Hirschmann BAT-R User manual

Brand: Hirschmann

Model: BAT-R

Type: User manual

Installation BAT-R

Release

07/2020

Technical support

https://hirschmann-support.belden.com

User Manual

Installation

Open Dual-Band Industrial Access-Point / Client / Access-

Bridge

OpenBAT-Family: BAT-R

10.07.2020

Installation BAT-R

Release

07/2020

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Installation BAT-R

Release

07/2020

Contents

Safety instructions 7

About this manual 26

Key 27

1 Description 28

1.1 General description 28

1.2 Device name and product code 29

1.3 Device view 33

1.4 Power supply 34

1.4.1 Supply voltage with the characteristic value C

(24 V DC ... 48 V DC) 35

1.4.2 Supply voltage with the characteristic value K

(60 V DC ... 250 V DC / 110 V AC ... 230 V AC,

50 Hz ... 60 Hz) 35

1.4.3 Supply voltage with the characteristic value P (Power

supply only through PoE) 35

1.4.4 Supply voltage with the characteristic value W

(24 V DC) 35

1.5 Ethernet ports 36

1.5.1 Gigabit combo port 36

1.5.2 10/100/1000 Mbit/s twisted-pair connection (optional) 37

1.5.3 Pin assignments 38

1.6 Connections for antennas 39

1.7 Display elements 39

1.7.1 Meaning of the LEDs 39

1.7.2 Device state 39

1.7.3 Port status 40

1.8 Management interfaces 41

1.8.1 V.24 interface (external management) 41

1.8.2 USB interface 42

1.9 Signal contact 43

1.10 Reset button 43

Installation BAT-R

Release

07/2020

2 Installation 44

2.1 Checking the package contents 44

2.2 Installing and grounding the device 44

2.2.1 Installing the device onto the DIN rail 45

2.2.2 Mounting on a vertical flat surface 45

2.2.3 Grounding the device 45

2.3 Installing an SFP transceiver (optional) 46

2.4 Installing the antennas 46

2.5 Connecting the terminal blocks (optional) 47

2.5.1 Supply voltage with the characteristic value C

(24 V DC ... 48 V DC) 48

2.5.2 Supply voltage with the characteristic value K

(60 V DC ... 250 V DC / 110 V AC ... 230 V AC,

50 Hz ... 60 Hz) 48

2.5.3 Supply voltage with the characteristic value W

(24 V DC) 49

2.5.4 Signal contact 50

2.6 Operating the device 51

2.6.1 Connecting the power supply through a terminal

block 51

2.6.2 Connecting the power supply through PoE 51

2.7 Connecting data cables 52

2.7.1 Gigabit combo port 52

2.7.2 10/100/1000 Mbit/s twisted-pair connection (optional) 52

3 Making basic settings 53

4 First login (Password change) 54

5 Obtain compliance for operation in the European

Union 55

6 Configuring the transmit power 58

7 Configuring the transmit power for the 4.9 GHz

band 60

8 Maintenance and service 62

Installation BAT-R

Release

07/2020

9 Disassembly 63

9.1 Removing the device 63

9.2 Removing an SFP transceiver (optional) 63

10 Technical data 64

10.1 General technical data 64

10.2 Dimension drawings 66

10.3 Radio technology 68

10.4 Roaming 68

10.5 Receiving sensitivity, transmit power, and data rate of the

WLAN module version EWLAN1 (Approvals 2, characteristic

value M, V or 9) 69

10.5.1 IEEE 802.11b 69

10.5.2 IEEE 802.11g 69

10.5.3 IEEE 802.11a 70

10.5.4 IEEE 802.11n 70

10.6 Receiving sensitivity, transmit power, and data rate of the

WLAN module version EWLAN1 for device variants with

approval for the 4.9 GHz band (Approvals 2, characteristic

value P) 73

10.6.1 IEEE 802.11a, Bandwidth 5 MHz 73

10.6.2 IEEE 802.11a, Bandwidth 10 MHz 73

10.6.3 IEEE 802.11a, Bandwidth 20 MHz 74

10.7 Receiving sensitivity, transmit power, and data rate of the

WLAN module version EWLAN2 for high-gain antennas

(Approvals 2, characteristic value H) 75

10.7.1 IEEE 802.11b 75

10.7.2 IEEE 802.11g 75

10.7.3 IEEE 802.11a 76

10.7.4 IEEE 802.11n 76

10.8 EMC and immunity 78

10.9 Network range 79

10.10 Power consumption/power output 80

11 Scope of delivery, order numbers and

accessories 81

Installation BAT-R

Release

07/2020

12 Underlying technical standards 83

A Further support 85

Installation BAT-R

Release

07/2020

Safety instructions

 General safety instructions

You operate this device with electricity. Improper usage of the device

entails the risk of physical injury or significant property damage. The

proper and safe operation of this device depends on proper handling

during transportation, proper storage and installation, and careful

operation and maintenance procedures.

 Before connecting any cable, read this document, and the safety

instructions and warnings.

 Operate the device with undamaged components exclusively.

 The device is free of any service components. In case of a damaged

or malfunctioning device, turn off the supply voltage and return the

device to Hirschmann for inspection.

 Internal fuses are triggered only in the case of a detected error in the

device. In case of damage or malfunction of the device, turn off the

supply voltage and return the device to the plant for inspection.

 Certified usage

 Use the product only for the application cases described in the

Hirschmann product information, including this manual.

 Operate the product only according to the technical specifications.

See “Technical data” on page 64.

 Connect to the product only components suitable for the requirements

of the specific application case.

 Installation site requirements

Restricted access location:

 The location is outside the operator access area.

 The location is accessible to the service personnel even when the

device is switched on.

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all

the data transmission devices individually.

Before you start any machine which is controlled via data transmission, be

sure to complete the configuration of all data transmission devices.

Failure to follow this instruction can result in death, serious injury, or

equipment damage.

Installation BAT-R

Release

07/2020

Indoor operator access area:

 The location is accessible without tools.

 The person responsible for the area has provided access for the

operator intentionally.

 The operator knows of the access possibilities, regardless of whether

they need a tool.

 Applies to device variants featuring supply voltage with characteristic

value K: (60 V DC ... 250 V DC / 110 V AC ... 230 V AC, 50 Hz ...

60 Hz):

See “Device name and product code” on page 29.

Install this device only in a switch cabinet or in an operating site with

restricted access, to which maintenance staff have exclusive access.

 Relevant for Europe:

Install the device in a fire enclosure according to EN 60950-1.

In the following exceptional cases, you do not require a fire-protected

shell:

 You are supplying voltage to the device only via PoE.

 You are supplying only 24 V to the device and are using a fuse.

Regarding the properties of this fuse: See “General technical data”

on page 64.

 For use in UL 60950-1 conditions:

Install the device in a fire enclosure.

 Device casing

Only technicians authorized by the manufacturer are permitted to open

the casing.

 Never insert pointed objects (narrow screwdrivers, wires, etc.) into the

device or into the connection terminals for electric conductors. Do not

touch the connection terminals.

 Keep the ventilation slits free to ensure good air circulation.

 Mount the device in the vertical position.

 At ambient air temperatures > 140 °F (+60 °C):

The surfaces of the device housing may become hot. Avoid touching

the device while it is operating.

 Qualification requirements for personnel

 Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

 Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the

prerequisite for grounding and labeling circuits, devices, and systems

in accordance with current standards in safety technology.

 Qualified personnel are aware of the dangers that exist in their work.

Installation BAT-R

Release

07/2020

 Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

 Qualified personnel receive training on a regular basis.

 National and international safety regulations

 Verify that the electrical installation meets local or nationally applicable

safety regulations.

 When installing antennas, observe the regulations of the country in

which you are operating the WLAN device with regard to the general

operating permission and the maximum emission levels.

 Install and operate this equipment with a minimum distance of

19.7 inches (50 cm) between the antenna and your body.

 Grounding the device

Grounding the device is by means of a separate ground connection on the

device.

 Ground the device before connecting any other cables.

 Disconnect the grounding only after disconnecting all other cables.

The overall shield of a connected shielded twisted pair cable is connected

to the grounding connector on the front panel as a conductor.

 Lightning protection

 Refer to the information in the “WLAN Outdoor Guide” on “Lightning

and overvoltage protection”.

The manual is available for download on the Internet: https://

www.doc.hirschmann.com

 Install over voltage protector devices on every outdoor Ethernet cable.

 Protect antennas installed outside with lightning protection devices (for

example lightning conductors).

 Take lightning protection measures which mitigate the effects of

lightning strikes.

 The installation of the device occurs in accordance with valid

standards (such as IEC 62305 / DIN EN 62305 (VDE 0185-305)), and

in accordance with the lightning protection procedures recognized and

proven for the application and the environment.

 Requirements for connecting electrical wires

Before connecting the electrical wires, always verify that the

requirements listed are complied with.

Installation BAT-R

Release

07/2020

The following requirements apply without restrictions:

 The electrical wires are voltage-free.

 The cables used are permitted for the temperature range of the application case.

 Relevant for North America:

The power supply cables are suitable for ambient air temperatures of at least 167 °F

(75 °C). The power supply cable wires are made of copper.

Table 1: Requirements for connecting electrical wires

Installation BAT-R

Release

07/2020

 Requirements for connecting the supply voltage

 Enable the supply voltage for the device only when the following

requirements are fulfilled:

The following requirements apply without restrictions:

All variants All of the following requirements are complied with:

 The supply voltage corresponds to the voltage specified on the type

plate of the device.

 The power supply conforms to overvoltage category I or II.

 The power supply has an easily accessible disconnecting device (for

example a switch or a plug). This disconnecting device is clearly

identified. So in the case of an emergency, it is clear which

disconnecting device belongs to which power supply cable.

 The cross-section of the ground conductor is the same size as or

bigger than the cross-section of the power supply cables.

Only for device

variants featuring

supply voltage with

characteristic

value C (24 V DC ...

48 V DC) or W

(24 V DC):

The wire diameter of the power supply cable is at least 1 mm² (North

America: AWG16) on the supply voltage input.

The following requirements are alternatively complied with:

Alternative 1 The power supply complies with the requirements

for a limited power source (LPS) as per EN 60950-1.

Alternative 2 Relevant for North America:

The power supply complies with the requirements

according to NEC Class 2.

Alternative 3 All of the following requirements are complied with:

 The power supply complies with the

requirements for a safety extra-low voltage

(SELV) as per IEC/EN 60950-1.

 A fuse suitable for DC voltage is located in the

plus conductor of the power supply.

The minus conductor is on ground potential.

Otherwise, a fuse is also located in the minus

conductor.

Regarding the properties of this fuse:

See “General technical data” on page 64.

Only for device

variants featuring

supply voltage with

characteristic

value K (60 V DC ...

250 V DC /

110 V AC ...

230 V AC, 50 Hz ...

60 Hz):

All of the following requirements are complied with:

 Supply with DC voltage:

A back-up fuse suitable for DC voltage is located in the plus conductor

of the power supply.

The minus conductor is on ground potential. Otherwise, a back-up

fuse is also located in the minus conductor.

Regarding the properties of this back-up fuse:

See “General technical data” on page 64.

The wire diameter of the power supply cable is at least 1 mm² (North

America: AWG16) on the supply voltage input.

 Supply with AC voltage:

A fuse is located in the outer conductor of the power supply.

The neutral conductor is on ground potential at both voltage inputs.

Otherwise, a fuse is also located in the neutral conductor.

Regarding the properties of this fuse:

See “General technical data” on page 64.

The wire diameter of the power supply cable is at least 0.75 mm²

(North America: AWG18) on the supply voltage input.

Table 2: Requirements for connecting the supply voltage

Installation BAT-R

Release

07/2020

 the housing is closed

 the terminal blocks are wired correctly

 the terminal blocks for the power supply are connected

 For supply voltage connections with protective conductor connection:

First connect the protective conductor before connecting the wires for

the supply voltage.

If your device comprises a 2nd supply voltage connection of this type:

First connect the protective conductor before connecting the wires for

the supply voltages.

Installation BAT-R

Release

07/2020

 ATEX directive 2014/34/EU – specific regulations for safe

operation

In Ex zone 2, only devices with a corresponding label may be operated.

When operating the BAT-R types with characteristic value G for

Approvals 1 (ATEX zone 2), the following applies:

 Never use the supply voltage with characteristic value K (60 V DC ...

250 V DC / 110 V AC ... 230 V AC, 50 Hz ... 60 Hz) in Ex zone 2.

II 3 G Ex nA IIC T4 Gc DEKRA 13ATEX0027 X

40 °F ... +158 °F (40 °C ... +70 °C) for temperature range

characteristic value T and E

+32 °F ... +140 °F (0 °C ... +60 °C) for temperature range

characteristic value S

DO NOT OPEN THE DEVICE WHEN IT IS ELECTRICALLY CHARGED.

THE USB CONNECTOR MUST NOT BE USED WHEN THE DEVICE IS

OPERATED IN EXPLOSIVE HAZARDOUS LOCATIONS.

Special conditions for safe use

 For supply voltage with characteristic value C (24 V DC ... 48 V DC)

and W (24 V DC):

Provisions shall be made to prevent the rated voltage from being

exceeded by transient disturbances of more than 119 V.

 When the temperature under rated conditions exceeds 158 °F (70 °C)

at the cable or conduit entry point, or 176 °F (80 °C) at the branching

point of the conductors, take care that the temperature specification of

the selected cable is in compliance with the actual measured

temperature values.

 Install the modules in a suitable enclosure in accordance with

EN 60079-15 providing a degree of protection of at least IP54

according to EN 60529, taking into account the environmental

conditions under which the equipment will be used.

Temperature code T4 Ambient temperature 40 °F ... +158 °F (40 °C ... +70 °C ;

temperature range with characteristic value T and E)

Ambient temperature +32 °F ... +140 °F (0 °C ... +60 °C;

temperature range with characteristic value S)

List of standards EN 60079-0:2012 + A11

EN 60079-15:2010

Installation BAT-R

Release

07/2020

 Relevant for use in explosion hazard areas (Hazardous

Locations, Class I, Division 2):

In Ex zone 2, only the devices with a corresponding label may be

operated in explosion hazard areas Class I, Division 2.

When operating the BAT-R types in explosion hazard areas Class I,

Division 2, the following applies:

DO NOT OPEN THE DEVICE WHEN IT IS ELECTRICALLY CHARGED.

 Use the device only with mounted impact protection.

Class I, Div. 2 Goups A, B, C and D

Temperature code T4 Ambient: 40 °F ... +158 °F (40 °C ... +70 °C; for

characteristic value T and E for temperature range)

Ambient: +32 °F ... +140 °F (0 °C ... +60 °C; for characteristic

value S for temperature range)

List of standards FM3600,

FM3611

CAN/CSA C22.2 No. 0

CAN/CSA C22.2 No. 213

Installation BAT-R

Release

07/2020

Control Drawing for BAT-R devices according to Class I, Div. 2 Haz. Locations

Rev.: 1 Document No.: 000170957DNR

Page 1 of 2

Ordinary Location, Non-Hazardous Area,

non-explosive atmosphere

Explosive Atmosphere

Class I, Div. 2 Groups A, B, C, D

Hazardous Location

Power Supply unit type W: 18 V DC – 32 V DC

Power Supply unit type C: 18 V DC – 60 V DC

Power Supply unit type K: 88 V AC – 265 V AC or 48 V DC – 320 V DC

The earth conductor must be at least the

same wire size (mm² or AWG) as the

supply conductors.

Relay contacts. Equipment with nonincendive  eld wiring parameters. Polarity is not relevant.

THE RELAY TERMINALS ARE DEPENDENT UPON

THE FOLLOWING ENTITY PARAMETERS:

= 30 V I

= 90 mA L

= 1 ȝH C

= 2 nF

WARNING! The USB is for temporary connection only, for maintenance use. Do not use,

connect or disconnect unless the area is known to be non-hazardous. Connection or disconnec-

tion in an explosive atmosphere could result in an explosion!

Relay

USB

BAT-R WLAN Access Point/Client

Installation BAT-R

Release

07/2020

Control Drawing for BAT-R devices according to Class I, Div. 2 Haz. Locations

Rev.: 1 Document No.: 000170957DNR

Page 2 of 2

For Use in Hazardous Locations Class I, Division 2 Groups A, B ,C ,D:

Only allowed for BAT-R model No´s. which are individually labelled “FOR USE IN HAZARDOUS LOCATIONS”

Nonincendive field wiring circuits must be wired in accordance with the National Electrical Code (NEC), NFPA 70 , article 501.

WARNING – EXPLOSION HAZARD – SUBSTITUTION OF ANY COMPONENTS MAY IMPAIR SUITABILITY FOR HAZAR-

DOUS LOCATIONS OR EXPLOSIVE ATMOSPHERES.

WARNING – EXPLOSION HAZARD – DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF

OR THE AREA IS KNOWN TO BE NONHAZARDOUS.

Notes:

The nonincendive  eld wiring circuit concept allows interconnection of nonincendive  eld wiring apparatus and associated nonincendive  eld

wiring apparatus using any of the wiring methods permitted for unclassi ed locations when certain parametric conditions are met.

Capacity: C

or C

 C

+ C

Cable

;

Inductivity: L

or L

 L

+ L

Cable

Temperature Code: T4

Ambient Temperature rating:

Ta : 0 °C to +60°C for “S” temperature types

Ta: í40°C to +70°C for “T” or “E” temperature types

(Refer to the temperature code of the type designation on the device.)

Installation BAT-R

Release

07/2020

 E marking

The labeled devices comply with the regulations contained in the following

European directive(s):

Regulation No. 10 of the Economic Commission for Europe of the United

Nations (UN/ECE): Devices with an approval are labeled with the

E type approval mark.

The optical transceivers M-SFP-SX/LC-EEC and M-SFP-LX/LC-EEC can

be used (relevant for devices with approval characteristic value M).

Devices featuring supply voltage with characteristic value C are not

specified for operation during the motor start phase.

 CE marking

The labeled devices comply with the regulations contained in the following

European directive(s):

2011/65/EU and 2015/863/EU (RoHS)

Directive of the European Parliament and of the Council on the restriction

of the use of certain hazardous substances in electrical and electronic

equipment.

2014/53/EU (RED)

Directive of the European Parliament and of the council on the

harmonization of the laws of the Member States relating to the making

available on the market of radio equipment.

This product may be operated in all EU (European Union)

countries under the condition that it has been configured correctly.

In accordance with the above-named EU directive(s), the EU conformity

declaration will be available to the relevant authorities at the following

address:

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

The product can be used in residential areas (residential, commercial and

light-industrial environments) and in industrial areas.

Installation BAT-R

Release

07/2020

Notes for countries with the following country codes:

 The RED compliance requires compliant operation of the device in the

5 GHz band channels. Compliant operation of the device is achieved

by an unchangeable determination of the country setting. To obtain

RED compliance, perform the work steps described in chapter “Obtain

compliance for operation in the European Union” on page 55.

 Applies to the operation of devices in the 5.6 to 5.65 GHz band:

Install an antenna with an antenna gain of at least 3 dBi.

 Applies to the operation of devices with antennas having a gain of

more than 8 dBi:

At temperatures lower than 13 °F (25 °C) a power reduction of 4 dB

using a software setting has to be applied. This reduction applies in

addition to the antenna gain setting.

 Applies to the operation of antennas having a gain of more than

18 dBi:

For the operation of 5 GHz indoor channels (channels 36 to 64) a

power reduction of 4 dB using a software setting has to be applied.

This reduction applies in addition to the antenna gain setting.

Installation BAT-R

Release

07/2020

 Applies to the operation of the BAT-ANT-N-14G-IP23 antenna:

In addition to the antenna cable supplied, the use of the BAT-CLB-2 N

m-f antenna is required.

See “Accessories” on page 82.

 Applies exclusively to BAT-R device variants featuring Approvals 2

with characteristic value V (SRD):

The maximum radiated power (EIRP) is 25 mW according to

EN 300 440 (Short Range Device).

Notes for Germany (DE), Ireland (IE), and the United Kingdom (UK):

Operation in the 5.8 GHz band at a radiated power (EIRP) >25 mW is

subject to meeting the following conditions:

 Germany (DE)

Frequency range: 5725 MHz to 5875 MHz

Condition: The usage of this band is restricted to commercial public

telecommunication services. Registration at the Federal Network

Agency is required.

Name and website of the competent authority:

Bundesnetzagentur

www.bundesnetzagentur.de

 Ireland (IE)

Frequency range: 5725 MHz to 5875 MHz

Condition: Registration of operational base stations

Name and website of the competent authority:

Commission for Communications Regulation

www.comreg.ie

 United Kingdom (UK):

Frequency range: 5725 MHz to 5850 MHz

Condition: Light-licensing regime

Name and website of the competent authority:

Ofcom

www.ofcom.org.uk

Installation BAT-R

Release

07/2020

 LED or laser components

LED or LASER components according to IEC 60825-1 (2014):

CLASS 1 LASER PRODUCT

CLASS 1 LED PRODUCT

Page is loading ...

Hirschmann BAT-R User manual

Hirschmann BAT-R User manual

Hirschmann BAT-R User manual

Related papers

Other documents