2. Home
  3. Home security & automation
  4. Security cameras
  5. Vitek
  6. VTC-CB4MZ39
VTC-CB4MZ39

Vitek VTC-CB4MZ39, VTC-IR4MZ39, VTD-VD4MZ39 User manual

  • Hello! I am an AI chatbot trained to assist you with the Vitek VTC-CB4MZ39 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
FEATURES:
• 1/2.9” 6.64 MegaPixel Sony STARVIS® CMOS Sensor
• 4 MegaPixel Coax Based Camera (2560x1440px @ 30/25fps)
• Outstanding Low Light Performance with Sony STARVIS® Sensor
• 1500’ HD-Analog Transmission Distance over Coax (Depending on Cable Characteristics
and Integrity)
• Premium 4MP Multi-format Video Output, Digital: EX-SDI 1.0/ 2.0/ 2.1 (4MP/2MP/1.3MP),
HD-SDI (2MP/1.3MP) HD-Analog: TVI Mode (4MP/2MP/1.3MP), AHD Mode (4MP/2MP),
CVBS Test Monitor Out
• F= 3.2~9mm Motorized Zoom Lens with Auto Focus
• Automatically Removable IR Cut Filter by Dual Filter Switch
• True WDR (Wide Dynamic Range) @30/25fps
• 120dB Dynamic Range with DOL(Digital OverLap) WDR @30/25fps
• ROI (Region of Interest) WDR @30/25fps
• Improved Noise Reduction with XD-NR
• DIS (Digital Image Stabilization) Function
• POI Zoom (Point Of Interest), Smart Motion Zoom, Preset Zoom, Home Position
• Privacy Mask, Defog, Sens-up(~x32), D-WDR, BLC/HLC, Mirror/Flip, Flickerless, Brightness,
Smart IR, Lens Initialize, Title Set, Color D/N
• High performance at Low Light Sensitivity (Sens-up On)
• Variety of Resolution : 1440p/1080p/720p Without Loss of FOV (Field of View)
• OSD Menu for Easy Installation and Maintenance
• Circuit Protection Protects Against Faulty Connection in Power Polarity
• Isolated Power Supply Protects Against Ground Loop Problem
• COC Control through HD-TVI (Pelco-C®) or AHD
• IP68 (VTD-VD4MZ39, VTC-IR4MZ39), IK10 (VTD-VD4MZ39)
• 12VDC, 24VAC Operation
VIRTUOSO HI DEFINITION
OVER COAX CAMERAS
Premium 4 Megapixel Indoor/Outdoor
6-in-1 HD/EX-SDI / TVI / AHD / CVI /
CVBS Motorized Varifocal Cameras
COAX
VTC-CB4MZ39
VTC-IR4MZ39
VTD-VD4MZ39
VITEK
VITEK
Table of Contents
Safety Precautions.............................................. 3-4
Overview: VTC-CB4MX39............................... 5-7
Overview: VTD-VD4MZ39............................... 8-15
Overview: VTC-IR4MZ39................................. 16-20
Connections: VTD-VD4MZ39, VTC-IRMZ39... 21
OPERATING INSTRUCTIONS.................... 22-38
OSD Menu.......................................... 22-24
Zoom / Focus..................................... 24-26
Exposure.............................................. 27-28
WDR.................................................... 29-30
XD-DNR............................................. 31
Day / Night.......................................... 31-33
Picture Adjustment............................ 33-35
Special Functions.............................. 35-37
System.................................................. 37-38
Detailed Specifications.................................... 39-41
Accessories........................................................ 43
Warranty Information........................................ 44
2 3
Safety Precautions
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To prevent electric shocks and risk of fire hazards, do NOT use other than with
a specific power source.
The symbol is intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Caution :
Any changes or modifications in the construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Mains power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power mains interruptions, it is
recommended that the model be powered from an uninterruptible power supply
(UPS) or a battery.
3
Safety Precautions
NOTICE
The images used in this instruction manual are processed to help comprehension
and may differ from actual video of the camera.
Avoid installing areas where has shock or vibration which results in the problems.
Pay attention to safety when laying the connection cable and observe that the cable
is not subjected to heavy loads, kinks or damage and no moisture can get in.
The warranty becomes void if repairs are undertaken by unauthorized persons.
Maintenance and repair have to be carried out only by authorized service centers.
Use only a mild detergent to clean the housing.
The camera should never be operated beyond the technical specifications.
This can lead to destruction.
The camera should never be operated in water.
Limited Product Warranty
VITEK products carry a three (3) year limited warranty. VITEK warrants to
the purchaser that products manufactured by VITEK are free of any rightful
claim of infringement or the like, and when used in the manner intended,
will be free of defects in materials and workmanship for a period of three
(3) years, or as otherwise stated above, from the date of purchase by the
end user. This warranty is nontransferable and extends only to the original
buyer or end user customer of a VITEK Authorized Reseller.
The product must have been used only for its intended purpose, and not
been subjected to damage by misuse, willful or accidental damage, caused
by excessive voltage or lightning.
The product must not have been tampered with in any way or the
guarantee will be considered null and void.
This guarantee does not affect your statutory rights.
Contact your local VITEK Reseller should servicing become necessary.
VITEK makes no warranty or guarantee whatsoever with respect to
products sold or purchased through unauthorized sales channels. Warranty
support is available only if product is purchased through a VITEK
Authorized Reseller.
4 5
Composition - VTC-CB4MX39
Dimensions
Operating InstructionsCamera
unit : inches (mm)
4.45 (113)
Ø2.13 (54)
4.92 (125)
2.84 (72)
2.99 (76)
5
Part Names - VTC-CB4MX39
REAR VIEW
• Extreme care should be taken NOT to scratch the window in front of the lens.
• Care should be taken so the cable is NOT damaged, kinked or exposed
to hazardous areas.
• Do not expose the camera directly to a strong light source such as the sun
or spotlights.
CAUTION
OSD Control Joy stick
Power input terminal
(AC24V/DC12V)
RS-485 / IR connector
Video format selection Switch
HD-Analog output connector
Power LED
HD-SDI/EX-SDI output connector
EX-SDIHD-SDI
HD-ANALOG
CONTROL
POWER
Front Case
Window
Rear Case
Mount Holes
(Top / Bottom)
6 7
Installation Instructions - VTC-CB4MX39
Power Supply Connections
Using OSD Controller
The Camera can work with either AC24V or DC12V, dual voltage power.
Primary and secondary grounds are completely isolated to avoid a
possible ground-loop problem.
1) SET ( ) : Access to the menu or enter the setting.
To enter the main menu, press the Set Key down.
2) UP/DOWN ( ) : Choose the desired sub-menu and move the
cursor up or down.
3) LEFT/RIGHT (
: Set up the value of the selected menu. Used to
adjust the desired menu selection and to move the cursor left or right.
Description of the OSD control operation
4) ‘denotes pressing straight down for 2 seconds
Setup menu can be accessed and controlled by OSD control joystick
on the rear of the camera unit. Five commands are available
with the joystick.
i
HD-SDI or EX-SDI is selectable by Video format switch only.
TVI mode or AHD mode is selectable in the menu only.
(SYSTEM> ANALOG MODE)
OSD Control Joy Stick
Video format Switch
EX-SDIHD-SDI
HD-ANALOG
CONTROL
POWER
Description of the Auto Focus Zoom, Motorized ZOOM&FOCUS adjustment
1) : Zoom In
2)
3) : Focus Near
4)
(*) Works only when OSD Menu is inactive.
7
Composition - VTD-VD4MZ39
Torque Wrench:
.12” (3mm) (1pc)
Plastic Anchor:
.24 x 1.18” (6 x 30mm) (4pcs)
Mounting Screw:
.16 x 1.18” (4 x 30mm) (4pcs)
Dome Camera
Connector fixing Screw:
.1” x .24” (2.6 x 6mm) (1pc)
Mounting
Template
Operating
Instructions
Video Sub-out
Cable (1pc)
Assembly Screw:
.16 x .55” (4 x 14mm) (3pcs)
Dome Camera
Surface mount
Conduit Spacer &
Conduit hole cap(1set)
8 9
Dimensions - VTD-VD4MZ39
Ø5.51 (140)
Ø3.93 (100)
4.69 (119)
Ø4.02 (102)
Ø5.51 (140)
2.64 (67)
4.69 (119)
1.46 (37)
3.23 (82)
[ Flush mount ] [ Surface mount ]
PCD Ø4.72 (120)
3-Ø.17 (4.2)
unit : inches (mm)
9
SURFACE MOUNT
Part Names - VTD-VD4MZ39
BUBBLE DOME
3-AXIS GIMBAL
DOME COVER
SAFTY WIRE
FLUSH MOUNT
LENS
POWER CABLE
VIDEO OUTPUT
[ BOTTOM VIEW ]
POWER SUPPLY
CONNECTOR
POWER
CABLE
OSD Menu Control board
10 11
Installation Instructions - VTD-VD4MZ39
1. Locate the mounting template at the installation position and drill the ceiling or
wall if needed.
2. Open the dome cover by loosening screws (.16 x .47” / 4 x 12mm).
Use the torque wrench supplied.
4. Set the camera’s viewing angle and focus.
5. Put the dome cover on the dome base unit and tighten the assembly screws.
- Place the dome base unit on pre-drilled position and attach it through using
mounting screws (16 x 1.18” / 4 x 30mm).
- Route the Power & Ethernet cable to the connecting place.
- Place the surface mount on a pre-drilled position and attach it through using
mounting screws(.16 x 1.18” / 4 x 30mm). Assemble the cable pipe,
otherwise tighten a pipe hole cap with PM screw (
.1 x .24” / 2.6 x 6mm).
- Route the Power & Ethernet cable to the connecting place.
- Affix the dome base unit to the surface mount using the assembly screws
(.16 x .55” / 4 x 14mm). Before securing the dome base make sure the assembly
holes are aligned with the surface mount assembly holes.
A. Flush mount type:
B. Surface
mount type:
Assembly Screw
Torque Wrench
Assembly Screw
Mounting Screw
A
Flush mount type
B
Surface mount type
(.16 x .55” / 4 x 14mm)
(.16 x .47” / 4 x 12mm)
(16 x 1.18” / 4 x 30mm)
11
Installation Instructions - VTD-VD4MZ39
• Pole mount
adaptor
• Tilted mount
• Wall mount
• Tilted junction
mount
• In the case of installation with Flush / Surface / Tilted mount, IP protection
rating is not guaranteed.
• If power or Video connectors are exposed to water or rain, a sunshield is
necessary.
• Extreme care should be taken NOT to scratch the bubble dome surface while
installing or adjusting the camera.
• Care should be taken so the cable is NOT damaged, kinked or exposed in
to hazardous areas.
• Tighten the dome cover fixing screws so that there is NO gap
between the Lens hood and clear bubble to avoid light inflow from IR LEDs.
CAUTION
CAUTION
• Wall mount
Sunshield
12 13
Installation Instructions - VTD-VD4MZ39
Option 2.
Installation with Surface mount / Tilted mount
Option 1.
Installation with Flush mount / Tilted Junction mount
3
1
Cable Holder
Video Output
Cables
2
Cable is unattached to the Dome base.
Connect the power cable to their repective connections.
Cable is unattached to the Dome base.
Tie up the VIDEO OUTPUT cables with cable holder.
Tie up the POWER SUPPLY cable with cable holder as illustrated.
Connect the wiring connector to their repective connections.
Cable Holder
Power Supply
13
Installation Instructions - VTD-VD4MZ39
• Extreme care should be taken NOT to scratch the bubble dome surface while
installing or adjusting the camera.
• Care should be taken so the cable is NOT damaged, kinked or exposed to
to hazardous areas.
• Tighten the dome cover fixing screws so that there is NO gap
between the Lens hood and clear bubble to avoid light inflow from IR LEDs.
CAUTION
Limit of pan & tilt
1) Pan limit:
Pan is limited to +/- 173°.
Do NOT force the gimbal over the limit to prevent internal damage.
2) Tilt limit:
Tilt is limited to 25° min ~ 90° max. with reference to the ceiling when the
rotation of camera module is 0°, that is, the image is aligned horizontally.
3) Rotation limit (Horizontal image alignment):
Rotation is limited to +/-95° max.
25º
90º
ROTATION
+/- 95°
PAN
+/- 173°
TILT
25°~90°
*** POWER SUPPLY INSTALLATION INSTRUCTIONS CONTINUED ON PG 21
14 15
Operating Instructions - VTD-VD4MZ39
Using OSD Control Controller
The setup menu can be accessed and controlled by the OSD control joy stick
inside the camera unit. Five commands are available with the joy stick.
The design of OSD may differ according to the Model.
1) SET (
) : Access to the menu or enter the setting.
To enter the main menu, press the Set Key down.
2) UP/DOWN ( ) : Choose the desired sub-menu and move the
cursor up or down.
3) LEFT/RIGHT ( : Set up the value of the selected menu. Used to
adjust the desired menu selection and to move the cursor left or right.
Description of the OSD control operation
4) ‘denotes pressing straight down for 2 seconds
Description of the Motorized ZOOM&FOCUS* adjustment
1) : Zoom In
2)
3) : Focus Near
4)
(*) Works only when OSD Menu is inactive.
OSD Control
Joy Stick
Video sub-out Connector
Video Format
DIP Switch
EX-SDI HD-SDI: The default setting is HD-SDI mode.
Using Video format DIP switch
15
Composition - VTC-IR4MZ39
Dimensions
unit : inches (mm)
Video Sub-out
Cable (1pc)
Mounting
Template
Operating
Instruction
Camera
Easy
Bracket
Plastic Anchor:
.24 x 1.18” (6 x 30mm) (4pcs)
L
4.35 (110.5)
3.53 (89.60)
4.37 (111)
3.94 (100)
3.31 (84)
3.39 (86)
3.15 (80)
10.11 (256.70)
Torque Wrench:
.12” (3mm) (1pc)
Mounting Screw:
.16 x 1.18” (4 x 30mm) (4pcs)
Assembly Screw:
.16 x .55” (4 x 14mm) (3pcs)
16 17
Part Names - VTC-IR4MZ39
Adjustment of viewing angle with a bracket
• Extreme care should be taken NOT to
scratch the window in front of lens.
• Care should be taken so the cable is NOT
damaged, kinked or exposed to
hazardous areas.
• Do not expose the camera directly to
a strong light source such as the sun
or spotlights.
CAUTION
Power & video cable
through the rear mount
and connect to the
proper source
Sunshield
Sunshield Bolt
Easy
Bracket
OSD Setup
Control Cover
Bracket
Lock/Unlock
Screw
Torque
wrench
Lock/Unlock
Screw
17
Installation Instructions - VTC-IR4MZ39
1. Locate the mounting template at the installation position and drill the ceiling or
wall if needed. ( *The easy bracket can not be installed on the ceiling)
2. Place the easy bracket on pre-drilled position and attach it through using mounting
screws (
.16 x 1.18” / 4 x 30mm) . Skip this step when an easy bracket is not installed.
3. Route the Power cable to the connecting place.
Hook up the camera bracket with the easy bracket as illustrated below.
4. Attach the camera bracket through using assembly screws (.16 x .59” / 4x15mm).
5. Set the camera’s viewing angle.
6. Put the sunshield on the camera unit and tighten the sunshield-bolts.
Mounting Screw
:
.16 x 1.18” (4 x 30mm)
Plastic Anchor
:
.24 x 1.18” (6 x 30mm)
1
2
Torque Wrench
REAR VIEW
3
Cable exit
4
Assembly Screw
:
.16 x .55” (4 x 14mm)
18 19
Installation Instructions - VTC-IR4MZ39
Pan & Tilt adjustments
1) Pan limit:
Pan is limited to +/- 90°.
3) Inclination limit
(Horizontal image alignment):
Inclination limited to +/-90° max.
2) Tilt limit:
Tilt is limited to 0°(2°) min ~ 90° max.
for wall(ceiling) installation respectively
with reference to the wall(ceiling) when
the inclination of camera module is 0°,
that is, the image is aligned horizontally.
90° 90°
• Unlock the screw on the camera bracket using the torque wrench supplied
• Set the camera’s viewing angle then lock the screw on the bracket.
88°90°
±90°
• on the ceiling • on the wall
19
Operating Instructions - VTC-IR4MZ39
Setup menu can be accessed and controlled by OSD control joystick on
the side of camera unit. Five commands are available with the joystick.
The design of OSD could differ depending on the model.
Description of joystick operation
2) UP/DOWN ( ) : Choose the desired sub-menu and move the cursor up or down.
3) LEFT/RIGHT ( : Set up the value of the selected menu.
Used to adjust the desired menu selection and to move the cursor left or right.
Using OSD controller
4) ‘denotes pressing straight down for 2 seconds
Video Sub-out
Connector
OSD Control Joy Stick
SUB-OUT
ZOOM
Cover Open
Description of the Motorized ZOOM&FOCUS* adjustment
1)
: Zoom In
2)
3) : Focus Near
4)
(*) Works only when OSD Menu is inactive.
ANALOG OUT should be set to TVI MODE, AHD MODE or CVI MODE
to get CVBS video in sub-out. If it is set to CVBS, there is no CVBS video
in sub-out port. (SYSTEM> OUTPUT> ANALOG OUTPUT)
If CVBS video is enabled through ANALOG OUT or Sub-out port, WDR
and 3D-NR functions are disabled in all video outputs.
This should be considered when installer adjusts the video with installation
monitor via CVBS video signal.
20 21
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/