aventura Technologies, Inc.
4
Figure 3 – Surface Mounting Template (1:1)
© Copyright 2008, Aventura Technologies, Inc.
5
LIMITED LIFETIME WARRANTY INFORMATION
This limited lifetime warranty applies only to the original end user customer of the product for so long
as the original end user customer owns the product. This limited warranty is non-transferable.
Damage due to shipping the products to you is covered under this limited warranty. Otherwise, this
limited warranty does not cover damage due to external causes, including accident, abuse, misuse,
problems with electrical power, servicing not authorized by Aventura Technologies, Inc., usage not in
accordance with product instructions, failure to perform required preventive maintenance, and problems
caused by use of parts and components not supplied by Aventura Technologies, Inc.
During the warranty period beginning on the invoice date, Aventura Technologies, Inc. will repair or
replace products covered under this limited warranty that are returned to Aventura Technologies, Inc.'s
facility. To request limited warranty service, you must contact Aventura Technologies, Inc.'s Customer
Technical Support within the limited warranty period. Refer below to find the appropriate contact
information for obtaining customer assistance. If limited warranty service is required, Aventura
Technologies, Inc. will issue a Return Material Authorization Number. You must ship the products back
to Aventura Technologies, Inc. in their original or equivalent packaging, prepay shipping charges, and
insure the shipment or accept the risk of loss or damage during shipment. Aventura Technologies, Inc.
will ship the repaired or replacement products to you freight prepaid if you use an address in the
continental United States, where applicable. Shipments to other locations will be made freight collect.
To view the full terms of the warranty, please go to: www.ati247.com
SERVICE INFORMATION
There are no user serviceable parts inside the unit.
In the event that service is required to this unit, please direct all inquiries to:
Aventura Technologies, Inc.
180 Adams Avenue Phone: (631) 300-4000
Hauppauge, NY 11788 FAX (631) 434-7000
E-mail:
© Copyright 2008, Aventura Technologies, Inc.
6
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Aventura FBR-1GE2LX-SFP User manual

Category
Network media converters
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI