2. Energy Suspension
  3. 31mm Front Sway Bar Bushings

Energy Suspension 31mm Front Sway Bar Bushings Installation guide

  • Hello! I've reviewed the provided instruction for installing Energy Suspension polyurethane rod-eye/track bar bushings. The document details how to properly remove old bushings, clean the mounting area, and install the new polyurethane bushings using grease. I can help with any questions about the installation process or the specific steps outlined in the instructions.
  • What should be done before installing the polyurethane bushings?
    Where should grease be applied when installing polyurethane bushings?
    What do I need to do if the original bushings have an outer metal shell?
17073 1/NOV/00 BRH
Updated 17/JAN/02 BRH
Updated 11/JUL/03 BRH
Universal Instructions
for rod-eye / track bar bushings
Sleeve
Bushing
Rod-eye
REMEMBER: Some O.E. bushings use an outer metal shell,
this outer shell must be removed.
ONE PIECE STYLE BUSHINGONE PIECE STYLE BUSHING
(NOTE: If not supplied
in set, original sleeve/
shoulder bolt must
be re-used.)
Face of
bushing
Sleeve
Bushing
Rod-eye
REMEMBER: Some O.E. bushings use an outer metal shell,
this outer shell must be removed.
TWO PIECE STYLE BUSHINGTWO PIECE STYLE BUSHING
Bushing
Face of
bushing
(NOTE: If not supplied
in set, original sleeve/
shoulder bolt must
be re-used.)
1131 VIA CALLEJON, SAN CLEMENTE, CA 92673
R
It is recommended that if you are unfamiliar with this type of work that you refer to a qualified service center specializing in this type of work.
It is also recommended that if you choose to do this work yourself that a factory service manual be obtained for the proper procedures
pertaining to removal, replacement and proper torque specifications for your vehicle. This instruction set is intended as a guideline for the
safe installation of Energy Suspension’s polyurethane bushings, once you have removed the factory components from your vehicle.
Updated 8/JAN/03 BRH
2003 Energy Suspension. All rights reserved.2003 Energy Suspension. All rights reserved.
CC
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
Remove original rubber, clean I.D. of eye of any old rubber or rust. When installing polyurethane bushings, apply grease as instructed:
Apply light coat of grease to I.D. of the rod-eye. Apply light coat of grease to the I.D. and O.D. of bushings (all surfaces that contact metal).
Apply light coat of grease to the O.D. of sleeve. Apply light coat of grease to the faces of the bushings after they are installed.
17073 1/NOV/00 BRH
Updated 17/JAN/02 BRH
Updated 11/JUL/03 BRH
Universal Instructions
for rod-eye / track bar bushings
Sleeve
Bushing
Rod-eye
REMEMBER: Some O.E. bushings use an outer metal shell,
this outer shell must be removed.
ONE PIECE STYLE BUSHINGONE PIECE STYLE BUSHING
(NOTE: If not supplied
in set, original sleeve/
shoulder bolt must
be re-used.)
Face of
bushing
Sleeve
Bushing
Rod-eye
REMEMBER: Some O.E. bushings use an outer metal shell,
this outer shell must be removed.
TWO PIECE STYLE BUSHINGTWO PIECE STYLE BUSHING
Bushing
Face of
bushing
(NOTE: If not supplied
in set, original sleeve/
shoulder bolt must
be re-used.)
1131 VIA CALLEJON, SAN CLEMENTE, CA 92673
R
It is recommended that if you are unfamiliar with this type of work that you refer to a qualified service center specializing in this type of work.
It is also recommended that if you choose to do this work yourself that a factory service manual be obtained for the proper procedures
pertaining to removal, replacement and proper torque specifications for your vehicle. This instruction set is intended as a guideline for the
safe installation of Energy Suspension’s polyurethane bushings, once you have removed the factory components from your vehicle.
Updated 8/JAN/03 BRH
2003 Energy Suspension. All rights reserved.2003 Energy Suspension. All rights reserved.
CC
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
Remove original rubber, clean I.D. of eye of any old rubber or rust. When installing polyurethane bushings, apply grease as instructed:
Apply light coat of grease to I.D. of the rod-eye. Apply light coat of grease to the I.D. and O.D. of bushings (all surfaces that contact metal).
Apply light coat of grease to the O.D. of sleeve. Apply light coat of grease to the faces of the bushings after they are installed.
/