Belden BAT450-F User manual

Installation BAT450-F

Release

12

07/2020

Technical support

https://hirschmann-support.belden.com

User Manual

Installation

Industrial Access Point / Client / Access Bridge

BAT450-F

20.07.2020

Installation BAT450-F

Release

12

07/2020

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Contents

Safety instructions 7

About this manual 20

1 Description 21

1.1 General device description 21

1.2 Device name and product code 22

1.3 Device view 11n device variants (non-LTE) 24

1.4 Device view 11ac device variants (non-LTE) 26

1.5 Device view LTE device variants 27

1.6 Power supply 28

1.6.1 Supply voltage with the characteristic value W

(24 V DC) 28

1.6.2 Supply voltage with the characteristic value N

(110 V DC) 29

1.7 Ethernet ports 29

1.7.1 10/100/1000 Mbit/s PoE port 29

1.7.2 10/100/1000 Mbit/s twisted pair port 29

1.7.3 Pin assignments 30

1.8 Display elements 11n device variants (non-LTE) 30

1.8.1 Device state 30

1.8.2 LS/DA 31

1.9 Display elements 11ac device variants (non-LTE) 31

1.9.1 Device state 31

1.9.2 LS/DA 32

1.10 Display elements LTE device variants 32

1.10.1 Device state 32

1.10.2 LS/DA 33

1.11 Management interfaces 33

1.11.1 V.24 interface (external management) 33

1.11.2 Reset button 35

1.12 SIM card reader (exclusively for LTE device variants) 36

2 Installation 37

4

Installation BAT450-F

Release

12

07/2020

2.1 Checking the package contents 37

2.2 Installing and grounding the device 38

2.2.1 Installing the device onto or on a flat surface 38

2.2.2 Installing the device on a pole 39

2.2.3 Grounding the device 40

2.3 Installing the antennas 41

2.4 Connecting the power supply 41

2.4.1 Supply voltage with the characteristic value W

(24 V DC) 42

2.4.2 Supply voltage with the characteristic value N

(110 V DC) 42

2.5 Operating the device 43

2.5.1 Connecting the power supply 43

2.6 Connecting data cables 43

3 Defining IP parameters 44

4 First login (Password change) 45

5 Defining WLAN basic settings 46

6 Defining WWAN basic settings (exclusively for

LTE device variants) 47

7 Obtaining compliance for operation in the

European Union 48

8 Configuring the transmit power 51

9 Configuring the transmit power for the 4.9 GHz

band 53

10 Monitoring the ambient air temperature 55

11 Maintenance and service 56

12 Disassembly 57

13 Technical data 58

Installation BAT450-F

Release

12

07/2020

5

13.1 General technical data 58

13.2 Dimension drawings 60

13.3 11n WLAN module specifications 61

13.3.1 Radio technology 61

13.3.2 Roaming 61

13.3.3 Receiving sensitivity, transmit power, and data rate of

the WLAN module version EWLAN1 (Approvals 2,

characteristic value M or 9) 62

13.3.4 Receiving sensitivity, transmit power, and data rate of

the WLAN module version EWLAN1 for device

variants with approval for the 4.9 GHz band

(Approvals 2, characteristic value P) 66

13.3.5 Receiving sensitivity, transmit power, and data rate of

the WLAN module version EWLAN2 for high-gain

antennas (Approvals 2, characteristic value H) 68

13.4 11ac WLAN module specifications (exclusively for 11ac

device variants) 72

13.4.1 Radio technology 72

13.4.2 Roaming 72

13.4.3 Receiving sensitivity, transmit power and data rate 73

13.5 LTE specifications (exclusively for LTE device variants) 78

13.5.1 LTE module 78

13.5.2 GNSS (Global Navigation Satellite System) 79

13.5.3 Conducted RX sensitivity (LTE Bands) 79

13.5.4 Conducted RX sensitivity (UMTS Bands) 80

13.5.5 Conducted RX sensitivity (GSM/EDGE Bands) 80

13.5.6 Conducted TX power tolerances 80

13.6 EMC 81

13.7 Immunity 81

13.8 Network range 82

13.9 Power consumption/power output 82

14 Scope of delivery 11n device variants (non-LTE) 83

15 Scope of delivery 11ac device variants (non-LTE) 85

16 Scope of delivery LTE device variants 87

17 Accessories 11n device variants (non-LTE) 89

6

Installation BAT450-F

Release

12

07/2020

18 Accessories 11ac device variants (non-LTE) 90

19 Accessories LTE device variants 91

20 Underlying technical standards 92

A Further support 94

Installation BAT450-F

Release

12

07/2020

7

Safety instructions

 General safety instructions

You operate this device with electricity. Improper usage of the device

entails the risk of physical injury or significant property damage. The

proper and safe operation of this device depends on proper handling

during transportation, proper storage and installation, and careful

operation and maintenance procedures.

 Before connecting any cable, read this document, and the safety

instructions and warnings.

 Operate the device with undamaged components exclusively.

 The device is free of any service components. In case of a damaged

or malfunctioning device, turn off the supply voltage and return the

device to Hirschmann for inspection.

 Certified usage

 Use the product only for the application cases described in the

Hirschmann product information, including this manual.

 Operate the product only according to the technical specifications.

See “Technical data” on page 58.

 Connect to the product only components suitable for the requirements

of the specific application case.

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all

the data transmission devices individually.

Before you start any machine which is controlled via data transmission, be

sure to complete the configuration of all data transmission devices.

Failure to follow this instruction can result in death, serious injury, or

equipment damage.

8

Installation BAT450-F

Release

12

07/2020

 Installation site requirements

 During the installation, make sure that you adhere to the regulations of

the country in which you are operating the device.

 In ambient temperatures under +14 °F (-10 °C), use cabling designed

for minimum temperatures.

 Applies to device variants featuring supply voltage with characteristic

value N (110 V DC):

See “Device name and product code” on page 22.

Exclusively install this device in a restricted access location, to which

maintenance staff have exclusive access. Install the device in such a

way that it is protected against mechanical forces in the area of the

power supply.

 Device casing

Only technicians authorized by the manufacturer are permitted to open

the casing.

 Never insert pointed objects (narrow screwdrivers, wires, etc.) into the

device or into the connection terminals for electric conductors. Do not

touch the connection terminals.

 Install the device in the vertical position, with the antenna connections

pointing upwards.

 At ambient air temperatures > +140 °F (+60 °C):

The surfaces of the device housing may become hot. Avoid touching

the device while it is operating.

 Qualification requirements for personnel

 Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

 Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the

prerequisite for grounding and labeling circuits, devices, and systems

in accordance with current standards in safety technology.

 Qualified personnel are aware of the dangers that exist in their work.

 Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

 Qualified personnel receive training on a regular basis.

 National and international safety regulations

 Verify that the electrical installation meets local or nationally applicable

safety regulations.

 Grounding the device

Grounding the device is by means of a separate ground connection on the

device.

 Ground the device before connecting any other cables.

 Disconnect the grounding only after disconnecting all other cables.

Installation BAT450-F

Release

12

07/2020

9

The overall shield of a connected shielded twisted pair cable is connected

to the ground connection on the metal housing as a conductor.

 Requirements for connecting electrical wires

Before connecting the electrical wires, always verify that the

requirements listed are complied with.

 Requirements for connecting the supply voltage

The following requirements apply without restrictions:

 The electrical wires are voltage-free.

 The cables used are permitted for the temperature range of the application case.

 Relevant for North America:

The power supply cables are suitable for ambient air temperatures of at least +167 °F

(+75 °C). The power supply cable wires are made of copper.

Table 1: Requirements for connecting electrical wires

Prerequisites:

All variants All of the following requirements are complied with:

 The supply voltage corresponds to the voltage specified on the type

plate of the device.

 The power supply conforms to overvoltage category I or II.

 The power supply has an easily accessible disconnecting device (for

example a switch or a plug). This disconnecting device is clearly

identified. So in the case of an emergency, it is clear which

disconnecting device belongs to which power supply cable.

 The cross-section of the ground conductor is the same size as or

bigger than the cross-section of the power supply cables.

 The power supply cable is suitable for the voltage, the current and the

physical load. Hirschmann recommends a wire diameter of

0.25 mm² (AWG24) to 0.75 mm² (AWG19).

Only for device

variants featuring

supply voltage with

characteristic

value W (24 V DC):

The following requirements apply alternatively:

Alternative 1 The power supply complies with the requirements

for a limited power source (LPS) as per EN 60950-1.

Alternative 2 Relevant for North America:

The power supply complies with the requirements

according to NEC Class 2.

Alternative 3 All of the following requirements are complied with:

 The power supply complies with the

requirements for a safety extra-low voltage

(SELV) as per IEC/EN 60950-1.

 A suitable fuse is located in the plus conductor

of the power supply.

Regarding the properties of this fuse:

See “General technical data” on page 58.

Only for device

variants featuring

supply voltage with

characteristic

value N (110 V DC):

A fuse suitable for DC voltage is located in the plus conductor of the power

supply.

Regarding the properties of this fuse:

See “General technical data” on page 58.

Table 2: Requirements for connecting the supply voltage

10

Installation BAT450-F

Release

12

07/2020

 Lightning protection

 The installation of the device occurs in accordance with valid

standards (such as IEC 62305 / DIN EN 62305 (VDE 0185-305)), and

in accordance with the lightning protection procedures recognized and

proven for the application and the environment.

 Refer to the information in the “WLAN Outdoor Guide” on “Lightning

and overvoltage protection”.

The manual is available for download on the Internet: https://

www.doc.hirschmann.com

 Protect antennas installed outside with lightning protection devices (for

example lightning conductors).

 Take lightning protection measures which mitigate the effects of

lightning strikes.

 E marking

The labeled devices comply with the regulations contained in the following

European directive(s):

Regulation No. 10 of the Economic Commission for Europe of the United

Nations (UN/ECE): Devices with an approval are labeled with the

E type approval mark.

Devices are not specified for operation during the motor start phase.

 CE marking

The labeled devices comply with the regulations contained in the following

European directive(s):

2011/65/EU and 2015/863/EU (RoHS)

Directive of the European Parliament and of the Council on the restriction

of the use of certain hazardous substances in electrical and electronic

equipment.

2014/53/EU (RED)

Directive of the European Parliament and of the council on the

harmonization of the laws of the Member States relating to the making

available on the market of radio equipment.

This product may be operated in all EU (European Union)

countries under the condition that it has been configured correctly.

Installation BAT450-F

Release

12

07/2020

11

In accordance with the above-named EU directive(s), the EU conformity

declaration will be available to the relevant authorities at the following

address:

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

www.hirschmann.com

The product can be used in residential areas (residential, commercial and

light-industrial environments) and in industrial areas.

12

Installation BAT450-F

Release

12

07/2020

Notes for countries with the following country codes:

 The RED compliance requires compliant operation of the device in the

5 GHz band channels. Compliant operation of the device is achieved

by an unchangeable determination of the country setting. To obtain

RED compliance, perform the work steps described in chapter

“Obtaining compliance for operation in the European Union” on

page 48.

 Applies to the operation of devices in the 5.6 to 5.65 GHz band:

Install an antenna with an antenna gain of at least 3 dBi.

AT

BE

BG

CH

CY

CZ

DE

DK

EE

EL

ES

FI

FR

HR

HU

IE

IT

LI

LT

LU

LV

MT

NL

NO

PL

PT

RO

RS

SE

SI

SK

TR

UK

Installation BAT450-F

Release

12

07/2020

13

Notes for Germany (DE), Ireland (IE), and the United Kingdom (UK):

Operation in the 5.8 GHz band at a radiated power (EIRP) >25 mW is

subject to meeting the following conditions:

 Germany (DE)

Frequency range: 5725 MHz to 5875 MHz

Condition: The usage of this band is restricted to commercial public

telecommunication services. Registration at the Federal Network

Agency is required.

Name and website of the competent authority:

Bundesnetzagentur

www.bundesnetzagentur.de

 Ireland (IE)

Frequency range: 5725 MHz to 5875 MHz

Condition: Registration of operational base stations

Name and website of the competent authority:

Commission for Communications Regulation

www.comreg.ie

 United Kingdom (UK):

Frequency range: 5725 MHz to 5850 MHz

Condition: Light-licensing regime

Name and website of the competent authority:

Ofcom

www.ofcom.org.uk

DE

IE

UK

14

Installation BAT450-F

Release

12

07/2020

 LED or laser components

LED or LASER components according to IEC 60825-1 (2014):

CLASS 1 LASER PRODUCT

CLASS 1 LED PRODUCT

 FCC note for 11n device variants

Supplier's Declaration of Conformity

47 CFR § 2.1077 Compliance Information

BAT450-F

U.S. Contact Information

Belden – St. Louis

1 N. Brentwood Blvd. 15th Floor

St. Louis, Missouri 63105, United States

Phone: 314.854.8000

This device complies with part 15 of the FCC rules.

Operation is subject to the following two conditions:

 This device may not cause harmful interference, and

 This device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

 Reposition the receiver antenna or change the angle of the receiver

antenna.

 Increase the separation between the device and the receiver.

 Connect the device to a different outlet on a different power supply

cable from that to which the receiver is connected.

 Consult a specialist retailer or an electronic systems engineer for help.

Changes or modifications not expressly approved by the holder of the

certificate could void the user’s authority to operate this equipment.

Installation BAT450-F

Release

12

07/2020

15

EWLAN1 Module

Note for the use in the USA and in Canada

The following section applies to device variants with characteristic

value US (USA/Canada) for country approvals, which are labeled as

follows:

Contains Transmitter Module

FCC ID: U99EWLAN1

IC: 4019A-EWLAN1

This equipment complies with FCC and IC RSS-102 radiation exposure

limits set forth for an uncontrolled environment. Install and operate this

equipment with a minimum distance of 19.7 in (50 cm) (related to a 9 dBi

antenna) between the radiation source and your body.

The antenna used for this transmitter must not be co-located with any

other transmitters within a host device, except in accordance with FCC

multi-transmitter product procedures.

This transmitter is restricted to indoor use only within the

5.15 to 5.25 GHz band to reduce potential for harmful interference to co-

channel mobile satellite systems.

The power of the device was reduced by 6 dB on channel 149

(5745 MHz) for all modulations to be compliant to the band edge limits.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003

du Canada.

To reduce potential radio interference to other users, the antenna type

and its gain should be so chosen that the equivalent isotropically radiated

power (EIRP) is not more than that permitted for successful

communication.

This device has been designed to operate with the antennas listed below

in point-to-multipoint systems, and having a maximum gain of 9 dBi:

The FCC approval is valid only in conjunction with the listed antennas. If

other antennas are used, the approval expires. The responsibility lies with

the operator of the system. The required antenna impedance is 50 .

Antenna(s) for operation with this

device:

Permitted band of operation

2.4 GHz band 5.18 GHz ...

5.24 GHz band

5.745 GHz ...

5.825 GHz band

BAT-ANT-N-3AGN-IP67 Yes Yes Yes

BAT-ANT-N-MiMoDB-5N-IP65 Yes Yes Yes

BAT-ANT-N-MiMo5-9N-IP65 No Yes Yes

BAT-ANT-N-8G-DS-IP65 Yes No No

16

Installation BAT450-F

Release

12

07/2020

Applies exclusively to device variants with approval for the 4.9 GHz band

(Approvals 2, characteristic value P) according to

FCC 47CFR Part 90 Subpart Y:

 Operation of the device in the 4.9 GHz band requires trained

personnel familiar with the regulatory requirements for operation

according to FCC 47CFR Part 90 Subpart Y.

 The 4.9 GHz band is a licensed band. State and local government

entities that provide public safety services are eligible to apply for

4.9 GHz licenses. For more information, see the Federal

Communications Commission (FCC) regulations. The installer or

operator is responsible for obtaining the appropriate site licenses

before installing or using the system.

 The antenna gain of the antenna must not exceed 9 dBi.

 For antennas with an antenna gain >9 dBi, the transmit power must be

reduced accordingly in the device software. You can find step-by-step

instructions for reducing the transmit power in the device software in

the “Configuring the transmit power for the 4.9 GHz band” on page 53

chapter.

EWLAN2 Module

Note for the use in the USA and in Canada

The following section applies to device variants with characteristic

value US (USA/Canada) for country approvals, which are labeled as

follows:

Contains Transmitter Module

FCC ID: U99EWLAN2

IC: 4019A-EWLAN2

This equipment complies with FCC and IC RSS-102 radiation exposure

limits set forth for an uncontrolled environment. This equipment should be

installed and operated with minimum distance of 19.7 in (50 cm) (related

to a 18 dBi antenna) between the radiation source and your body.

The antenna used for this transmitter must not be co-located with any

other transmitters within a host device, except in accordance with FCC

multi-transmitter product procedures.

This transmitter is restricted to indoor use only within the

5.15 to 5.25 GHz band to reduce potential for harmful interference to co-

channel mobile satellite systems.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003

du Canada.

Installation BAT450-F

Release

12

07/2020

17

To reduce potential radio interference to other users, the antenna type

and its gain should be so chosen that the equivalent isotropically radiated

power (EIRP) is not more than that permitted for successful

communication.

This device has been designed to operate with the antennas listed below

having a maximum gain of 18 dBi:

The FCC approval is valid only in conjunction with the listed antennas. If

other antennas are used, the approval expires. The responsibility lies with

the operator of the system. The required antenna impedance is 50 .

 FCC note for 11ac device variants

Supplier's Declaration of Conformity

47 CFR § 2.1077 Compliance Information

BAT450-F

U.S. Contact Information

Belden – St. Louis

1 N. Brentwood Blvd. 15th Floor

St. Louis, Missouri 63105, United States

Phone: 314.854.8000

This device complies with part 15 of the FCC rules.

Operation is subject to the following two conditions:

 This device may not cause harmful interference, and

 This device must accept any interference received, including

interference that may cause undesired operation.

Antenna(s) for operation with this

device:

Permitted band of operation

2.4 GHz band 5.18 GHz ...

5.24 GHz band

5.745 GHz ...

5.825 GHz band

BAT-ANT-N-3AGN-IP67 Yes Yes Yes

BAT-ANT-N-MiMoDB-5N-IP65 Yes Yes Yes

BAT-ANT-N-MiMo5-9N-IP65 No Yes Yes

BAT-ANT-N-8G-DS-IP65 Yes No No

BAT-ANT-N-MiMo-18N-IP65

a

a. Note: Connect the BAT-ANT-N-MiMo-18N-IP65 to the WLAN module as follows:

 Connect the antenna port "Ver" with the WLAN-antenna-port 1.

 Connect the antenna port "+45 °" with the WLAN antenna port 2.

 Connect the antenna port "-45 °" with the WLAN antenna port 3.

 Connect the BAT-ANT-N-MiMo-18N-IP65 antenna in this way exclusively.

Differing connection configurations are illegal.

No No Yes

18