BMW 84 64 0 026 614 Installation Instructions Manual

Brand: BMW

Model: 84 64 0 026 614

Type: Installation Instructions Manual

This manual is also suitable for

84 64 0 025 810

BMW 84 64 0 026 614

This retrofit kit enables the installation of a Nokia hands-free facility in your BMW 7 Series (E38) LHD, enhancing your in-car communication experience.

With this kit, you can seamlessly integrate your Nokia mobile phone with your vehicle's audio system, allowing you to make and receive calls while keeping your hands on the wheel. The hands-free module connects to your phone via Bluetooth, providing a stable and convenient wireless connection.

The kit includes all the necessary components for installation, including the hands-free control module, microphone, wiring harness, and mobile phone holder. Detailed instructions guide you through the installation process, ensuring a professional and secure fit.

BMW 84 64 0 026 614

This retrofit kit enables the installation of a Nokia hands-free facility in your BMW 7 Series (E38) LHD, enhancing your in-car communication experience.

F 38 0175 B

Retrofit kit for Nokia hands-free facility

BMW 7 Series (E38) LHD

These installation instructions are only valid for cars up to a production date of 9/00.

Specialist and electrical knowledge required.

Installation time 1 hour, depending on the condition of the car and the equipment in it.

Retrofit / Installation kit No. 84 64 0 025 810

Parts and Accessories

Installation Instructions

Retrofit / Installation kit No. 84 64 0 025 810, 84 64 0 026 614 Issue date: 07.2000

Installation instructions No. 01 29 0 025 833

84 64 0 026 614

Table of contents

Section Page

1. Important information for the installation of the Nokia hands-free facility ....................26

2. Preparations ................................................................................................................27

3. Parts overview..............................................................................................................28

4. Connection overview....................................................................................................30

5. Installation and wiring diagram (for cars with SA 640 telephone preparation only) ......32

6. Installation and wiring diagram (for cars without SA 640 telephone preparation only) ..33

7. To install the microphone ............................................................................................34

8. To install and connect the adapter wiring harness, aerial adapter cable and

telephone adapter cable in cars with SA 640 telephone preparation ..........................35

9. To install and connect the adapter wiring harness in cars without SA 640 telephone

preparation ..................................................................................................................38

10. To install the mobile phone holder with connection cable on the telephone console ..39

11. To install the telephone console with the fitted mobile phone with connection cable ..40

12. To connect and install the hands-free facility control module ......................................41

13. To prepare and install the right-hand footwell trim ......................................................43

14. Coding and concluding work ......................................................................................44

15. Circuit diagram for adapter wiring harness ..................................................................45

16. Circuit diagram for telephone adapter cable (cars with SA 640 telephone

preparation only) ..........................................................................................................47

Retrofit / Installation kit No. 84 64 0 025 810, 84 64 0 026 614 Issue date: 07.2000

Installation instructions No. 01 29 0 025 833

1. Important information for the installation of the Nokia hands-free facility

Only for use within the BMW dealer organisation.

The Nokia hands-free facility may only be installed by a specialist workshop that has the

required special tools and manuals (servicing, repair, diagnostics, etc.).

Ensure that the cables/lines are not kinked or damaged as you install them in the car.

Additional cables/lines that you install must be secured with cable ties.

Item numbers refer only to the overview drawings and to the texts next to the

appropriate figure.

The hands-free facility is only functional when the ignition key is in position ”R” or beyond

on cars that have the SA 677 Professional (DSP) hi-fi system.

The adapter cable kit must also be ordered separately for cars with SA 640 telephone

preparation using the electronic parts catalogue (EPC).

Subject to technical modifications

Tools and equipment required

MoDIC III or DIS Step drills up to 20 mm in diameter

Set of Philips screwdrivers Set of twist drill bits

Set of straight slot screwdrivers Cable lamp

1/4 inch socket set Adhesive textile tape

Set of Allen keys Drill

Angle cutter Double-sided adhesive tape

GB/26

Retrofit / Installation kit No. 84 64 0 025 810, 84 64 0 026 614 Issue date: 07.2000

Installation instructions No. 01 29 0 025 833

2. Preparations

TIS instruction No.

Conduct a short test (print out the error memory).

Disconnect the battery. 12 00 ...

Remove the front centre armrest. 51 16 200

Remove the trim on the selector lever. 51 16 210

Remove the centre console insert and trim. 51 16 200

Remove the right-hand footwell trim.

Remove the centre console trim at the front right. 51 16 200

Remove the microphone trim. 51 44 011

Retrofit / Installation kit No. 84 64 0 025 810, 84 64 0 026 614 Issue date: 07.2000

Installation instructions No. 01 29 0 025 833

GB/27

1 2 3 4 5 6

7 8 9

1211 1310 14

18 19 201716

21 22 23

F 38 0176 B

3. Parts overview

GB/28

Retrofit / Installation kit No. 84 64 0 025 810, 84 64 0 026 614 Issue date: 07.2000

Installation instructions No. 01 29 0 025 833

1. Mobile phone holder with connection cable

2. Hands-free facility control module

3. Mounting plate

4. Cover cap for mobile phone holder

5. Cover cap for hands-free facility control module

6. Pan head screw M4 x 15

7. Adapter wiring harness

8. Microphone

9. Aerial adapter cable*

10. Protective strip* (for cars with SA 640 telephone preparation only)

11. Telephone adapter cable* (for cars with SA 640 telephone preparation only)

12. 5 A fuse*

13. Black socket casing*

14. Protective strip (two)

15. Cable ties (ten)

16. Fillister head self-tapping screw 2.9 x 16 (four)

17. Dual lok securing strip, coarse (supplied in a length of 300 mm, must be cut into

two lengths of 100 mm)

18. Dual lok securing strip, fine (supplied in a length of 300 mm, must be cut into two

lengths of 100 mm)

19. Spacer (two)

20. Hexagonal screw with washer M5 x 30 (two)

21. Speed nut M5 (two)

22. Damping strip

23. Telephone console

The parts marked with an asterisk (*) are not supplied with the parts kit and must be ordered

separately using the electronic parts catalogue (EPC) to suit the equipment in the car.

GB/29

Retrofit / Installation kit No. 84 64 0 025 810, 84 64 0 026 614 Issue date: 07.2000

Installation instructions No. 01 29 0 025 833

3. Parts overview

4. Connection overview

GB/30

Retrofit / Installation kit No. 84 64 0 025 810, 84 64 0 026 614 Issue date: 07.2000

Installation instructions No. 01 29 0 025 833

Adapterkabelbaum

Black 18-pin plug casing

White 6-pin plug casing

2-pin pawl plug, 2.5 mm in

diameter

2-pin pawl plug 3.5 mm in

diameter

White 6-pin socket casing

Cars with SA 640 telephone preparation

To black 18-pin socket casing X4545B on the telephone wiring

harness under the centre console insert with trim

Cars without SA 640 telephone preparation

To black 18-pin socket casing on the basic wiring harness under

the centre console insert with trim.

Cars with SA 640 telephone preparation

To black 6-pin socket casing X4546B on the telephone wiring

harness under the centre console insert with trim

Cars without SA 640 telephone preparation

Insulate and tie back.

To grey socket casing, Ø 2.5 mm in diameter, on the hands-free

facility control module (2) behind the glove compartment.

To grey socket casing, Ø 3.5 mm in diameter, on the hands-free

facility control module (2) behind the glove compartment.

To white 6-pin plug casing on the hands-free facility control

module (2) behind the glove compartment.

Position Description Cable colour Connection location in the car

F 38 0177 B

Telephone adapter cable D is only required for cars with SA 640 telephone preparation.

Mobile phone holder with

connection cable

Transparent 15-pin plug casing,

Western plug

Coaxial plug casing FME

black

To black 15-pin socket casing, Western plug, on the hands-free

facility control module (2) behind the glove compartment

To branch B2, coaxial socket casing FME on the aerial adapter

cable B in the footwell on the passenger side or, on cars without

SA 640 telephone preparation, to the aerial cable in the footwell

on the passenger side

Telephone adapter cable

Black 1-pin plug casing

1-pin socket contact

1-pin blade terminal contact

Black socket casing

red/black/yellow

red/yellow

To the black 1-pin socket casing (13) with connected 1-pin

socket contact PIN 2, red/black/yellow cable, on the white 3-pin

socket casing for the cigarette lighter plug connector X531 under

the centre console insert with trim

To the white 3-pin socket casing for the cigarette lighter plug

connector X531 under the centre console insert with trim in

PIN 2

To the black 18-pin socket casing X4545B on the telephone

wiring harness under the centre console insert with trim in

PIN 10

Connect to the released, disconnected 1-pin socket contact

PIN 2, red/black/yellow cable, on the white 3-pin socket casing

for the cigarette lighter plug connector X531 under the centre

console insert with trim

Telephone adapter cable B is only required for cars with SA 640 telephone preparation.

Retrofit / Installation kit No. 84 64 0 025 810, 84 64 0 026 614 Issue date: 07.2000

Installation instructions No. 01 29 0 025 833

GB/31

4. Connection overview

Aerial adapter cable

Coaxial socket casing mini

UHF

Coaxial socket casing FME

black

To coaxial plug casing mini UHF on the telephone wiring harness

under the centre console insert with trim

To branch C2, coaxial plug casing FME on the mobile phone

holder with connection cable C in the footwell on the passenger

side

F 39 0178 B

5. Installation and wiring diagram

(for cars with SA 640 telephone preparation only)

Retrofit / Installation kit No. 84 64 0 025 810, 84 64 0 026 614 Issue date: 07.2000

Installation instructions No. 01 29 0 025 833

GB/32

The adapter wiring harness A, the aerial adapter cable B, the mobile phone holder connection

cable C and the telephone adapter cable D are to be installed as shown in the figure and

secured with cable ties.

When installing the adapter wiring harness A and the aerial adapter cable B, start with

branches A1 and A2 or B1.

Branches A1 and A2 to the centre console on the right near the heating duct

Branches A3, A4 and A5 along the gearbox tunnel within the centre console to the

installation location of the hands-free facility control module behind the glove compartment

Branch B1 to the centre console on the right near the heating duct

Branch B2 to the footwell on the passenger side

Branch C1 to the installation location of the hands-free facility control module behind the

glove compartment

Branch C2 to the footwell on the passenger side

Branches D1 and D2 to the cigarette lighter plug connector X531 under the centre console

insert with trim

Branch D3 on the right near the heating duct

Tie back any excess lengths.

F 39 0179 B

6. Installation and wiring diagram

(for cars without SA 640 telephone preparation only)

Retrofit / Installation kit No. 84 64 0 025 810, 84 64 0 026 614 Issue date: 07.2000

Installation instructions No. 01 29 0 025 833

GB/33

The adapter wiring harness A and the mobile phone holder connection cable C are to be

installed as shown in the figure and secured with cable ties.

When installing the adapter wiring harness A, start with branches A1 and A2.

Branches A1 and A2 to the centre console on the right near the heating duct

Branches A3, A4 and A5 along the gearbox tunnel within the centre console to the

installation location of the hands-free facility control module behind the glove compartment

Branch C1 to the installation location of the hands-free facility control module behind the

glove compartment

Branch C2 to the footwell on the passenger side

Tie back any excess lengths.

Retrofit / Installation kit No. 84 64 0 025 810, 84 64 0 026 614 Issue date: 07.2000

Installation instructions No. 01 29 0 025 833

Cars without a sunroof only

Release the microphone trim (30) from the

hands-free facility frame (31) in the headlining

(32).

Pull the black 3-pin socket casing (33) out

through the opening (34) in the headlining (32)

connect it to the black 3-pin plug casing of the

microphone (8).

Clip the microphone (8) into the microphone trim

(30).

Refer to the direction of the arrows on the

microphone trim (30) and microphone (8) (the

arrows must point to the front of the car).

Then secure the microphone trim (30) in the

hands-free facility frame (31) in the headlining

(32).

7. To install the microphone

F 38 0180 B

GB/34

Cars with a sunroof only

Release front headlining trim (30) from the

headlining (31).

Pull the black 3-pin socket casing (32) out

through the opening (33) in the headlining (31)

connect it to the black 3-pin plug casing of the

microphone (8).

Clip the microphone (8) into the microphone trim

(34).

Refer to the direction of the arrows on the

microphone trim and microphone (8) (the arrows

must point to the front of the car).

Then secure the front headlining trim (30) in the

headlining (31).

F 38 0181 B

Retrofit / Installation kit No. 84 64 0 025 810, 84 64 0 026 614 Issue date: 07.2000

Installation instructions No. 01 29 0 025 833

Release the 3-pin socket casing (30) on the

cigarette lighter plug connector X531.

Disconnect the existing socket contact (31) from

slot PIN 2, red/black/yellow cable on the white 3-

pin socket casing (30) on the cigarette lighter

plug connector X531.

Connect branch D2, 1-pin socket contact,

red/black/yellow cable on the telephone adapter

cable D, to the white 3-pin socket casing (30) on

the cigarette lighter plug connector X531 in the

released slot PIN 2.

Connect the black socket casing (13) to the

released disconnected socket contact (31) and

connect this assembly to branch D1, black 1-pin

plug casing, red/black/yellow cable on telephone

adapter cable D.

Then secure the white 3-pin socket casing (30)

again and insert the 5 A fuse (12) into the fuse

holder (32).

8. To install and connect the adapter cable in cars with SA 640 telephone

preparation

F 38 0182 B

X531 12

GB/35

Thread the black 18-pin socket casing X4545B,

black 6-pin socket casing X4546B and the

coaxial plug casing mini UHF (30) on the

telephone wiring harness (31) through the

opening (32) towards the front (on the right near

the heating duct (33).

F 38 0183 B

X4545B

X4546B

X4545B

X4546B

8. To install and connect the adapter cable in cars with SA 640 telephone preparation

Retrofit / Installation kit No. 84 64 0 025 810, 84 64 0 026 614 Issue date: 07.2000

Installation instructions No. 01 29 0 025 833

Dismantle the black 18-pin socket casing

X4545B on the tied back telephone wiring

harness (30).

Connect branch D3, 1-pin blade terminal

contact, red/yellow cable on telephone adapter

cable D, to slot PIN 10 on the black 18-pin

socket casing X4545B.

If slot PIN 10 on the black 18-pin socket casing

X4545B is already occupied the existing blade

terminal contact (31) must be taken out of slot

PIN 10 on the black 18-pin socket casing

X4545B, the contact part cut off and the free

cable end insulated with a shrink hose (this is

no longer required).

Then assemble the black 18-pin socket casing

X4545B again.

F 38 0184 B

X4545B

GB/36

Press the centre console (30) outwards a little

from the inside and thread branches A1, black

18-pin plug casing, A2, white 6-pin plug casing

on adapter wiring harness A and B1, coaxial

socket casing mini UHF on the aerial adapter

cable B, through it.

F 38 0206 B

8. To install and connect the adapter cable in cars with SA 640 telephone preparation

Connect branch A1, black 18-pin plug casing on

the adapter wiring harness A to the black 18-pin

socket casing X4545B on the telephone wiring

harness (30).

Connect branch A2, white 6-pin plug casing on

the adapter wiring harness A to the black 6-pin

socket casing X4546B on the telephone wiring

harness (30).

Screw branch B1, coaxial socket casing mini

UHF on the aerial adapter cable B to the coaxial

plug casing mini UHF (31) on the telephone

wiring harness (30).

Then lay the adapter wiring harness A with

branches A3, A4 and A5 along the gearbox

tunnel (32) within the centre console (33) to the

installation site for the hands-free facility control

module behind the glove compartment and lay

the aerial adapter cable B with branch B2 along

the gearbox tunnel (32) within the centre console

(33) to the right-hand footwell.

Affix the protective strip (14) to the cable so

that the plug connections (A1 + X4545B), (A2 +

X4546B) and (B1 + 31) are enclosed in it.

When refitting the centre console insert,

ensure that the plug connections and the cables

are not jammed or damaged.

The figure shows the luggage compartment

at the rear left.

Release the tied back telephone wiring harness

(30) and remove the protective strip.

Check whether the coaxial plug casing mini UHF

(31) and the coaxial socket casing mini UHF (32)

are screwed together.

If this is not the case make this connection.The

black 3-pin socket casing (33) on the tied back

telephone wiring harness (30) is only required if

you are fitting a cable compensator.

The black 26-pin socket casing X695B on the

tied back telephone wiring harness (30) is not

required.

Affix the protective strip (10) to the cable so

that it encloses the plug connections (31 + 32),

the black 26-pin socket casing (X695B) and the

black 3-pin socket casing (33).

Then tie back the telephone wiring harness (30)

again.

Retrofit / Installation kit No. 84 64 0 025 810, 84 64 0 026 614 Issue date: 07.2000

Installation instructions No. 01 29 0 025 833

X4545B

X4546B

A3-A5

F 38 0185 B

X695B

F 38 0186 B

GB/37

Connect branch A1, black 18-pin plug casing on

the adapter wiring harness A to the black 18-pin

socket casing (30) on the basic kit retrofit wiring

harness.

Branch A2, white 6-pin plug casing on the

adapter wiring harness A is not required.

Affix the protective strip (14) to the cable so

that the plug connections (A1 + 30) and branch

A2 are enclosed in it.

Lay the adapter wiring harness A with branches

A3, A4 and A5 along the gearbox tunnel (31)

inside the centre console (32) to the installation

site of the hands-free facility control module

behind the glove compartment and secure it with

cable ties.

9. To install and connect the adapter wiring harness in cars without SA 640

telephone preparation

X4545B

A3-A5

F 38 0187 B

Retrofit / Installation kit No. 84 64 0 025 810, 84 64 0 026 614 Issue date: 07.2000

Installation instructions No. 01 29 0 025 833

GB/38

Mark the hole (30) through which to thread the

connection cable from the mobile phone holder

with dimension A on the telephone console (23).

Dimension A = 70 mm

Predrill the hole with a Ø 6 mm twist drill bit and

then enlarge it with a Ø 20 mm step drill.

F 38 0188 B

Align the mounting plate (3) in the centre so that

the 20 mm hole (30) you have just drilled is half

covered.

Mark the four securing holes (31) and remove the

mounting plate (3) again.Then drill the marked

securing holes (31) in the telephone console with

a 2.4 mm twist drill bit.

F 38 0189 B

Retrofit / Installation kit No. 84 64 0 025 810, 84 64 0 026 614 Issue date: 07.2000

Installation instructions No. 01 29 0 025 833

10. To install the mobile phone holder with connection cable on the telephone

console

GB/39

Push branch C1, transparent 15-pin plug casing,

Western plug, and branch C2, coaxial plug

casing FME, on the mobile phone holder C

through the hole (30) in the telephone console

(23).

Secure the mounting plate (3) on the telephone

console (23) using the four fillister head self-

tapping screws 2.9 x 16 (16) and secure the

module phone holder with connection cable (1)

to the mounting plate (3) using the pan head

screw M4 x 15 (6).

Then secure the cover cap for the mobile phone

holder (4) on the mobile phone holder with

connection cable (1).

F 38 0190 B

Align the connection cable on the mobile phone

holder C, as shown in the figure, and secure it to

the telephone console (23) using textile adhesive

tape (30).

F 38 0191 B

Retrofit / Installation kit No. 84 64 0 025 810, 84 64 0 026 614 Issue date: 07.2000

Installation instructions No. 01 29 0 025 833

Install the telephone console as described in the

installation instructions entitled ”BMW telephone

console 7 Series E38”, order No. 01 29 9 789

676.

Install the telephone console as described in

the installation instructions entitled ”BMW

telephone console 7 Series E38”,orderNo.01 29

9 789 676.

Lay branch C1, transparent 15-pin plug casing

on the connection cable C, behind the glove

compartment to the installation location of the

hands-free facility control module.

Screw branch C2, coaxial plug casing FME on

the connection cable C to branch B2, coaxial

socket casing FME on the aerial adapter cable B

or, on cars without SA640 telephone preparation,

to the coaxial socket casing FME (30) on the

basic kit retrofit wiring harness.

Affix the rattling guard (14) on the cable so

that it encloses the screw connection C2 + B2 or

C2 + 30.

11. To install the telephone console with the fitted mobile phone with connection

cable

F 38 0192 B

B2/30

GB/40

Retrofit / Installation kit No. 84 64 0 025 810, 84 64 0 026 614 Issue date: 07.2000

Installation instructions No. 01 29 0 025 833

Clean (degrease) the hands-free facility

control module (2) before affixing the Dual

securing strips.

Cut the 300 mm length of fine Dual securing

strip (18) into two lengths of 100 mm (the rest is

not required).

Affix the two cut lengths of fine Dual securing

strip (18) (100 mm) on to the hands-free facility

control module (2) as shown in the figure.

12. To connect and install the hands-free facility control module

F 38 0193 B

F 38 0194 B

Cut the 300 mm length of coarse Dual securing

strip (17) into two lengths of 100 mm (the rest is

not required).

Press the two cut lengths of coarse Dual

securing strip (17) on to the two lengths of fine

Dual securing strip (18) affixed to the hands-free

facility control module (2).

GB/41

Connect branch C1, transparent 15-pin plug

casing, Western plug, on the mobile phone

holder with connection cable to the grey 15-pin

socket casing (30) on the hands-free facility

control module (2).

Connect branch A3, 2-pin pawl plug with a

diameter of 2.5 mm on the adapter wiring

harness A, to the grey socket casing with a

diameter of 2.5 mm (31) on the hands-free facility

control module (2).

Connect branch A4, 2-pin pawl plug with a

diameter of Ø 3.5 mm on the adapter wiring

harness A, to the grey socket casing with a

diameter of Ø 3.5 mm (32) on the hands-free

facility control module (2).

Connect branch A5, white 6-pin socket casing

on the adapter wiring harness A, to the white

6-pin plug socket casing (33) on the hands-free

facility control module (2).

Then press the cover cap for the hands-free

facility control module (5) on to the hands-free

facility control module (2) and remove the

backing foil (34) from the coarse Dual securing

strip (17) on the hands-free facility control

module (2).

F 38 0195 B

Retrofit / Installation kit No. 84 64 0 025 810, 84 64 0 026 614 Issue date: 07.2000

Installation instructions No. 01 29 0 025 833

12. To connect and install the hands-free facility control module

GB/42

F 38 0196 B

F 38 0197 B

Push the connection cable C and the adapter

wiring harness A behind the centre console (30)

and install the front right centre console trim

(31).

Before affixing the hands-free facility control

module (2) on to the relay holder (30), clean

(degrease) the relay holder (30).

Affix the connected hands-free facility control

module (2) on the relay holder (30) in the

direction indicated by the arrow, in the centre

(right at the front), as shown in the figure.

Lay the connection cable C and the adapter

wiring harness A and secure them with cable

ties (15).

Retrofit / Installation kit No. 84 64 0 025 810, 84 64 0 026 614 Issue date: 07.2000

Installation instructions No. 01 29 0 025 833

13. To prepare and install the right-hand footwell trim

GB/43

F 38 0200 B

Affix the spacer sleeves (19) to the right-hand

footwell trim (30) using double-sided adhesive

tape.

Place a speed nut M5 (21) on the relay holder on

the left in the direction indicated by the arrow.

Place another speed nut M5 (21) on the air duct

(31) on the control module box on the right in the

direction indicated by the arrow.

F 38 0201 B

Secure the right-hand footwell trim (30) with the

two hexagonal screws and washers M5 x 30 (20)

through the affixed spacer sleeves to the

inserted speed nuts.The two plastic expanding

rivets with which the right-hand footwell trim (30)

was originally secured are no longer required.

Then clip the right-hand footwell trim (30) to the

heating duct (31) and secure it with the self-

tapping screw (32).

F 38 0202 B

3132

F 38 0203 B

If the right-hand footwell trim (30) is fitted with a

footwell light (31) or the preparation (32) for

installing a footwell light, the damping strip (22)

must be affixed over this as shown in the figure.

Page is loading ...

BMW 84 64 0 026 614 Installation Instructions Manual

Brand: BMW

Model: 84 64 0 026 614

Type: Installation Instructions Manual

This manual is also suitable for

84 64 0 025 810

BMW 84 64 0 026 614

This retrofit kit enables the installation of a Nokia hands-free facility in your BMW 7 Series (E38) LHD, enhancing your in-car communication experience.

Download PDF

report

BMW 84 64 0 026 614 Installation Instructions Manual

This manual is also suitable for

BMW 84 64 0 026 614 Installation Instructions Manual

Related papers

Other documents