Ransomes 67966 67995 67968 67996 67970 67993 67975 67965 Accessories Manual

Brand: Ransomes

Model: 67966 67995 67968 67996 67970 67993 67975 67965

Category: Lawnmowers

Type: Accessories Manual

Instruction

Sheet

When Performance Matters.

™

WARNING

If incorrectly used, this machine can cause severe injury. Those who use

and maintain this machine should be trained in its proper use, warned of its

dangers and should read the entire manual before attempting to set up,

operate, adjust, or service the machine.

1-INCLUDESITEMS3 -16

Turf Groomer

22 Inch x 5 Inch Reel

67966 – Left Hand 1/4 Inch Spacing

67995 – TrueSet

™

Left Hand 1/4 Inch Spacing

67968 – Left Hand 1/2 Inch Spacing

67996 – TrueSet

™

Left Hand 1/2 Inch Spacing

18 Inch x 5 Inch Reel

67970 – Left Hand 1/4 Inch Spacing

67993 – TrueSet

™

Left Hand 1/4 Inch Spacing

26 Inch x 5 Inch Reel

67975 – Left Hand 1/2 Inch Spacing

Fixed Head Mower Adapter Kit

67965 – Adapter Kit for Eclipse

™

118, 122, and 126 Mowers

4170860-Rev B

This kit is intended for use on all 5 in. (127 mm) diameter

cutting units.

1. Park the mower on a flat and level surface, fully lower

the attachments to the ground, engage the parking

brake, tur n the ignition switch to the OFF position, and

remove the key.

a. Wait for all movement to stop before making any

adjustments or modifications.

b. Allow sufficient time for the unit to cool down.

c. Take this opportunity to thoroughly inspect the

equipment and perform other required maintenance.

Groomer Identification_________________________________________________

1. The Turf Groomer has been pre assembled into one

assembly, three loose parts, and a bag of parts.

2. To help in the assembly process, completely install

each Turf Groomer before starting on the next reel.

a. Open each carton to inspect and familiarize your-

self with the contents.

b. Keep all components in original carton until ready

for assembly.

3. Eclipse 118, 122, and 126 Fixed Head Mowers:

Using a hoist or mechanic’s lift move entire mower over

to workbench and proceed with fixed head groomer

installation instructions on Page 3.

4. Eclipse 118F, 122F, and all Riding Mowers: Remove

the reels from the mower following directions given in

the mower’s Parts & Maintenance Manual.

Move one reel and corresponding groomer assembly to

workbench. [See ]

CAUTION

Before you install this kit, read the mower’s Safety &

Operation Manual to become familiar with the mower,

the controls, and proper use of the equipment.

Stay alert for potential hazards and follow all safety

precautions. Read all instructions completely and make

sure you understand them before proceeding with the

assembly.

WARNING

Before you attempt to clean, adjust, or repair any of this

equipment, lower the attachments, disengage all drives,

shut down the engine, and allow the unit to cool.

Remove the key from the ignition switch and disconnect

the Negative (BLACK) battery cable, or power

connector, to prevent accidental discharge and potential

bodily injuries.

Be careful to prevent entrapment of the hands and

fingers between moving and fixed components of the

machine.

To prevent personal injury and damage to the cutting

edges handle the reel with extreme care. Always wear

gloves when picking up or moving reels or groomer

blade assemblies.

Litho in U.S.A. 5-2013

Fixed Head Mower Groomer Kit _________________________________________

In addition to the groomer kit, the Fixed Head Groomer Kit

part number 67965 is also required to convert the mower.

Callouts identified with a single letter (A) through (H) are

part of the mower. Refer to the mower’s manual for part

numbers.

Callouts with a double letters (AA) through (AN) are parts

of the fixed head groomer kit 67965. Refer to the parts list

in this manual for parts identification.

Callouts with triple letters (AAA) through (AAG) are parts

of the groomer kit. Refer to the parts list in this manual for

parts identification.

1. Remove and discard existing hardware (B) and shaft

cover (A).

2. Remove grass catcher if installed.

3. Tip mower back just enough to take all weight off the

front roller. Secure mower in this position.

4. Remove hardware (C and D) from each side of mower.

Retain hardware (C) and discard hardware (D).

5. Slide front roller, roller adjuster brackets, and grass

catcher bracket as an assembly away from front of

mower. Save parts in a secure area for future use.

6. Loosely assemble left (AA) and right (AB) side mounts

to mower frame using hardware (C). Temporarily install

reference hardware (see Figure 7) to locate template.

Butt template against seal carrier for proper alignment.

Tighten hardware C. Flip template for right hand side

and align with bearing housing.

7. Assemble adapter plate (AD) to left reel housing (E)

using 1/4-20 x 1 in. socket head screws (AE).

8. Assemble seal (AAA) to adapter plate (AD).

9. Remove screw (F), washer (G), and spacer (H).

10. Assemble 7/8 x 13/32 in. spacer (AAB) from groomer

kit and spacer (AN) onto the reel shaft.

11. Insert key (AAC) into slot on reel shaft.

12. Slide pulley assembly (AAD) onto reel shaft and secure

with screw (AP), lockwasher (AF), and washer (G).

NOTE: Pulley may also be assembled to mower when

installing the belt. If the pulley is installed here it may need

to be removed and reassembled later.

Figure 1

Figure 2

Figure 3

Figure 4

Figure 5

AAA

Reference

Hardware

Template

(Shown flipped

for Right Side)

AAD

AAC

AAB

13. Remove mounting hardware (AAE, AAF, and AAG)

from groomer assembly. Retain washer (AAE) and

slide spacer (AAF). Discard all hardware labeled

(AAG).

14. Assemble groomer assembly to mower.

a. Slide left end of groomer over adapter plate then

move right side of groomer into position. Make

certain slide spacers (AAF and AK) are in place

between groomer and side mounts (AA and AB).

b. Secure groomer assembly to mower frame using four

5/16-18 x 2 in. hex head screws (AG), lockwashers

(AH), two flat washers (AJ), and washers (AAE).

c. Adjust groomer (if required) to slide 5/16-18 x

2-1/2 in. carriage bolts (AL) into position. Secure with

5/16-18 spiralock flange nuts (AM).

15. Proceed with Groomer Adjuster Knob assembly.

See page 7.

Figure 6

Figure 7

AAE

AAF

AAG

AAF

AAE

Eclipse 118F, 122F, and Riding Mowers Assembly __________________________

Callouts identified with a single letter (A) through (N) are

part of the mower. Refer to the mower’s manual for part

numbers.

Callouts with a double letters (AA) through (AD) are parts

of the template kit 4160552. Refer to the parts list in this

manual for parts identification.

Callouts with triple letters (AAA) through (ABN) are parts

of the groomer kit. Refer to the parts list in this manual for

parts identification.

1. Remove existing front roller (A), roller scraper (B - If

installed), hardware (D) front roller adjusting brackets

(C), and adjusting knobs (E).

NOTE: Lift yoke is not shown for clarity. Do not remove lift

yoke from reels.

2. Remove hardware (G and H) and counterweight (F).

Retain lockwashers (G).

3. Block reel with a piece of wood, remove retaining

hardware (J) and spacer (K). Retain hardware (J) and

discard spacer (K).

NOTE: Place cover over both bearing housing openings to

prevent contamination.

4. Modify frame for mounting groomer.

NOTE: Frame template is not part of the groomer kit and

must be ordered separately. Order Kit number 4160552 for

the template. All Eclipse mowers and reels manufactured

after mid 2007 will not require the template.

a. Determine if frame has required hole (M) on both

ends of reel frame. If holes are present skip to Step

b. If holes (M) are not present align slotted hole in

template with slotted hole of reel frame. Assemble

template (AA) to reel frame using 1/4-20 x 1 in.

screw (AB) and nut (AC).

NOTE: Hole location is cr itical to smooth operation of

groomer adjustment. Holes not located properly may

cause adjusting mechanism to bind.

c. Using hole (AD) in template as a guide drill one new

11/32 in. (9 mm) hole in side of frame.

d. Repeat for other side of reel frame. Discard template

and mounting hardware.

5. Remove and discard lift yoke hardware (N). Keep lift

yoke in position.

6. Remove spacers (AAE), slide spacers (AAF) and

hardware (AAK~AAM).

Figure 8

Figure 9

Figure 10

Figure 11

AAE

AAF

AAK

AAL

AAM

AAL

AAK

AAM

AAL

AAK

Figure 12

7. Assemble seal (AAA) to bearing housing.

8. Eclipse 322, 122F, and 118F Mowers Only: Assemble

weight (ABN) to reel frame using 1/4-20 x 1-1/4 in. hex

head screw (ABP), lockwasher (ABR), flat washers

(ABS), and nut (ABT).

9. Assemble groomer assembly to mower.

a. Slide left end of groomer over reel shaft then move

right side of groomer into position. Make certain slide

spacers (AAF) are in place between groomer and

reel frame.

b. Secure groomer assembly to mower frame using

hardware (AAK) as shown.

Note: It may be necessary to pry up slightly on grass shield

to install socket head screws (AAK).

c. Assemble hardware (AAL) through groomer

assembly, lift yoke, and into reel frame.

d. Verify side plates rotate freely on reel. If required

remove screw (ABN), lockwasher (ABO), flat washer

(ABM), and spacer (ABQ). Adjust locknut (ABU) until

groomer rotates freely. Assemble in reverse order.

e. Adjust groomer (if required) to slide 5/16-18 x

2-1/2 in. carriage bolts (AAM) into position. Secure

with 5/16-18 spiralock flange nuts (AAM).

10. Eclipse 322, 122F, and 118F: Assemble cover plate

(AAH), weight (ABJ), and weight cover (ABK) to

bearing housing using two 1/4-20 x 1-1/4 in. socket

head screws (ABL) and lockwashers (G).

All other reels: Assemble cover plate (AAH) to bear-

ing housing using two 1/4-20 x 1/2 in. socket head

screws (AAJ) and lockwashers (G).

Figure 13

Figure 14

AAF

AAL

AAK

AAL

AAE

AAM

AAK

ABN

ABR

ABP

ABS

ABT

AAA

AAH

AAJ

ABJ

ABK

ABL

ABT

ABQ

ABU

ABM

ABO

ABN

Groomer Adjuster Knob Assembly ______________________________________

1. Assemble grease fittings (AAP) onto adjuster knobs

(AAN). Thread knobs onto adjuster studs.

2. Assemble adjuster bracket (AAS) to push plate (AAR)

using spacer (AAT) and locknut (AAU). Do not

overtighten locknut. Bracket must pivot freely. Repeat

for second bracket and push plate.

3. Assemble adjuster bracket assemblies onto groomer

using 5/16-18 x 5/8 in. screws (AAW), pivot spacers

(AAV), and washers (AAX).

NOTE: Only use the lower notch of groomer knobs.

Figure 15

Groomer Belt ________________________________________________________

1. Loosen hardware (AAZ) and eccentric hardware (AAY)

on drive end of groomer.

2. Rotate eccentric to move groomer shaft in slot so

groomer shaft and reel shaft are as close together as

possible.

3. Assemble 7/8 x 13/32 in. spacer (AAB) onto the reel

shaft.

4. Insert key (AAC) into slot on reel shaft.

5. Slide belt (ABB) over pulley (AAD). Slide pulley

assembly (AAD) and belt onto reel shaft and groomer

pulley. Secure with hardware (F).

NOTE: For fixed head Eclipse mowers remove the pulley

assembly and reassemble with the belt. Refer to Figure 4

for fixed head reel shaft pulley installation.

NOTE: It may be required to remove hardware (AAY and

AAZ) and adjusting link (ABA) to move adjuster shaft

enough to install the belt. If removed, parts must be

installed before proceeding.

6. Place a deep well socket on eccentric (AAY) and turn

to tighten belt (ABB).

NOTE: Use a deep well socket without the ratchet. The belt

must be adjusted with hand pressure only.

7. Hold socket securely and torque hardware (AAZ) to 20

ft lb (27 Nm).

8. Remove socket and torque retaining nut (AAY) to 8-10

ft lb (11-13 Nm).

Figure 16

Figure 17

AAN

AAP

AAN

AAV

AAW

AAR

AAS

AAT

AAX

AAU

AAP

AAY

AAZ

ABA

ABB

AAB

AAC

AAD

AAY

AAZ

ABA

ABB

Belt_________________________________________________________________

NOTE: To prevent permanent damage to the belt do not

overtighten, twist, fold or bend the belt.

Overtightening the belt may cause premature belt failure

and abrasive wear of the pulley and bearings. Twisting or

bending the belt will permanently damage the cord fibers of

the belt.

1. Once the belt has been adjusted as described in the

assembly process no further adjustment is required.

2. Periodic inspections of the belt will be required to check

for wear.

3. Spare belts should be stored individually and not

compressed or bent into any form other than elliptical.

Groomer Roller Adjustment ____________________________________________

Groomer roller was adjusted at the factory but may have

moved during shipment and assembly.

1. Loosen set screws in outer nuts (ABV) and inner nuts

(ABW) on both ends of roller. Loosen outer nuts.

2. Adjust inner nuts (ABW) as required on both ends of

roller to center blades between roller grooves.

3. Tighten outer nuts (ABV) to lock adjustment in place

4. Tighten all four set screws in nuts.

5. If any threads remain exposed after tightening groomer

roller nut (ABV) remove nut and add washer(s) (AAR)

as required between nut and groomer side plate. When

no threads are visible repeat Steps 3 and 4.

Figure 18

Figure 19

Wheel Assembly_______________________________________________________

1. Place anti scalp wheel (ABU) over end of roller and

secure in place with flat washer (ABP), lockwasher

(ABS) and screw (ABR). Tighten hardware.

2. Repeat for other side.

Figure 20

ABV

ABW

ABV

ABW

AAR

(as necessary

ABU

ABP

ABS

ABR

Groomer Belt Cover ___________________________________________________

1. Apply grease to seal lip and to flat area of groomer

pulley that the seal will ride on.

2. Assemble groomer cover (ABC) and pulley cover

(ABD) to groomer.

3. Secure with two #10-24 x 2 in. screws (ABE), four

lockwashers (ABF), flat washers (ABG) and two #10-

24 x 2-1/4 in. screws (ABH).

Figure 21

ABC

ABD

ABF

ABG

ABH

ABE

Adjustments _________________________________________________________

1. Adjustments and maintenance should always be

performed by an qualified technician. If proper

adjustment cannot be made contact an author ized

Jacobsen Dealer.

2. Do not wear jewelry or loose fitting clothing when

adjusting or repairing any equipment.

3. Inspect the equipment on a regular basis. Establish a

maintenance schedule and keep detailed records.

a. Keep the mower clean and moving parts properly

adjusted and lubricated.

b. Replace worn or damaged parts before operating the

machine.

c. Keep shields in place and all hardware securely

fastened.

4. Use the illustrations in the Parts & Maintenance

Manual as reference for the disassembly and

assembly of components.

General Recommendations_____________________________________________

1. Initially expect an increased amount of grass removal

when using the Turf Groomer. Also expect an increased

amount of wear on the reel and bedknife, therefore,

sharpening will be required more frequently. With

continued usage, however, the frequency of

sharpening will decline.

2. Do not use the Turf Groomer immediately following top

dressing as the blades will pick up the top dressing and

pass it through the reel. The groomer should be raised

to its highest position.

3. Use the Turf Groomer on a regular basis. However, if

you wish to skip a day, the Turf Groomer should be

raised to its highest level. The blades will rotate though

the grooves in the roller and keep the roller grooves

clean.

Height of Cut ________________________________________________________

Before this attachment can be put into regular use several

passes should be made over a test area with each pass at

a different setting to obtain the best possible results for your

turf conditioning needs.

1. Record the settings and conditions during the first test.

Examine the test area a few days after the first

grooming and record the results.

2. Your requirements will determine the final settings and

they will be governed by the type and condition of the

grass, temperature, and season of the year, the

frequency of cut and many other variables.

3. Keep in mind that the conditions and settings will vary

from green to green and from one season to the next.

NOTE: Over grooming can cause severe damage to turf.

WARNING

Before you attempt to clean, adjust, or repair any of this

equipment, lower the attachments, disengage all drives,

shut down the engine, and allow the unit to cool.

Remove the key from the ignition switch and disconnect

the Negative (BALCK) battery terminal, or power

connector, to prevent accidental discharge and potential

bodily injuries.

Be careful to prevent entrapment of the hands and

fingers between moving and fixed components of the

machine.

To prevent personal injury and damage to the cutting

edges handle the reel with extreme care. Always wear

gloves when picking up or moving reels or groomer

blade assemblies.

Reel and Groomer Height of Cut_________________________________________

1. To set the cutting height for the reel loosen the wing nut

(D) and thread screw (A) in or out to obtain the desired

height of cut (B) on gauge bar (C).

a. Use a small metal scale to measure dimension (B)

as the height of cut. Once dimension (B) is obtained

tighten wing nut (D).

b. Loosen wing nut (G). Set the groomer height by

threading groomer height screw (H) in or out. Tighten

wing nut. Groomer height must not be less than 1/2

of reel height of cut (B).

NOTE: Do not set the blades at ground level or below.

Mowing at this level may damage the machine as well as

the turf. The Turf Groomer is designed to allow maximum

groomer depth of one-half height of cut and is to be used

as a conditioner not a vertical mower.

NOTE: Jacobsen does not recommend setting the

groomer blades at less than half of the reel cutting

height. This height will also help eliminate natural graining

and smooth out uneven grass.

2. Loosen hardware (E) on both ends of the reel just

enough to allow inside knobs (F) to raise or lower the

roller.

NOTE: Only use lower notch on groomer knobs.

3. Place gauge bar across the front and rear rollers at one

end of the reel.

4. Slide the head of screw (A) over the bedknife and

adjust knob (F) to close the gap between the screw

head and the bedknife.

5. Repeat adjustment on opposite end of reel.

6. Recheck both ends of reel for proper adjustment and

tighten hardware (E).

7. Loosen hardware (J) just enough to allow outside

knobs (K) to raise or lower the groomer.

8. Place the gauge bar across the front and rear rollers on

one end of the reel with head of screw (A) over the

bedknife.

9. Adjust knobs (K) to close gap between screw and

groomer blades. Repeat at other end of reel.

10. Tighten hardware (J).

11. Make absolutely certain that each Turf Groomer is

adjusted evenly on both ends and that all the cutting

units on the mower are adjusted to the same height.

Figure 22

Raising Groomer _____________________________________________________

Note: The groomer is designed to be always ON whenever

the reel is tur ning.

1. The groomer blades should be raised to their highest

position when groomer is not in use.

2. To raise or lower the groomer loosen hardware (L) on

both ends of the reel and pivot the groomer up or down.

Tighten hardware (L).

3. To return groomer to operating position loosen

hardware (L), and fully pivot groomer down until pin (M)

is at bottom of slot.

NOTE: DO NOT adjust groomer height by loosening

hardware (L) and pivoting groomer assembly. Only use the

groomer height knobs (F and K).

Figure 23

0 - 1/2B

Pivot

Lubrication __________________________________________________________

Lubrication intervals are based on operating from 8 to 10

hours per day, 5 days per week under normal operating

conditions.

All maintenance intervals must be performed more

frequently when operating in extremely dusty conditions.

1. Always clean the grease fitting before and after

lubricating.

2. Lubricate with grease that meets or exceeds NLGI

Grade 2 specifications.

3. Apply grease with a manual grease gun and fill slowly

until pressure is felt. Do not use compressed air guns

to prevent damage to seals.

Grease each of the following points not more than once

a month.

a. Reel Height of Cut Knob (2 Fittings) (N)

b. Groomer bearing housings (2 Fittings) (P)

c. Roller bearings (2 Fittings) (R)

d. Groomer Height Knob (2 Fittings) (S)

4. Apply grease as required to the cover seal to prevent

overheating.

5. For smooth operation of pivot points and other friction

points apply several drops of SAE 30 wt. oil every 40

hours or as required.

Clean and lubricate individual parts and components

as required. Apply Anti seize compound between

groomer plates.

Figure 24

TURF GROOMER

Fixed Head Adapter Kit 67965

Eclipse 118, 122, and 126 Mowers

Serial No. All

> Change from previous revision

TURF GROOMER

Item Part No. Qty. Description Serial Numbers/Notes

67965 1 Fixed Head Groomer Adapter

1 343616 2 • Stud

2 364441 2 • Spacer

3 400196 4 • Screw, 5/16-18 x 2” Hex Head

4 4159385 2 • Spacer, Slide

5 4159406 1 • Mount, Right Side

6 4159411 1 • Mount, Left Side

7 4181482 1 • Adapter, Seal

8 441672 2 • Carriage Bolt, 5/16-18 x 2-1/2”

9 445795 2 • Nut, 5/16-18 Spiralock Flange

10 446136 4 • Lockwasher, 5/16 Heavy

11 446142 1 • Lockwasher, 3/8 Heavy

12 434029 2 • Screw, 1/4-20 x 1” Socket Head

13 365256 1 • Spacer, 7/8 x 13/32”

14 4181442 1 Seal, V-Ring Included with Groomer Kit

15 365256 1 Spacer, 7/8 x 13/32” Included with Groomer Kit

16 365239 1 Key Included with Groomer Kit

17 4118617 1 Pulley Included with Groomer Kit

18 4159385 2 Spacer, Slide Included with Groomer Kit

19 364441 2 Spacer Included with Groomer Kit

20 306866 1 Screw, 3/8-24 x 1-1/4 in. Hex Head Included with Groomer Kit

TURF GROOMER

Groomer Cover and Weights

Serial No. All

> Change from previous revision

TURF GROOMER

Item Part No. Qty. Description Serial Numbers/Notes

4184440 1 Groomer Cover

> 4197540 1 • Seal, Pulley

2 4182941 1 Cover, Pulley

3 434053 2 Screw, #10-24 x 2-1/4” Socket Head

4 446118 4 Lockwasher, #10 Heavy

5 452002 4 Flat Washer, #10

6 434052 2 Screw, #10-24 x 2” Socket Head

7 4257195 1 Weight Used on Eclipse 322, 122F, and 118F

8 400114 1 Screw, 1/4-20 x 1-1/4” Hex Head Used on Eclipse 322, 122F, and 118F

9 446130 1 Lockwasher, 1/4 Heavy Used on Eclipse 322, 122F, and 118F

10 453023 2 Flat Washer, 1/4 Used on Eclipse 322, 122F, and 118F

11 443102 2 Nut, 1/4-20 Hex Used on Eclipse 322, 122F, and 118F

12 4186084 1 Cover, Weight Used on Eclipse 322, 122F, and 118F

13 4186083 1 Weight Used on Eclipse 322, 122F, and 118F

14 434023 2 Screw, 1/4-20 x 1-1/4” Socket Head Used on Eclipse 322, 122F, and 118F

TURF GROOMER

Groomer Assembly

Serial No. All

> Change from previous revision

TURF GROOMER

Item Part No. Qty. Description Serial Numbers/Notes

REF 1 Drive Assembly See Drive and Driven Assembly

2 REF 1 Driven Assembly See Drive and Driven Assembly

3 REF 1 Groomer Blade Assembly See Groomer Blade Assembly

4 REF 1 Groomer Roller See Roller Assembly

5 4157260 4 Nut, 7/8–14 HH. Spec.

> 6 4192282 2 Guide Wheel

7 364441 8 Spacer

8 446136 4 Lockwasher, 5/16 Heavy

9 400184 2 Screw, 5/16-18 x 3/4” Hex Head

10 4182700 1 Link, Belt Tensioner

11 400260 1 Screw, 3/8-16 x 7/8” Hex Head

12 446142 5 Lockwasher, 3/8 Heavy

13 367162 1 Eccentric Nut

14 401220 1 Screw, 3/8-16 x 1-1/2” Hex Head

15 400260 1 Screw, 3/8-16 x 7/8” Hex Head

16 4183661 1 Plate, Bearing Housing

17 4159374 2 Plate, Push

18 364061 2 Bracket, Adjuster

19 444718 2 Locknut, 5/16-18 Center

20 400183 2 Screw, 5/16-18 x 5/8” Hex Head

21 4181441 2 Spacer

22 800438 2 Screw, 3/8-16 x 2” Socket Head

23 4159385 2 Spacer, Slide

24 4159397 2 Spacer

25 445802 2 Nut, 5/16-18 Nylon Insert

26 434049 2 Screw, 5/16-18 x 2” Socket Head

27 441677 2 Carriage Bolt, 5/16-18 x 1-1/2”

28 603620 2 Flat Washer

29 445795 2 Nut, 5/16-18 Spiralock Flange

30 4181442 1 Seal, V-Ring

31 365226 1 Cover Plate

32 365256 1 Spacer, 7/8 x 13/32

33 365239 1 Key

34 434027 2 Screw, 1/4-20 x 1/2” Socket Head Not Used on Eclipse 122F and 118F

35 4118617 1 Pulley

36 365235 1 Belt

37 4156919 2 Knob, Adjustment

38 471219 2 Grease Fitting

39 452006 2 Washer, 5/16

> 40 365409 4 Washer

4160552 1 Frame Template Kit

Only required for reels manufactured

before mid-2007. Not Shown

443102 1 • Nut, 1/4-20 Hex

400112 1 • Screw, 1/4-20 x 1”

TURF GROOMER

Drive and Driven Assembly

Serial No. All

Page is loading ...

Ransomes 67966 67995 67968 67996 67970 67993 67975 67965 Accessories Manual

Brand: Ransomes

Model: 67966 67995 67968 67996 67970 67993 67975 67965

Category: Lawnmowers

Type: Accessories Manual

Download PDF

report

Ransomes 67966 67995 67968 67996 67970 67993 67975 67965 Accessories Manual

Ransomes 67966 67995 67968 67996 67970 67993 67975 67965 Accessories Manual

Related papers

Other documents