Akura ASDVCR210RS User manual

Type
User manual
1
ASDVCR210R-S
TV/VCR/DVD COMBINATION
Users Manual
2
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR
BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The graphic symbols on the back cover of the set mean the following:
The lightning flash with arrowhead symbol within an equilateral triangle is intended to
alert the user to the presence of uninsulated "dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
NSTALLATION
LOCATE the receiver in the room where direct light does not strike the screen. Total darkness or
a reflection on the picture screen can cause eyestrain. Soft and indirect lighting is recommended
for comfortable viewing.
ALLOW enough space between the receiver and the wall to permit good ventilation. Should the
set be boxed in, allow at least 15cm ( 3 ) around all surfaces to provide sufficient ventilation.
AVOID excessive warm locations to prevent possible damage to the cabinet or component failure.
CONNECTION
This TV receiver can be connected to AC: 230V~ 50Hz .
AUTOMATIC DEGAUSSING
All color television receivers are sensitive to magnetic influences, usually caused by either mov-
ing the receiver from one place to another or using certain electrical appliances near the receiver.
This residual magnetism as it is called, sometimes causes distortion which gives rise to "blotchy"
areas of color in the picture. To avoid these effects the receiver incorporates an automatic
degaussing circuit which operates for a short while immediately each time the receiver is switched
on using the mains switch. This circuit removes any residual magnetism in the metal parts of the
picture tube, and ensures that each time the set is switched on, the pictures are lifelike.
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EX-
POSE THIS APPLIANCE TO RAIN OR MOISTURE.
3
CAUTION
Never tamper with any components inside your set, or any other adjustment controls not men-
tioned in this manual. All television receivers are high voltage instruments. Your Picture Tube is
highly evacuated. If it is broken, glass fragments will be expelled at a high velocity. Scratching,
Chipping or undue pressure must be avoided. When cleaning the set, it is wise to disconnect
from the mains supply. Use a soft dry cloth to clean the screen. Non-abrasive cleaning products
may be used should the glass become coated with smoke residue. Should your set become
Faulty. Do NOT attempt to repair. Call an Authorized Service Engineer.
LEAVING THE SET UNATTENDED
Should the user leave the set unattended for long periods, such as holidays. It is advised you
unplug the set from the Mains Supply, and if used, external aerial.
DANGER
Invisible laser radiation when open
and interlock failed or defeated. avoid
direct exposure to laser beam.
laser safety
This unit employs an optical laser beam system in the CD
mechanism,designed with built in safeguards. Do not attempt
to disassemble, refer to qualified service personnel.
Exposure to this invisible laser light light beam may be harmful
to the human eye.
THIS IS A CLASS-1 LASER PRODUCT. USE OF CONTROLS,
OR ADJUSTMENTS OR PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN, MAY RESULT IN HAZARDOUS
LASER LIGHT BEAM EXPOSURE.
4
IMPORTANT SAFEGUARDS
PREFITTED MAINS PLUGS
For you convenience a mains plug has been fitted to this appliance. For your safety please ob-
serve the following information.
1. Should the fuse in the plug fail, remove the plug from the wall socket and replace the fuse with
a 3 Amp ASTA approved to BS 1362 fuse.
2. Should the mains plug become detached, rewire in accordance with the diagram below.
3. If the mains plug is out off the cable, rewire the replacement plug in accordance with instruc-
tion give in this manual.
4. CAUTION: Under no circumstances should the discarded plug be inserted into the mains
socket. To prevent a shock hazard carefully dispose of the discarded plug.
Do not leave the plug lying around where children might see it.
CAUTION:
DANGEROUS VOLTAGES EXIST INSIDE THIS UNIT DO NOT REMOVE COVER
(OR BACK).
NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SER-
VICE PERSONNEL. DISCONNECT FROM MAINS SUPPLY WHEN NOT IN USE.
This wires in this mains lead are coloured in accor-
dance with the following wiring codes:
Blue................................... Neutral
Brown................................... Live
This wires in this mains lead must be connected to
the terminals in the plug as follows:
Blue Wire........................... N or Black
Brown Wire.......................... L or Red
Only a 3 Amp fuse should be fitted in the plug or a 5 Amp fuse at the distribution board.
WARNING: UNDER NO CIRCUMSTANCES MUST THE LIVE OR NEUTRAL WIRES BE
CONNECTED TO THE EARTH TERMINAL IN A 3 - PIN MAINS PLUG.
This symbol means that this unit is double insulated. An earth connection is not required.
5
l DVD, VCD, CD, CD-R(MP3), CD-RW, VHS playback function
l DVD one-touch record function
l Watching DVD for recording broadcast
l Integrated REMOTE (VCR, DVD)
l Index Search
l GUI (Graphical User Interface) OSD (On Screen Display)
By using the [DISPLAY] button on the remote control, information on the DVD / VCD / CD
player and disc, can be displayed on the TV screen.
l Screen saver function (DVD)
l Built-in Dolby Digital decoder (DVD)
l Composite Scart video out
l Slow Forward / Reverse playback (DVD)
l Fast Forward / Reverse playback (DVD)
l Search of title, chapter, and time in DVD disc, and search of time and track time in CD
l Various TV aspect (DVD) 4:3 for Pan and Scan, 4:3 for Letter Box, and 16:9 for Wide
l Repeat playback for DVD
l 4 languages OSD (On Screen Display) function (DVD)
You can select and display OSD in 4 languages.
l Parental Lock function (DVD)
This function can prevent playback of software that may be unsuitable for children.
l Multi Audio function (DVD)
The audio soundtrack can be heard in up to 8 languages. it depends on the disc. (The number
of audio languages depends on the software.)
l Multi Subtitle function (DVD)
The subtitle can be seen in up to 32 languages. it depends on the disc. (The number of
subtitle languages depends on the software.)
l Multi Angle function (DVD)
This function allows you to choose the viewing angle of scenes which were shot from a
number of different angles. (The number of angles depends on the software.)
l Screen zoom function (DVD)
Please read carefully before using this product.
Installation and handling
l It is wise not to place this set near strong magnetic fields, such as large speakers. This may
affect the screen purity and video recordings.
l Do not spill or use a cleaning fluid, or volatile chemicals, such as petrol. This could damage
the plastic case or paint finish.
FEATURES OF THIS PRODUCT
6
Not in use
l If the unit is not to be used for long periods, it is wise to remove tapes and discs.
l Disconnect the mains power and the external aerial, if fitted.
l Remove the batteries from the Remote control to prevent battery I eakage.
l Occasionally plug the set in and test it. This will keep the components in good condition.
Moving
l Should you need to move the set, it is best to use the original packing. If this is not available,
wrap the set in soft material. This helps prevent damp getting into the set causing condensation.
Cleaning
l Dust will naturally settle on this appliance. Clean with a soft cloth.
l If the dirt is greasy, use a damp soft cloth with a mild detergent solution.
l Do not use solvent cleaners such as Petrol or Benzines. This will damage the cabinet.
Maintainance
l The Video and DVD sections are precision instruments which need periodical maintenance. If
the picture deteriorates from either playback system, try a proprietary tape head or laser
cleaner. If this is not successful consult your local repair dealer.
External aerial maintainance
l Should you use an external aerial and the picture deteriorates. This may be due to the aerial
being moved or damaged in high winds. Consult your local dealer for advice.
Copyright material
l Copyright material is only for personal use. It is IIIegal to copy copyright material from DVD to
tape, unless for personal use.
Tape and disc handling
l Do not use tapes or discs if they have been contaminated with:
- Fungus or mold, Juice or Dust.
l Do not use tapes or discs if they have been damaged, scratched or tapes that have been
rejoined after breaking.
l Tapes and discs should be stored vertically in a dry dust free location. Avoid high humidity or
high temperatures. Do not store tapes near Loudspeakers.
7
Overview of the equipment
1.VCR Eject
Press to stop tape movement and Eject
tapes.
2.Video in/Audio in(L/R)
VCR External video and audio inputs.
3.Standby switch
Press to turn the power on and off.
NOTE:
The power switch will not operate during
OTR and Record modes.
4.Power indicator
In standby mode the LED will illuminate.
5.Function(TV+VCR/DVD)
Select the TV+VCR or DVD source.
6.Channel up/down
Press to change the channel .
7.Cassette compartment
Insert a video cassette into this slot.
8.Volume control
To adjust the sound output level.
9.Record/OTR
Press to record the programme currently
shown on the screen. Press multiple times
to process OTR time options.
10.Record indicator
When recording is in progress this LED
will light.
11.Timer indicator
When a TIMER recording is set, the LED
will light.
12.Screen off indicator
When screen is off the LED will illuminate.
13. Remote sensor
This receives a signal from your Remote
control.
14.Pause/Step
Press to Pause the picture, press again to
advance the picture in Step mode.
15. Play(VCR/DVD)
Press to start either DVD or Tape playback.
16. DVD tray
Open or close tray by pushing DVD open/
close button,place a disc on the disc tray.
label side up.
17.REW(VCR/DVD)
press ( )button to rewind the disc or VCR
tape.
18. FF(VCR/DVD)
Press( )button to fast forward the DISC
or VCR tape.
19. Stop (DVD)
Stop playing the disc.
20. Open/Close(DVD)
Use to open or close the tray.
8
Overview of the equipment,continued
Back panel
1. Main Power Switch
2. DVD Digital Audio Output (Coaxial)
3. Euro AV2 / DECODER
4. Euro AV1
5. TV Antenna In
9
Overview of the equipment,continued
Remote control
1. Open/close Button(DVD) Eject/(VCR)
2. Display Button
3. +10 Button
4. Numeric Buttons(TRACKING)
5. SP/LP Button
6. Channel / Direction Buttons( Up Down
Left Right )
7. Setup Button
8. Play Button
9. Stop Button
10. Fast Forward Button
11. Fast Backward Button
12. Slow REW Button
13. Return Button
14. Zoom Button
15. PBC Button
16. Angle Button
17. Subtitle Button
18. Audio Button
19. Screen ON/OFF Button
20.PP button(personal preference)
21. Standby Button
NOTE: The power switch will not function during OTR
and Record mode.
22. TV/AV Button
23. MUTE Button
24. Volume (- ) Button
25. Volume (+) Button
26. DVD Menu Button
27. Enter Button
28. REC Button
29. Pause/STEP Button
30. Previous Button
31. Next Button
32. Slow F.F Button
33. Clear Button
34. Program Button
35. Repeat Button
36. Repeat A-B Button
37. Search Button
38. Digest Button
39. TV+VCR/DVD Select Button
40.
Menu Direction Button(Up ,Down ,Left ,Right )
41. Menu Button
l Objects between the
remote control and VCR
will block the path of the
remote control beam.
l Dark walls,direct
sunshine or very bright
light will reduce the
remote sensors sensitivity.
l The remote control will not
work correctly if you press
several buttons at the
same time.
10
Setting up your unit
1. Once you have connected your unit and put batteries in the remote control, you must
do the following :-
l Connect the TV aerial located at the back.
l Press the Power switch to ON. (Located at the back)
l Press the standby button on the handset or front panel. The screen should light after a few
seconds.
2. BASIC OPERATION
(1) Press the [SETUP] button to display the SETUP menu on the screen.
(2) Press the [ / ] buttons to select the desired function on the SETUP menu.
And press the [ENTER] button to confirm the selected function.
(3) Press the [SETUP] button to return to the SETUP menu at any time.
(4) Press the [SETUP] button to leave the SETUP menu screen.
3. MANUAL CLOCK SET
l Press the [SETUP] button to call the Main SETUP.
l Press the [ / ] buttons to select the line of Clock Set and press the [ENTER] button to
confirm that.
l To set the clock for the first time, use the [0-9] buttons, in the following order:
Hours->Minutes->Day->Month->Year.
l To correct settings, move the cursor with the [ / ] to the correct location and input the new
numbers.
l The clock will work, although the VCR is in the clock setting state.
l To set the “Year, use only the last two digits, i.e. 2001 = 01.
l Press the [ Enter ] button to confirm the clock settings. After storing, the menu reverts to the
Setup menu. The settings being also stored in the VCR setup memory. If the Clock settings
are interrupted before completion then the VCR timer will not operate.
4. DISPLAY COLORS
All lines have a Grey background. Selected lines have a Green background with White
characters.
11
Setting up your unit, continued
----------------->
SETUP
Clock set
Record timer
Installation
Search
Preferences
ENTER:Confirm SETUP:End
CLOCK SET
SETUP:End
Time --:--
Date -- / -- / ----
CLOCK SET
SETUP:End
Time 11:--
Date -- / -- / ----
CLOCK SET
SETUP:End
Time 11:11
Date -- / -- / ----
CLOCK SET
SETUP:End
Time 11:11
Date -- / -- / ----
CLOCK SET
SETUP:End
Time 11:11
Date -- / -- / ----
----------------->
--->
--->
-------->
------>
CLOCK SET
ENTER:Confirm SETUP:End
Time 11:11
Date -- / -- / ----(Fri)
12
RECORD TIMER
1. TIMER REVIEW (Erasure & Correction)
1-1.ERASURE
(1) Press the [SETUP] button to call the SETUP menu in TV state or press the [PROGRAM]
button.
Press the [ / ] buttons to select the line of Record Timerand press the [ENTER] button to
confirm that.
(2) At that time, the VCR will check whether there are some errors or not:
- If the clock has not been set, then it will change to Clock Setscreen automatically.
- If the PRs have not been set, then it will change to Installationscreen automatically.
If there is no error, (2) screen appears.
Press the [ / ] buttons to select a erasing timer program.
The [ENTER] button is pressed to confirm that, the stored contents of the selected Timer program
are displayed.
(3) The [CLEAR] button is pressed to erase.
1-2.CORRECTION
(1) Press the [SETUP] button to call the SETUP menu in TV state or press the [PROGRAM]
button.
Press the [ / ] buttons to select the line of Record Timerand press the [ENTER] button to
confirm that.
SETUP
Clock set
Record timer
Installation
Search
Preferences
ENTER:Confirm SETUP:End
13
(2) At that time, the VCR will check whether there are some errors or not:
- If the clock has not been set, it will change to Clock Set screen automatically.
- If the PRs have not been set, it will change to Installation screen automatically.
- If there is no error, (2) screen appears.
Press the [ / ] buttons to select a correcting record timer program.m.
The [ENTER] button is pressed to confirm that, the stored contents of selected Record Timer
program are displayed on the TV screen.
(3) The [ / ] buttons are pressed to correct the record timer program, the OSD screen will be
changed to the screen of (3).
(4) How to correct: See the NEW PROGRAMMING procedures. The next steps are same as the
steps of New Programming.
(5) To correct the other record timer programs, repeat the procedure from the step (1) to step (4).
(6) When the programme setting has been achieved, turn off the unit by pressing the Standby”
button. The Timerindicator will light, and when the programmed time is reached the recording
will start automatically.
Setting up your unit, continued
(1)
SETUP
Clock set
Record timer
Installation
Search
Preferences
ENTER:Confirm SETUP:End
SETUP
Clock set
Record timer
Installation
Search
Preferences
ENTER:Confirm SETUP:End
-->(1) GO TO Clock set”
-->(2) GO TO Installation”
(2)
(3)
ENTER
PR Start End Date
01 14:10 16:00 19/11
11 10:00 12:00 24/12
AV 12:00 14:00 25/12
04 10:10 11:30 Mo-Fri
06 11:40 12:00 W/Fri
07 15:00 17:00 Mo-Sa
08 18:00 19:00 Mo-Su
ENTER:Confirm SETUP:End
------>
---->
------>
TIMER 2
PR 01
Starttime 14:10
Endtime 16:00
Startdate
18/11(Wed)
Howoften Once
Tapespeed SP
ENTER:Confirm SETUP:End
14
2. NEW PROGRAMMING
2-1.MENU OPERATIONS
(1) Press the [SETUP] button to call the Setup Menu .
Press the [ / ] buttons to select the line of Record Timerand press the [ENTER] button
to confirm that.
(2) At that time, the VCR will check whether there are some errors or not:
- If the clock has not been set, then it will change to Clock Setscreen automatically.
- If the PRs have not been set, then it will change to Installationscreen automatically.
If there is no error, (2) screen appears.
Press the [ / ] buttons to select the empty(not occupied) record timer program.
Press the [ENTER] button to confirm that.
(3) Press the [ / ] buttons to select the type of the wanted timer recording.
The [ENTER] button is pressed to confirm that, the data input screen for the new timer
programming will appear.
* ONCE (In the case of selecting the type to Once”)
(4) Press the [0-9] buttons to set a PR number or press the [ / ] buttons to select an external
(AV).
PRs: To choice the recording signals from the own tuner, which is built-in VCR to tune and
detect broadcasting signals.
(5) Press the [0-9] buttons in the following order: start time -> end time -> start date.
In initial state, the start date will be displayed a current date automatically.
Also, if the day or the month is changed at the start date, the day of the week will be changed
too automatically, changed after inputting the day.
Press the [ / ] buttons to select the tape speed and press the [ / ] button to input the
next data.
In case of SP only model, this speed selection guide wont appear on the screen.
Press the [ENTER] button at the screen to confirm that.
If the program overlaps with another one, which had already been programmed, the Error
message will appear for 3 seconds and it will change to the screen for the TIMER REVIEW”
automatically.
If the program does not overlap, the Guide Message will appear for 3 seconds.
* DAILY(MON-FRI) [In the case of selecting the type to DAILY(MON-FRI)”]
All the procedures of daily (Mon-Fri) recording are the same as once timer recording”.
* DAILY(MON-SAT) [In the case of selecting the type to DAILY(MON-SAT)”]
All the procedures of daily (Mon-Sat) recording are the same as once timer recording”.
* DAILY(MON-SUN) [In the case of selecting the type to DAILY(MON-SUN)”]
All the procedures of daily (Mon-Sun) recording are the same as once timer recording”.
* WEEKLY [In the case of selecting the type to WEEKLY”]
All the procedures of daily (once a week) recording are the same as once timer recording.
(6) When the programme setting has been achieved, turn off the unit by pressing the Standby”
button. The Timerindicator will light, and when the programmed time is reached the recording
will start automatically.
Setting up your unit, continued
15
Setting up your unit, continued
* ONCE
TIMER 1
/
: Up/Down SETUP:End
PR -
Starttime 11:10
Endtime 12:00
Startdate
11/11(Wed)
Howoften Once
Tapespeed SP
TIMER 1
ENTER:Confirm SETUP:End
PR 11
Starttime 12:20
Endtime 14:20
Startdate
11/11(Wed)
Howoften Once
Tapespeed SP
TIMER 1
/
: Up/Down SETUP:End
PR 11
Starttime - -: --
Endtime - -:- -
Startdate
11/11(Wed)
Howoften Once
Tapespeed SP
TIMER 1
/
: Up/Down SETUP:End
PR 11
Starttime 12: --
Endtime - -:- -
Startdate
11/11(Wed)
Howoften Once
Tapespeed SP
--> --> -->
(5)
<--
<------------------
------------------->
------------------->
ENTER
TIMER 1
Startdate
11/11(Wed)
Howoften Mon-Fri
Tapespeed SP
TIMER 1
Startdate
11/11(Wed)
Howoften Mon-Sun
Tapespeed SP
TIMER 1
Startdate
11/11(Wed)
Howoften Mon-Sat
Tapespeed SP
TIMER 1
Startdate
11/11(Wed)
Howoften Weekly
Tapespeed SP
* Daily
* Daily
* Daily
16
Setting up your unit, continued
--> ---->
TIMER 1
/
: Up/Down SETUP:End
PR 11
Starttime 12: 20
Endtime - -:- -
Startdate
11/11(Wed)
Howoften Once
Tapespeed SP
TIMER 1
/
: Up/Down SETUP:End
PR 11
Starttime 12: 20
Endtime 14: - -
Startdate
11/11(Wed)
Howoften Once
Tapespeed SP
TIMER 1
ENTER:Confirm SETUP:End
PR 11
Starttime 12:20
Endtime 14:20
Startdate
11/11(Wed)
Howoften Once
Tapespeed SP
TIMER 1
ENTER:Confirm SETUP:End
PR 11
Starttime 12:20
Endtime 14:20
Startdate
11/11(Wed)
Howoften Once
Tapespeed SP
TIMER 1
ENTER:Confirm SETUP:End
PR 11
Starttime 12:20
Endtime 14:20
Startdate
11/11(Wed)
Howoften Once
Tapespeed SP
<-- <- <- <-
<-------------------------------------------------------------------------------------------------------
TIMER 1
PR 11
Starttime 12:20
Endtime 14:20
Startdate
11/11(Wed)
Howoften Once
Tapespeed SP
Overlap!
Timer 1 Stared
--->
--->
17
1. AUTO SEARCH
(1) Press the [SETUP] button to display the Setup Menu screen in TV mode.
Press the [ / ] buttons to select the line of Installationand press the [ENTER] button to
confirm that.
(2) Press the [ / ] buttons to select the line of Auto Installationand press the [ENTER] button
to confirm that.
(3) The searching step is follow
Option:
- PAL I: CH01-13, CH21~CH69, CC01-54 PAL I/I: CH01-13, CH21-CH69, CC01~CC54
If the VCR tunes a station, it will display the virtual station name such as PR01for 1seconds.
During channel searching, you can press the [SETUP] button to interrupt it, then the VCR goes
to the Real Picture.
(4) After the channel searching is completed, the Please waitscreen will appear a while.
(5) If other stations are positioned on or near the current RF OUTPUT PR, the guide message will
appear automatically, even if you are not using RF output, you will still need to complete the
process below.
The VCR recommends the optimal RF OUTPUT PR number automatically. Press the
[Enter] button to confirm. If you wish to select your own PR number press the [0-9] buttons,
and press [Enter] to confirm. If you dont want to change, press the [Setup] button to return
to the main screen.
(6) The Clock Set screen automatically appears for manual clock set.
How to set the clock: See the CLOCK SET procedures.
(7) After completing the Auto Searching procedures, the “Manual Installationscreen appears.
Whenever a channel is searched and memorized, the PR number will be increased from 01 to99 .
During channel searching, you can press the [SETUP] button to interrupt it, then the VCR goes
to the Real Picture.
Setting up your unit, continued
18
2. MANUAL INSTALLATION
(1) Press the [SETUP] button to display the Setup Menu screen in TV state. Press the [ / ]
buttons to select the line of Installationand press the [ENTER] button to confirm that.
(2) Press the [ / ] buttons to select the line of “Manual Installationand press the [ENTER]
button to confirm that.
Press the [ / ] buttons to select the re-searching channel and press the [ENTER] button to
confirm that.
l Reception - The list is: AERIAL, CABLE
If aerial is selected, CH is written before the channel number. If cable is selected, CC is written
before the channel number. If the user changes the reception: AUTO SEARCHis set to --”
l Auto search -The user can either launch the auto search using right and left keys, or directly
enter the channel number. Auto search moves automatically from last cable to first antenna
channel found and vice versa.
The Searching step is follow
- PAL I: CH01-13,CH21-69,CC01-54 PAL I/I : CH01-13,CH21-69, CC01~CC54
l Fine Tuning-The user can fine tuning using right and left keys
l Decoder-It is toggled ON or OFF for the current programme. (In 1scart model the decoder is
not displayed)
Setting up your unit, continued
19
3. ORGANIZER
3-1.NAME
* Creating of New Names :
Press the [ / ] buttons to select the wanted characters.
(the [ / ] button will be used to move the position of digit).
The [ENTER] button is pressed to confirm that.
To make and memorize the new names for the other channels, repeat the procedure.
3-2. DELETE PR
(1) Press the [SETUP] button to call the Main SETUP in TV mode.
Press the [ / ] buttons to select the line of Installationand press the [ENTER] button to
confirm that.
(2) Press the [ / ] buttons to select the line of “Organizerand press the [ENTER] button to
confirm that.
(3) Press the [ / ] buttons to select the Delete PR..
(4) The [ENTER] button is pressed to confirm that.
The [SETUP] button is pressed to interrupt before pressing the [ENTER] button , the real
picture will appear without storing the data.
(5) To erase another channel, repeat the procedure from step (3) to (4).
Setting up your unit, continued
(2)
(1)
--------------->
SETUP
Clock set
Record timer
Installation
Search
Preferences
ENTER:Confirm SETUP:End
--------------->
--------------->
INSTALLATION
Autoinstallation
Manualinstallation
Organizer
RF outputset
ENTER:Confirm SETUP:End
ORGANIZER
ENTER:Confirm SETUP:End
PR 01
Name ----
Swap with PR --
Delete program. 01
ORGANIZER
ENTER:Confirm SETUP:End
PR 01
Name ----
Swap with PR --
Delete program. 01
20
3-3. SWAP WITH PR
(1) Press the [SETUP] button to call the Setup Menu in TV mode.
Press the [ / ] buttons to select the line of Installationan press the [ENTER] button to
cofirm that.
(2) Press the [ / ] buttons to select the line of organizerand press the [ENTER] button to
confirm that
(3) Press the [ / ] buttons to select the aligning channel and press the [ENTER] button to
confirm that.
(4) The [ / ] buttons are pressed to move the selected PR.
The changed position of the PR number will be memorized whenever the PR is moved by
pressing the [ / ] buttons.
(5) Press the [ENTER] button to confirm that or the [SETUP] button to finish the alignment without
data change.
(6) To align the other channels, repeat the procedure from the step (3) to step (5).
4. RF OUTPUT SET(For stand alone VCR only)
No setting require for TV+VCR/DVD combo.
SETUP
Clock set
Record timer
Installation
Search
Preferences
ENTER:Confirm SETUP:End
INSTALLATION
Autoinstallation
Manualinstallation
Organizer
RF outputset
ENTER:Confirm SETUP:End
Setting up your unit, continued
ENTER:Confirm SETUP:End
PR 01
Name ----
Swap with PR - -
Delete program. 01
--->
--->
---> --->
--->
ENTER:Confirm SETUP:End
PR 01
Name ----
Swap with PR --
Delete program. 01
ENTER:Confirm SETUP:End
PR 02
Name ----
Swap with PR --
Delete program. 01
ENTER:Confirm SETUP:End
PR 01
Name ----
Swap with PR 02
Delete program. 01
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Akura ASDVCR210RS User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI