Diamond Vision DVDV805-03 User manual

Brand: Diamond

Model: Vision DVDV805-03

Category: DVD players

Type: User manual

This manual is also suitable for

DVD / MP3 / CD PLAYER

LECTEUR DVD / MP3 / CD

DVDV805-03

DVDV805-04

mp3

THIS INSTRUCTION BOOK MAY CONTAIN ERRORS AND OMISSIONS.

DESIGN AND SPECIFICATION ARE SUBJECT TO CHANGE WITHOUT NOTICE.

CE LIVRET D’INSTRUCTIONS PEUT CONTENIR DES ERREURS ET DES OMISSIONS. LE

CONCEPT ET LES CARACTÉRISTIQUES SONT SUJETS À CHANGEMENT SANS PRÉAVIS.

OPERATION MANUAL

MANUEL DE FONCTIONNEMENT

IMPORTANT

Since CD circuitry may cause interference with other radio tuners nearby, switch this recorder

off when not in use or move it away from an affected radio tuner.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesirable operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible

for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates

uses and can radiate radio frequency energy and, if not installed and used in accordance with

these instructions, may cause harmful interference to radio communications. There is no

guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio / TV technician for help.

SAFETY CERTIFICATION

This CD player is made and tested to meet safety standards of the FCC, requirements and

compliance with safety performance of the U.S. Department of Health and Human Services,

and also with FDA Radiation Performance Standards 21 CFR Subchapter J.

WARNING

To prevent fire or shock hazard, do not expose this appliance to rain or moisture.

The apparatus should not be exposed to dripping or splashing and that no objects filled with liquids, such

as vases, shall be placed on the apparatus.

The ventillation should not be impeded by covering the ventilation openings with items, such as

newspapers, table-cloths, curtains, etc.

No naked flame sources, such as lighted candles, should be placed on the apparatus.

CAUTION

TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH ANY EXTENSION

CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE PLUG CAN BE FULLY INSERTED

WITHOUT EXPOSING ANY PARTS OF THE BLADES.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING: TO REDUCE THE

RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER

(OR BACK). NO USER-

SERVICEABLE PARTS

INSIDE, REFER SERVICING

TO QUALIFIED SERVICE

PERSONNEL.

The exclamation point within

an equilateral triangle is in-

tended to alert the user to

presence of important operat-

ing and maintenance

(servicing) instructions in the

literature accompanying the

appliance.

The lighting flash with arrowhead

symbol, within an equilateral trian-

gle, is intended to alert the user to

the presence of uninsulated "dan-

gerous voltage" within the

product's enclosure that may be of

sufficient magnitude to constitute

a risk of electric shock to persons.

SAFETY INSTRUCTIONS -

Read before operating equipment

This product was designed and manufactured to meet strict quality and safety standards. There are,

however, some installation and operation precautions which you should be particularly aware of.

1. Read Instructions — All the safety and operating instructions should be read before the

appliance is operated.

2. Retain Instructions — The safety and operating instructions should be retained for future

reference.

3. Heed Warning — All warnings on the appliance and in the operating instructions should be

adhered to.

4. Follow Instructions — All operating and use instructions should be followed.

5. Water and Moisture — The appliance should not be used near water – for example, near a

bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool,

etc.

6. Carts and Stands — The appliance should be used only with a cart or stand that is recom-

mended by the manufacturer.

6A. An appliance and cart combination should be moved with care. Quick stops, ex-

cessive force, and uneven surfaces may cause the appliance and cart combination

to overturn.

7. Wall or Ceiling Mounting — The appliance should be mounted to a wall or ceiling only as

recommended by the manufacturer.

8. Ventilation — The appliance should be situated so that its location or position does not

interfere with its proper ventilation. For example, the appliance should not be situated on a

bed, sofa, rug, or similar surface that may block the ventilation openings; or, placed in built-

in installation, such as a book case or cabinet that may impede the flow of air through the

ventilation openings.

9. Heat — The appliance should be situated away from heat sources such as radiators, heat

registers, stoves, or other appliances (including amplifiers) that produce heat.

10. Power Sources — The appliance should be connected to a power supply only of the type

described in the operating instructions or as marked on the appliance.

11. Grounding or Polarization — The precautions that should be taken so that the grounding

or polarization means of an appliance is not defeated.

CAUTION: To prevent electric shock, match the wide blade of this plug

to the widle slot, fully insert. Do not use this (polarized) plug with an

extension cord, receptable or other outlet unless the blades can be fully

inserted to prevent blade exposure.

12. Power-Cord Protection — Power-supply cords should be routed so that they are not likely

to be walked on or pinched by items placed upon or against them, paying particular atten-

tion to cords at plugs, convenience receptacles, and the point where they exit from the

appliance.

13. Cleaning — The appliance should be cleaned only as recommended by the manufacturer.

14. Power Lines — An outdoor antenna should be located away from power lines.

15. Nonuse Periods — The power cord of the appliance should be unplugged from the outlet

when left unused for a long period of time.

16. Object and Liquid Entry — Care should be taken so that objects do not fall and liquids are

not spilled into the enclosure through openings.

17. Damage Requiring Service — the appliance should be serviced by qualified service per-

sonnel when:

A.The power-supply cord or the plug has been damaged; or

B.Objects have fallen, or liquid has spilled into the appliance; or

C.The appliance has been exposed to rain; or

D.The appliance does not appear to operate normally or exhibits a marked change in per-

formance; or

E.The appliance has been dropped, or the enclosure damaged.

18. Servicing — The user should not attempt to service the appliance beyond that described in

the operating instructions. All other servicing should be referred to qualified service personnel.

Getting Started

Before attempting to connect, operate or adjust this product, please read these instruc-

tions completely and keep this manual for future reference.

Dear customers :

May we take this opportunity to thank you for purchasing this DVD Player.

We strongly recommend that you carefully study the operating instructions before operat-

ing the unit.

Main Features

• Front loading DVD / MP3 / CD player.

• Built-in Dolby Digital.

Standards

Video : NTSC

Audio : PCM (48 or 96 kHz), 2 Channel MPEG layer 2, Dolby AC-3 & dts line out

Features of audio specifications

– DOLBY Digital 2 ch decoding output.

– DTS for Digital (Coaxial) output

– Linear PCM output.

* Player is CD-R, CD-RW compatible.

Note: CD-R, CD-RW Discs recorded with writing device can only be used when they are

correctly treated.

Region Management Information

This DVD Player is designed and manufactured to respond to the Region Management

Information that is recorded on a DVD disc. If the Region number described on the DVD

disc does not correspond to the Region number of this DVD Player, this DVD player can-

not play that disc.

This Region number of this DVD player is .

Disc manintenace

– Before playback, wipe the disc from the center hole toward the outer edge with a clean

cloth.

– Never use benzine, thinner, cleaning fluid, static electricity prevention liquids or any

other solvent.

Note : Dirty disc may cause bad picture.

Audio &

Video

Audio

Disc size 12cm

single side, single layer / single side, double layer

PAL and NTSC DVD disc

Playback time 135min / 240min max.

Disc size 12cm / 8cm

CD disc

Playback time 74min/20min max.

MP3 format disc

Getting Started

Disc types

MP3

Correct

From the center to the edge

Incorrect

Safety precautions

Warning

To avoid electrical shock, do not open the

cabinet, refer servicing to qualified person-

nel only.

Warning

Keep the unit away from flower vases, tubs,

sinks, etc. If liquids are spilt into the unit,

serious damage could occur.

Warning

Do not expose this equipment to rain or

moisture.

Warning

Do not block ventilation holes of the unit so

that air can circulate freely,

Attention

If smoke, malodour or unrelated noise are

emitted from the unit, turn off the power and

disconnect the AC power cord.

Attention

Touching the unit is dangerous especially if

during thunder.

Attention

When left unused for a long period of time,

the unit should be unplugged from the house-

hold AC outlet.

Attention

Be sure to turn the unit off and disconnect the AC

power cord before cleaning the unit surface. If the

surface is dirty, wipe clean with a cloth which has

been dipped in a weak soap and water solution and

wrung out thoroughly, and then wipe again with a

dry cloth.

Note: This unit is a class 1 laser product and uses a visible laser beam which could

cause hazardous radiation exposure if directed. Be sure to operate it correctly as

instructed.

Front Panel Control

1. Disc Tray

2. Power Indicator

a) Steady Light = play mode

b) Blinking Light = standby mode

3. Open/Close Button

4. Play / Pause Button

5. Stop Button

6. Remote Sensor

7. Power ON/OFF

Rear Panel Control

1. AC Power Cord

2. Y/Pb. Cb/Pr. Cr output

3. Video output (composite)

4. Analog Audio output

5. Digital Audio output (coaxial)

6. S-Video output

Battery installation (remote control unit)

1. Remove the battery cover.

Insert two batteries (AAA) making sure the polarity (+/-) matches the marks inside the unit.

3. Replace the cover.

– Do not attempt to recharge, short-circuit, disassemble, heat or throw the batteries into

the fire.

– Do not mix old and new batteries

– Dispose of properly in accordance with local law.

Note : Weak batteries can leak and severely damage

the remote control unit.

Remote Control Unit

1. Power on/off Button

2. Numeric Buttons

3. Display Button

4. Volume – Button

5. Setup Button

6. DVD Menu Button

7. Direction Buttons

( Up  / Down/ Left/ Right)

8. Fast Backward Button

9. Play Button

10. Stop Button

11. Slow Button

12. Subtitle Button

13. P. Scan Button

14. Search Button

15. Audio Button

16. Zoom Button

17. Eject Button

18. Volume + Button

19. Mute Button

20. Previous Button

21. Next Button

22. Enter Button

23. Fast Forward Button

24. Step/Pause Button

25. Program Button

26. Angle Button

27. Cancel Button

28. Repeat Button

29. Repeat A-B Button

Connect To TV

Caution : Turn off all te equipment before any installation.

This unit provides several types of video and audio signals output. They are :

• Y/Pb, Cb/Pr, Cr output

• RCA output

• S-Video Output

User can choose a suitable connection type to connect the player to TV.

1. Y/Pb, Cb/Pr, Cr output

2. Connection via Composite (RCA) Cable

In this type of connection, we have to connect the Left/Right Audio Cables (Red and

White) and a Video signal (Yellow).

3. Connection via S-Video Cable

Component Video

(Y/Pb, Cb/Pr, Cr)

Video in

Audio in R

Audio in L

S-Video in

Audio in R

Audio in L

Connection to Amplifier

There are four different types of connection between the DVD player and an amplifier.

• Digital output via Coaxial Cable (Connection 1).

• 2 channels (left/right) Audio Output (connection 2-3)

Note:

1. The Digital output cut off, when Analog output was selected.

2. The Analog output cut off, when Digital/Optical output was selected.

Video output

Operation

TV Selection

Turn on the TV, the DVD player and the Audio Amplifer System (if any).

1. Press the “TV/VIDEO” button on the TV.

2. Select the Video Mode (TV).

Note: If there are more than 1 AV channel for the TV, select the channel you have

connected to the DVD player.

3. Select the Correct Audio Input on the AV Amplifier (if any)

Play Discs

1. Press the OPEN/CLOSE button ( ) on the front panel and load the Disc on the

tray. The label side should be facing upwars. For a Double-sided DVD Disc, put the

disc with label A/1 up.

2. Press the OPEN/CLOSE button ( ) again to close the tray and the disc will be

loaded.

3. The Disc will be played automatically.

• If it is a DVD disc, it will show the Menu/Title Page on the screen.

• If it is a CD, it will play the first track directly.

4. Press the STOP button ( ) if you want to stop the Disc playback. You can resume

playback by pressing the PLAY button and it will start at the location where you have

pressed stop (Resume Play).

5. Press the STOP button twice to have the Disc stop completely.

Pause /Step

This function is applicable for DVD and CD audio.

• For DVD, the picture will freeze.

• For CD audio, it will become muted.

1. Press the PAUSE button ( ) to pause play.

2. Press the PLAY button again to resume Play.

DVD Setup Mode

• Setup Mode provides the menu for the configuration of TV DISPLAY Mode, OSD

LANGUAGE Mode, AUDIO Mode, PARENTAL Mode, PASSWORD, etc.

• Item selection in the SETUP menu is done by using the Direction button and the

ENTER button.

• To exit the SETUP menu, press the SETUP button again.

• The initial password for PARANTAL Mode is set at 1369.

Note: To setup the TV display mode, must be in stop mode.

Setup Menu Items :

Press the SETUP button on the remote control.

The following menu will be shown:

1. GENERAL SETUP

TV DISPLAY

• Normal/PS

This is selected when the DVD player is con-

nected to a normal TV. Wide-screen imaged are

shown on the screen, but with some parts cut

automatically.

• Normal/LB

This is selected when the player is connected to

a normal TV. Wide screen images are shown on

the screen, with black belt on the top and bottom.

• WIDE

This is selected when the player is connected to a wide-screen TV.

ANGLE MARK

This only works when there is an angle mark on

the disc. Select ON, the screen shows the mark

when playing DVD.

- ON

- OFF

OSD LANGUAGE

This used to select the OSD language.

- English

- Spanish

- German

- French

CAPTIONS

This option can show or hide the captions.

- On (Show captions)

- Off (Hide captions)

-- GENERAL SETUP PAGE --

TV Display LB

Angle Mark On

OSD Lang ENG

Captions Off

Screen Saver On

Go To General Setup Page

-- GENERAL SETUP PAGE --

TV Display

Angle Mark English

OSD Lang



French

Captions

German

Screen Saver

Spanish

Set OSD Language

-- GENERAL SETUP PAGE --

TV Display



NORMAL/PS

Angle Mark

NORMAL/L2

OSD Lang WIDE

Captions

Screen Saver

Set TV Display Mode

-- GENERAL SETUP PAGE --

TV Display

Angle Mark

OSD Lang

CAPTIONS



Screen Saver

OFF

Closed Caption

-- GENERAL SET UP PAGE --

TV Display

Angle Mark



OSD Lang

OFF

Captions

Screen Saver

Set Angle Mark

SCREEN SAVER

Start the screen saver, the screen saver image

appears when the player stops or the image is

frozen for a few minutes. This saver can keep

the screen from being damaged.

- ON (Start the screen saver)

- OFF (Remove the screen saver)

2. SPEAKER SETUP

When SPEAKER SETUP option is selected, the

following menu will be shown.

DOWNMIX

• LT/RT

A disc recorded multi channel soundtrack, the

output signal will be incorporated to left and right

channel.

• STEREO

A disc record multi channel soundtrack, the

output signal will be incorporated to stereo.

DOLBY DIGITAL SETUP

• DYNAMIC

This option is used to set the compression ratio in

order to control the sound (volume) contrast.

3. VIDEO SETUP

When VIDEO SETUP option is selected, the

following menu will be shown. To select the

desired item use the direction ( /// )

button.

• VIDEO OUT : CVBX/S-VIDEO

YUV

• VIDEO TV : P-SCAN

INTERLACE

Note : To select P-SCAN mode, the P-SCAN

output must be connect to P-SCAN TV, otherwise

the picture will be unstable.

-- SPEAKER SETUP PAGE --

Downmix



LT/RT

Dynamic

Stereo

Set Downmix Mode

-- SPEAKER SETUP PAGE --

Downmix

FULL

Dynamic  3/4

1/2

1/4

0FF

Set DRC to 1/2 Conpression

-- VIDEO SETUP PAGE --

Video Out



CVBS/S-VIDEO

TV Mode

YUV

-- VIDEO SETUP PAGE --

Video Out

TV Mode

 P-SCAN

Interlace

-- GENERAL SETUP PAGE --

TV Display

Angle Mark

OSD Lang

Captions

Screen Saver



OFF

SCREEN SAVER

4. PREFERENCE SETUP

AUDIO

If a language listed below is recorded on the disc,

you can play the sound in such language. If not,

the language recorded will be used.

- English

- French

- Spanish

- German

SUBTITLE

If a language listed below is recorded on the disc,

you set the subtitle to be displayed in such

language. If not, the language recorded will be

used.

- English

- French

- Spanish

- German

-Off

DISC MENU

If a language listed below is recorded on the disc,

you can set the Menu to be displayed in such

language. If not, the language recorded will be

used.

- English

- French

- Spanish

- German

PARENTAL

When playing disc with parental lock function,

you may select an age control grade according to

grade of disc and your own preference.

For example, if PG is selected, DVD Video disc

rated higher than the PG guide cannot be played.

- KID SAF

-G

-PG

- PG 13

- PGR

-R

- NC 17

- ADULT

- OFF

PREFERENCE SET UP PAGE

Audio



English

Subtitle French

Disc Menu Spanish

Parental German

Password

Default

Preference Audio Languages

PREFERENCE SET UP PAGE

Audio

Subtitle



English

Disc Menu French

Parental Spanish

Password German

Default Off

Subtitle

PREFERENCE SET UP PAGE

Audio

Subtitle

Disc Menu



English

Parental French

Password Spanish

Default German

Preference Disc Menu Languages

PREFERENCE SET UP PAGE

Audio

Subtitle

Disc Menu

Parental



KID SAF

Password G

Default PG

PG-13

PGR

NC17

ADULT

OFF

Set Parental Control

PASSWORD : OLD ______

NEW ______

VERIFY ______

Move the cursor to the “PASSWORD” item and press ENTER button to confirm and

then input the secret code “1369”. After confirmation, you are required to input new

secret code and then press ENTER button to confirm. and retreat to the “Custom

setup” interface.

Warning: Please remember the new secret code, otherwise you will not able to

change the Parental Control. Please contact the agent or our company if you forget

the secret code.

DEFAULT

User can load the original factory settings by

choosing RESET and pressing ENTER.

- RESET

DVD Menu Play

The DVD Menu Play function is only applicable for DVD movie. User can access the

Casting informationm, Production History, Movie Introduction etc. directly through this

function.

1. Press the DVD MENU button on the remote control to enter the Root Menu.

2. Use the Direction button () or input the item index through the Number keys

(0-9) to do the selection.

3. Press ENTER to confirm the selection.

Progressive scan creates a picture with double the scan lines of traditional component

video pictures and creates a sharper image. The advantages of progressive scan video

output are reduced picture flickering and motion artifacts as well as a sharper image on

large screens.

Audio

This funciton is applicable for DVD and CD audio but with different effects.

- Pressing AUDIO button will change the Audio channel.

REW / F.F. ( / )

This function is applicable for DVD and CD audio but with different effects. The FAST

FORWARD key and FAST BACKWARD key are used to achieve fast play function.

- For DVD, there are 5 different levels of speed (2x, 4x, 8x, 16x, 32x). Every succes-

sive key press will increment the speed of quick play.

- For CD audio, the FORWARD/BACKWARD will perform quick rolling on the music

output.

Note : Press PLAY button at any stage will resume to normal speed.

PREFERENCE SET UP PAGE

Audio

Subtitle

Disc Menu

Parental

Password

Default



Reset

Preference Menu Languages

PREV. / NEXT ( / )

During playback, press one of the PREV. / NEXT buttons (PREVIOUS button and NEXT

button)

- When the PREV. button is pressed once, the pickup returns to the beginning of the

PREVIOUS playing chapter or track.

- When the NEXT button is pressed once, the pickup will go to the beginning of next

chapter or track.

P. SCAN (PROGRESSIVE SCAN)

Press this button to enter to the P-SCAN mode. Press this button again switch back to

normal interlace mode.

Note : To select P-SCAN mode, the P-SCAN output must be connect to P-SCAN TV,

otherwise the picture will be unstable.

Slow F.F.

The Slow Forward is applicable for DVD. There are 4 steps of slow motion speed, 1/2,

1/4, 1/8, 1/16. Successive key presses will decrement the playback speed.

Note: Press PLAY button to switch back to normal playback speed.

Repeat Mode

This function is applicable for DVD and CD audio but with different effects.

- For DVD disc playback, user can choose to repeat the current chapter, current title

or disc. Subsequent key press of the REPEAT key can change between these three

options.

- For CD, user can choose to repeat the current track or the whole disc (Repeat All).

Subsequent key press of the REPEAT key can change between these two options.

A – B

This function is applicable for DVD and CD audio. User can specify the repeating

interval by marking the starting point and the end point.

1. Press the A-B button to mark the starting point (Playback will continue).

2. Press the A-B button to mark the end point (The marked part will be repeated

automatically.)

Note : Press the A-B button during repetition will disable the Repeat mode.

Subtitle

This function is only applicable for DVD disc. It can change the subtitle language shown

on the screen.

Note : Number of subtitle available depends on the DVD disc.

Angle

Some discs may have multiple viewing angles during production. The ANGLE button is

to select the viewing angle shown on the screen.

Note : The number of Angle of View depends on the disc.

This function is applicable for DVD and CD audio. Through this function, the user can

access a specific location or a specific track by key in the target time or the track

number.

1. Press the SEARCH button to enter the Search Mode.

2. Input the target time through the Number keys (0-9) and the player will jump to the

target location immediately.

Display (Remain Time)

This function is applicable for DVD only. It will display the timing information of the

playback on the screen.

- For DVD playback, subsequent key presses on the DISPLAY button will show the

Title Elapsed Time, Title Remain Time, Chapter Elapse Time and Chapter Remain

Time one by one.

Play

This function is applicable for DVD and CD audio. During the disc playback, when the

STOP button is pressed once, the player will enter the Resume Play mode. At this time,

if the PLAY button is pressed, the player will resume playback at the location where the

STOP button is pressed. If the STOP button is pressed (i.e. STOP button is pressed

twice), the player will be stop.

Zoom

This function is applicable for DVD. User can enlarge a static picture or a moving

picture by pressing the ZOOM button. There are 3 levels of zooming (2x, 3x and 4x)

and they can be achieved one by one through subsequent key presses on the ZOOM

key.

NOTE: user can select the portion of the picture to be enlarged by using the Direction

button ().

Press the DISPLAY Button TITLE ELAPSED

TT 01/04 CH 01/02 0:02:13

Press the DISPLAY Button TITLE REMAIN

TT 01/04 CH 01/02 1:33:30

Press the DISPLAY Button CHAPTER ELAPSED

TT 01/04 CH 01/02 0:02:15

Press the DISPLAY Button CHAPTER REMAIN

TT 01/04 CH 01/02 0:02:18

Press the DISPLAY Button DISPLAY OFF

Program Mode

This function is applicable for DVD and CD audio. User can assign the playback

sequence according to his/her preference. For CD audio, user can assign the track

sequence while for DVD disc, user can assign both the Title and Chapter sequence.

1. Press the PROGRAM button. The Program

Sequence tabel will be shown on the screen.

2. Enter the track number according to the user

preference through the Number keys (0-9).

3. After assigning the playback sequence, move

the highlight cursor to the START opiton by

using the Navigation Arrows. Press ENTER on

the remote control to confirm.

To remove the program:

Move the highlight cursor to desired Program by

using the Navigation arrows then press the CLEAR

button to remove the selected program.

PROGRAM

01 _ _ 06 _ _

02 _ _ 07 _ _

03 _ _ 08 _ _

04 _ _ 09 _ _

05 _ _ 10 _ _

EXIT START NEXT

I

PROGRAM

01 0 5 06 _ _

02 0 3 07 _ _

03 0 8 08 _ _

04 _ _ 09 _ _

05 _ _ 10 _ _

EXIT START NEXT

I

PROGRAM

01 0 5 06 _ _

02 0 3 07 _ _

03 0 8 08 _ _

04 _ _ 09 _ _

05 _ _ 10 _ _

EXIT START NEXT

I

MP3 OPERATION

This unit can support ISO9660 file system CD-ROM navigation. Multi-Media files such

as MP3 can be played in the DVD player.

Operation

• Insert the MP3 disc into the tray. Navigation Menu will be displayed. The menu will

show the files in the root directory, and the MP3 files then be play automatically.

• In the MP3 menu shows a blue and an orange cursor. The blue cursor indicates the

currently playing MP3 song, the orange cursor indicates a title to be selected.

You can select the other songs by the nevigation arrow buttons or directly input the

song number by pressing the number keys. The orange cursor will move to the

selected song. Then press ENTER button to confirm.

Note :

• There are three digits displayed. If you want call up a title with only one or two digits,

you can either start the entry with “0” or “00”, or you can enter the number of the song

and then wait a few seconds until the cursor skips to the selected title.

• Press the REPEAT button to select : Random (playback in random order), Single

(play one title, then stop), Repeat One (repeat the current title), Repeat Folder (repeat

current folder).

Picture CD

Digital picture (JPEG) from a digital camera can be burnt to a disc and played on this

DVD Player. Insert a picture CD into the tray and the disc will be loaded automatically.

If the disc type can be identified, the player will start showing the pictures one by one

(Side Show Mode).

Operations:

During Slide Show Mode:

• Pressing the PAUSE button will freeze the screen, so that the current picture can be

held for a long time. To resume the slide show mode, press PLAY button.

• Pressing the NEXT button on the remote control will skip the next picture.

• Pressing the PREVIOUS button on the remote control will repeat the current picture.

Blue cursor

Orange cursor

MP3

SONG 001

MP3

SONG 002

MP3

SONG 003

MP3

SONG 004

MP3

SONG 005

MP3

SONG 006

TROUBLE SHOOTING

Check the following guide for the possible cause of a problem before contacting service.

Symptom

No Power

The power is on, but DVD

player does not work

No Picture

The playback picture is poor

The DVD player does

not start playback

No Sound

The Remote Control

does not work properly

Cause

• The power cord is disconnected.

• No disc is inserted.

• The TV is not set to receive DVD

signal output.

• The video cable is not connected

securely.

•

The connected TV power is turned off.

• The equipment connected with the

audio cable is not set to receive

DVD signal output.

• The audio cable is not connected

securely.

•

The power of the equipment connected

with the audio cable is turned off.

• The Digital Audio Output is set to

the wrong position.

• The disc is dirty.

• No disc is inserted.

• An unplayable disc is inserted.

• The disc is placed upside down.

• The disc is not placed with the

guide.

• The disc is dirty.

• A menu is on the TV screen.

• The Rating level is set.

•

The remote control is not pointed at

the remote sensor of the DVD player.

• The remote control is too far from

the DVD player.

•

There is an obstacle in the path of the

remote control and the DVD player.

• The batteries in the remote con-

trol are exhausted.

Correction

• Plug the power cord into the wall

outlet and unit securely.

•

Insert a disc. (Check that the DVD or au-

dio CD indicator in the DVD display is lit.)

•

Select the appropriate video input mode

on the TV so the picture from the DVD

player appears on the TV screen.

• Connect the video cable into the

jacks securely.

• Turn on the TV.

• Select the correct input mode of the

audio receiver so you can listen to the

sound from the DVD player.

• Connect the audio cable into the

jacks securely.

• Turn on the equipment connected with

the audio cable.

•

Set the Digital audio Output to the correct

position, then turn on the DVD player

again by pressing the POWER button.

• Clean the disc.

• Insert a disc

•

Insert a playable disc. (Check the disc

type, color system and Regional code.)

•

Place the disc with the playback side down.

• Place the disc on the disc tray cor-

rectly inside the guide.

• Clean the disc.

• Press the SET UP button to turn off

the menu screen.

• Cancel the Rating function or change

the rating level.

• Point the remote control at the remote

sensor of the DVD player.

• Operate the remote control within

about 23ft (7m).

• Remove the obstacle.

• Replace the batteries with new ones.

Page is loading ...

Diamond Vision DVDV805-03 User manual

Brand: Diamond

Model: Vision DVDV805-03

Category: DVD players

Type: User manual

This manual is also suitable for

Download PDF

report

in other languages

français: Diamond Vision DVDV805-03 Manuel utilisateur

Diamond Vision DVDV805-03 User manual

This manual is also suitable for

Diamond Vision DVDV805-03 User manual

in other languages

Related papers

Other documents