Eneo DOME-S1 Installation guide

Eneo
Brand
Eneo
Model
DOME-S1
Category
Camera mounting accessories
Type
Installation guide
DOME-S1 Installation Guide
Parts supplied
• DOME-S1
• Installation Guide
• L-Wrench 3 mm
• Sunshild screw with washer M2.5x8 (x3)
• Assembly screw M4x12 (x3)
• Assembly ring
How to assemble
After installing a vandalproof dome camera on the wall, assemble the sunshield with the camera unit as illustrated.
1. Remove the assembly screws from the Dome Cover and adjust viewing angle by the Gimbal.
Gimbal should be set between 40° ~ 60° so as not to get IR LEDs covered by Sunshield. (Built-in 30pcs IR LED model :
35°~60°) If IR LEDs are covered by Sunshield, it causes IR LEDs reection and shown on the video when IR LEDs are ON
at night.
2. Assemble the Dome Cover by using supplied M4x12 assembly screw.
Do not use the screw which was originally assembled with Dome cover. It doesn’t t to Sunshield.
3. Fix the Sunshield by using supplied M2.5x8 screws to M4x12 screws.
4. Since the camera is installed on the wall, please reverse the direction of video left/right and up/down by MIRROR/FLIP
in camera menu.
i
Notice: Please do not use an electronic screw driver to assemble screws.
i
Caution:
Please do not cover IR LEDs by sunshield. It causes IR reection when IR LEDs ON and reection shows on the video. Please
follow application guide with green hook. If IR LEDs are not necessary, please turn them o in the camera.
Limit the gimbal tilt adjustment
60°
40°
M2.5x8
M4x12
VIDEOR E. Hartig GmbH
Carl-Zeiss-Straße 8
63322 Rödermark/Germany
Tel. +49 (0) 6074 / 888-0
Fax +49 (0) 6074 / 888-100
www.videor.com
www.eneo-security.com
Technical changes reserved
© Copyright by VIDEOR E. Hartig GmbH
Version 08/2017
Installation
• Mounting a sunshield may restrict the ability to adjust pan/tilt cam-
era’s view. Before installing the camera unit on the wall, check the
camera viewing direction.
• Place the hole at the top of the sunshield upward so that the
direction of the camera lens is aligned. Do not cover LEDs by the
sunshield.
• The reference points (Sunshield upper hole, Dome cover holes, and
Cable out hole of vandal dome) in alignment is the most eective to
mount the sunshield.
Application with DOME/BASIS1
Application with AK-5
Application with DOME/WEDGE2
Sunshield upper hole
DOME-S1
Camera lens direction
Sunshield upper hole
Cable out hole
Camera lens direction
Sunshield upper hole
Cable out hole
Camera lens direction
Sunshield upper hole
Cable out hole
Camera lens direction
Recom-
mended
installation
Available to
install. However
sunshield is less
eective
Not Recommended .
IR LEDs are covered by
sunshield and it causes IR
reection when LEDs ON.
Installation OK when LEDs
are not used and OFF.
Recom-
mended
installation
Available to
install. However
sunshield is less
eective
Not Recommended.
IR LEDs are covered by
sunshield and it causes IR
reection when LEDs ON.
Installation OK when LEDs
are not used and OFF.
Recom-
mended
installation
Available to
install. However
sunshield is less
eective
Not Recommended .
IR LEDs are covered by
sunshield and it causes IR
reection when LEDs ON.
Installation OK when LEDs
are not used and OFF.
  • Page 1 1
  • Page 2 2

Eneo DOME-S1 Installation guide

Eneo
Brand
Eneo
Model
DOME-S1
Category
Camera mounting accessories
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents