AcuityBrands PHS High Bay Phuzion LED High Bay User manual

AcuityBrands
Brand
AcuityBrands
Model
PHS High Bay Phuzion LED High Bay
Type
User manual
Home » AcuityBrands » AcuityBrands PHS High Bay Phuzion LED High Bay with Uplight Single or Twin
Instruction Manual
PHS High Bay Phuzion LED High Bay with Uplight Single or Twin
Instruction Manual
AcuityBrands PHS High Bay Phuzion LED High Bay with
Uplight Single or Twin Instruction Manual
Manuals+ — User Manuals Simplified.
LED IMPORTANT SAFETY INSTRUCTIONS
Contents
1 PHS High Bay Phuzion LED High Bay with Uplight Single or
Twin
2 Installation and Maintenance Manual
3 Introduction
4 Installation
5 Emergency Lighting
6 Maintenance
7 Limited Warranty and Limitation of Liability
8 Documents / Resources
8.1 References
9 Related Posts
PHS High Bay Phuzion LED High Bay with Uplight Single or Twin
READ AND FOLLOW ALL SAFETY INSTRUCTIONS!
SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION
To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts,
cuts/abrasions, and other hazards please read all warnings and instructions included with and on the fixture
box and all fixture labels.
Before installing, servicing, or performing routine maintenance upon this equipment, follow these general
precautions.
Installation and service of luminaires should be performed by a qualified licensed electrician.
Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construction and
operation and any hazards involved. Regular fixture maintenance programs are recommended.
It will occasionally be necessary to clean the outside of the refractor/lens. Frequency of cleaning will depend on
ambient dirt level and minimum light output which is acceptable to user. Refractor/lens should be washed in a
solution of warm water and any mild, non-abrasive household detergent, rinsed with clean water and wiped
dry.
Should optical assembly become dirty on the inside, wipe refractor/lens and clean in above manner, replacing
damaged gaskets as necessary.
DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should
have been damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly
should be replaced.
Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov.
These instructions do not purport to cover all details or variations in equipment nor to provide every possible
contingency to meet in connection with installation, operation, or maintenance. Should further information be
desired or should particular problems arise which are not covered sufficiently for the purchaser’s or owner’s
purposes, this matter should be referred to Acuity Brands Lighting, Inc.
WARNING
RISK OF ELECTRIC SHOCK
Disconnect or turn off power before installation or servicing.
Verify that supply voltage is correct by comparing it with the luminaire label information.
Make all electrical and grounded connections in accordance with the National Electrical Code (NEC) and any
applicable local code requirements.
All wiring connections should be capped with UL approved recognized wire connectors.
CAUTION
RISK OF INJURY
Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or
performing maintenance.
Avoid direct eye exposure to the light source while it is on.
WARNING
RISK OF BURN
Allow lamp/fixture to cool before handling. Do not touch enclosure or light source.
Follow all manufacturer’s warnings, recommendations and restrictions for: driver type, burning position,
mounting locations/methods, replacement and recycling.
CAUTION
RISK OF FIRE
Keep combustible and other materials that can burn, away from lamp/lens.
Do not operate in close proximity to persons, combustible materials or substances affected by heat or drying.
CAUTION: RISK OF PRODUCT
DAMAGE
Never connect components under load.
Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation.
Unless individual product specifications deem otherwise: Never connect an LED product directly to a dimmer
packs, occupancy sensors, timing devices, or other related control devices. LED fixtures must be powered directly
off a switched circuit.
Unless individual product specifications deem otherwise: Do not restrict fixture ventilation. Allow for some
volume of airspace around fixture. Avoid covering LED fixtures with insulation, foam, or other material that will
prevent convection or conduction cooling.
Unless individual product specifications deem otherwise: Do not exceed fixtures maximum ambient
temperature.
Only use fixture in its intended location.
Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be worn
during all installation or servicing of the unit.
Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter performance.
Some components inside the fixture may not be serviceable. In the unlikely event your unit may require
service, stop using the unit immediately and contact an ABL representative for assistance.
Always read the fixtures complete installation instructions prior to installation for any additional fixture specific
warnings.
Failure to follow any of these instructions could void product warranties. For a complete listing of product Terms
and Conditions, please visit www.acuitybrands.com.
Our Brands
Indoor/Outdoor
Lithonia Lighting
Carandini
Holophane
RELOC
Indoor Lighting
Gotham
Mark Architectural Lighting
Peerless
Renaissance Lighting
Winona Lighting
Outdoor Lighting
American Electric Lighting
Antique Street Lamps
Hydrel
Tersen
Acuity Brands Lighting, Inc. assumes no responsibility for claims arising out of improper or careless installation or
handling of its products.
ABL LED General Warnings, Form No. 503.203
© 2011 Acuity Brands Lighting, Inc. All rights reserved. 12/01/11
Installation and Maintenance Manual
Introduction
1.1 Product Description.
The Phuzion PHS LED fixtures have been designed and tested in accordance with applicable UL/CSA standards
and are suitable for use in Damp locations. Max fixture weight is 50 lbs.
1.2 Alternate Information Sources.
Holophane
Field Service Department
P.O. Box 3004
Newark, OH 43058-3004
(740) 345-9631
Installation
2.1 Tools and Materials Required.
TABLE 1. Installation Tools and Materials
DESCRIPTION USE
5/16” socket Set Screw and Access Door
2.2 P/PM Mounting type (Pendant) (Figures 2 and 3)
2.2.1 Install fixture onto ¾” NPT or NPS rigid conduit, minimum 6 turns until tight. Rigid conduit must be mounted
to a suitable structure capable of supporting the full weight of the luminaire in accordance with local codes.
2.2.1 Tighten set screw to 25-35 in-lb.
WARNING
FAILURE TO TIGHTEN SET SCREW COULD CAUSE FIXTURE TO FALL RESULTING IN INJURY, DEATH OR
SERIOUS PROPERTY DAMAGE.
2.2.2 Open electrical door by loosening (4) door screws enough to lift door off keyhole slots. Rotate 180 degrees
and hang off (2) of the door screws previously loosened.
2.2.3 Make all supply wire connections in accordance with all local electrical codes.
2.2.3.1 For a Holophane Phuzion luminaire that will also be wired to a separately installed Holophane Remote
Emergency Battery Pack (PS30250/PS20250T20C), STOP. Do not make standard, supply wire connections.
Proceed to Section 3 of this instruction manual for specific instructions.
2.2.4 Re-install electrical door and tighten door screws, ensuring all leads are completely inside enclosure and not
pinched. If any foreign body is pinched between the door and housing, the housing may not seal properly
2.2.5 Energize power to the fixture and check for proper operation.
2.3 N/NDT/NR Mounting type (Non-Disconnect) (see figures 4 and 5)
2.3.1 For NR mount N Hanger reused from existing installation. Skip to step 2.3.5.
2.3.2 Loosen the captive wing nut, disengage the J-bolt and remove the N Hanger.
2.3.3 For pendant mounting, remove plug and install the N Hanger on ¾” NPT or NPS rigid conduit minimum 4
turns and until tight. Securely tighten the setscrew inside the hanger to 25-35 in-lb. See warning 2.2.1.
2.3.4 For ceiling mounting, remove the knockout(s) for side entry or through-wiring. Drill through at the four drill
spots on the top of the hanger with a 9/32” diameter drill bit. Mount the hanger to the ceiling or girder with (4) ¼”
bolts. Install conduit, conduit nuts and conduit bushing, and tighten securely.
2.3.5 Hang fixture on the N/NDT Hanger hinge and make wiring connections in accordance with all local electrical
codes.
2.3.6 Swing the fixture up, latch the J-bolt to the hanger and secure with the captive wing nut. Hand tighten the
wing nut only, without the use of a tool.
2.3.7 Attach label(s) provided with fixture to N/NDT Hanger in location shown.
2.3.8 Energize power to the fixture and check for proper operation.
2.4 Q/QD/QR Mounting type (Quick Disconnect) (see figure 6)
Note
The Q/QD mounting-type may be installed only to a Holophane QDH Quick Disconnect Hanger. The QDH hanger
and installation instructions are shipped separately. Install the QDH hanger following those instructions before
proceeding with installation of the fixture. For QR mount, QDH Hanger is reused from existing installation.
2.4.1 Hang fixture on QDH hanger hinge.
2.4.2 Swing the fixture up, latch the J-bolt to the hanger, and secure the ballast assembly with the captive wing
nut. Hand tighten the wing nut only, without the use of a tool.
2.4.3 Attach label(s) provided to QDH Hanger in location shown.
2.4.4 Energize power to the fixture and check for proper operation.
2.5 P/PM Mounting type with Hook or Loop Option
(see figure 7)
2.5.1 Hang the fixture on a hook or loop that is properly sized and attached to support the weight of the luminaire.
2.5.2 If the hanging hook is provided with a spring tab retainer, be certain the tab has snapped closed against the
inside of the hook.
2.5.3 If the hanging hook is provided with a retainer screw, tighten the retaining screw until it is snug to prevent it
from backing out.
2.5.4 Make all supply wire connections in accordance with all local electrical codes.
2.5.4.1 For a Holophane Phuzion luminaire that will also be wired to a separately installed Holophane Remote
Emergency Battery Pack (PS30250/PS20250T20C), STOP. Do not make standard, supply wire
connections.Proceed to Section 3 of this instruction manual for specific instructions.
2.5.5 Energize power to the fixture and check for proper operation.
2.6 Dimming Terminal Option (see figure 2)
2.6.1 Connect dimming leads to the terminal block matching + Violet and – Pink or Gray leads. It is necessary to
connect dimming leads with proper polarity, (+ Violet, – Pink or Gray).
2.7 Safety Chain Option (see figures 8A and 8B)
2.7.1 The safety chain option is pre-attached to the luminaire and is provided with additional hardware to attach
the other end of chain to the building structure. As shown, two additional bosses are available should installer
need to relocate chain or to attach with two additional points of attachment. Note leave no more than three inches
of slack in the chain between building structure and luminaire. Leaving more slack will allow a longer free-fall,
resulting in a larger impact and possible structural failure.
WARNING
LEAVE NO MORE THAN THREE INCHES OF SLACK IN THE CHAIN WHEN ATTACHING TO THE BUILDING
STRUCTURE. LEAVING MORE SLACK WILL ALLOW A LONGER FREE-FALL, A RESULTING LARGER IMPACT
LOAD AND POSSIBLE STRUCTURAL FAILURE. FAILURE TO INSTALL THE CHAIN AS INSTRUCTED MAY
RESULT IN INJURY OR DEATH OR SIGNIFICANT PROPERTY DAMAGE.
Emergency Lighting
3.1 Emergency Maximum Mounting Height
PhuzionTM Luminaires equipped with emergency battery backup systems may be mounted no higher than
indicated in Table 2 to comply with UL924 requirements.
Table 2: Emergency mounting height
Lumen Package
Max. Mounting Height (ft)
PS30250
12L 32
18L 60
24L 60
30L 40
35L 40
40L 40
45L 40
3.2 Installation of PS30250 Battery Backup
CAUTION: A potential electrical hazard exists even when AC power supply has been turned off. Disconnect
Battery Connector (2 red leads) before servicing.
IMPORTANT NOTES: Make sure that branch circuit feeds are derived from a common phase for both normal
lighting driver and PS30250 prior to installation.
The PS30250 can be used with a switched or unswitched (night) circuit. When used with a switched fixture it is
important to note that the power to the PS30250 inverter/charger must be provided by an unswitched circuit.
APPROXIMATE WORKING VOLTAGE
Inverter/charger input: 120 OR 277 VAC
3.2.1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS
3.2.2. Before wiring to power supply, turn off electricity at fuse or circuit breaker.
3.2.3. To reduce the risk of electrical shock, disconnect AC power and unplug red battery connector before
servicing.
3.2.4. All servicing should be performed by qualified personnel.
3.2.5. Consult your local building code for approved wiring and installation.
3.2.6. Do not use outdoors. This product is for use with indoor fixtures except air handling heated outlets, and wet
or hazardous location fixtures.
3.2.7. The LED emergency driver must be connected to an unswitched AC power source (120 or 277 volts).
3.2.8. Do not mount near gas or electric heater.
3.2.9. Equipment should be mounted in location and at heights where it will not readily be subjected to tampering
by unauthorized personnel.
3.2.10. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
3.2.11 Do not use this equipment for other than intended use.
SAVE THESE INSTRUCTIONS INSTALLATION PROCEDURE
3.2.12 Inspect PS30250 and make sure the battery connector (2 red leads) are not connected.
3.2.13 Once luminaire is installed, mount the remote PS30250 Emergency Battery Pack securely to ceiling or
other solid surface.
3.2.14 Install the Junction box with test switch and indicator light.
3.2.15 This unit has more than one power supply connection point. To reduce the risk of electrical shock,
disconnect both the branch circuit breakers or fuse and emergency power supplies before servicing.
3.2.16 Make connections to “Switched” and “Unswitched” power within the junction box (Fig 8).
3.2.17 Apply continuous power to PS30250.
3.2.18 Connect the battery connector (red leads).
NOTE: Do not mount Emergency Battery Pack over A.C. Ballast.
Figure 8
Maintenance
4.1 Electrical Component Replacement (Driver, Surge protector) (Figure 3)
4.1.1 Open electrical door by loosening (4) door screws enough to lift door off keyhole slots. Do not completely
remove the door screws.
4.1.2 Rotate 180 degrees and hang off (2) of the door screws previously loosened.
4.1.3 Tag leads before disconnecting.
4.1.4 Replace components using Holophane approved replacement parts.
4.1.5 Re-connect electrical leads
4.1.6 Re-install access door and tighten door screws, ensuring all leads are completely inside enclosure and not
pinched.
4.2 Sensor Replacement (Figure 10)
4.2.1 Disconnect power to the luminaire location before maintenance.
4.2.2 Open electronics door and tag leads before disconnecting.
4.2.3 Release cord strain relief on top side of optical housing and remove sensor cord from fixture.
4.2.4 Removed sensor conduit body from optical housing.
4.2.5 Replace components using Holophane approved replacement parts.
4.2.6 Re-connect electrical leads
4.2.7 Re-install the sensor ensuring leads are completely inside the enclosure and not pinched. Re-install sensor
frame over sensor.
Limited Warranty and Limitation of Liability
5-year limited warranty. Complete warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_Conditions.aspx.
Acuity Brands Lighting, Inc.
3825 Columbus Rd., Granville, OH 43023
IM-369-F 9/21 ©2021 Acuity Brands Lighting, Inc.
All Rights Reserved.
Visit our web site at www.holophane.com
Documents / Resources
AcuityBrands PHS High Bay Phuzion LED High Bay with Uplight Single or Twin [pdf] Instr
uction Manual
PHS High Bay Phuzion LED High Bay with Uplight Single or Twin, PHS High Bay, Phuzion LED
High Bay with Uplight Single or Twin, High Bay with Uplight Single or Twin, Uplight Single or Twi
n, Single or Twin, Twin
References
Acuity Brands | Lighting, Controls, and Building Management Solutions
Page Not Found
U.S. Environmental Protection Agency | US EPA
Holophane | Lighting solutions for commercial, industrial, emergency and outdoor applications.
Manuals+,
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

AcuityBrands PHS High Bay Phuzion LED High Bay User manual

AcuityBrands
Brand
AcuityBrands
Model
PHS High Bay Phuzion LED High Bay
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents