Honda 2007 Pilot Installation Instructions Manual

Honda
Brand
Honda
Model
2007 Pilot
Category
Car kits
Type
Installation Instructions Manual

Honda 2007 Pilot Security System

The Honda 2007 Pilot Security System is a comprehensive anti-theft system that helps protect your vehicle from unauthorized access and theft. The system includes a variety of features to deter and prevent theft, including:

  • Panic alarm: This feature triggers a loud alarm to scare away potential thieves and alert others to the attempted theft.
  • Remote keyless entry: This feature allows you to lock and unlock your vehicle's doors and trunk using a remote transmitter.
  • Immobilizer: This feature prevents the engine from starting if the correct key is not used.

Honda 2007 Pilot Security System

The Honda 2007 Pilot Security System is a comprehensive anti-theft system that helps protect your vehicle from unauthorized access and theft. The system includes a variety of features to deter and prevent theft, including:

  • Panic alarm: This feature triggers a loud alarm to scare away potential thieves and alert others to the attempted theft.
  • Remote keyless entry: This feature allows you to lock and unlock your vehicle's doors and trunk using a remote transmitter.
  • Immobilizer: This feature prevents the engine from starting if the correct key is not used.
© 2006 American Honda Motor Co., Inc. - All Rights Reserved. All 33080-33238 (0607) 1 of 7
INSTALLATION
INSTRUCTIONS
Accessory Application Publications No.
Issue Date
08E55-S9V-1A00-91
2007 PILOTSECURITY SYSTEM
PARTS LIST
Security System Kit (sold separately)
P/N 08E51-EP4-101
LED
Push nut
2-pin connector (for LED)
Microphone
Window decal
Accessory user's
Information Manual
Attachment Kit (sold separately)
P/N 08E55-S9V-100A
Security system harness
Control unit bracket
8 Wire ties
Wire tie with connector holder
Holder bracket
2 EPT sealers
Cushion tape
Flange bolt
Security system control unit
Small wire tie
JULY 2006
All 33080-33238
2 of 7 All 33080-33238 (0607) © 2005 American Honda Motor Co., Inc. - All Rights Reserved.
3D08170
T
3D08011
T
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Flat-tip screwdriver
8 mm and 10 mm Combination wrenches
Ratchet
10 mm Socket
Diagonal cutters
Punch
Felt-tip pen
Isopropyl alcohol
Shop towel
Drill
3 mm, 5.5 mm and 8 mm Drill bits
Tape measure
Eye protection (face shield, safety goggles, etc.)
Illustration of Security System installed on the
Vehicle
INSTALLATION
Customer Information: The information in this
installation instruction is intended for use only by
skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
equipment to your vehicle. These procedures
should not be attempted by “do-it-yourselfers.”
1. Make sure you have the anti-theft code for the
radio, then write down the frequencies for the
preset buttons.
2. Disconnect the negative cable from the battery.
3. Remove the driver’s dashboard lower cover (one
self-tapping screw, three clips, and two hooks).
SECURITY
UNIT
MICROPHONE
SECURITY SYSTEM
HARNESS
LED
HOOK
DRIVER’S
DASHBOARD
LOWER COVER
CLIPS (3) SELF-TAPPING
SCREW
RETAINING
TABS (2) SWITCH COVER
4. Remove the switch cover (two retaining tabs).
© 2006 American Honda Motor Co., Inc. - All Rights Reserved. All 33080-33238 (0607) 3 of 7
3D08190
T
4N17020Y
3D08020
T
STEERING
HANGER
BEAM
BOLT
TPMS UNIT
SECURITY SYSTEM
CONTROL UNIT
CONTROL UNIT
BRACKET
CONNECTOR AREA
(Do not push here.)
SELF-
TAPPING
WASHER-
SCREW
LOWER
STEERING
COLUMN
COVER
Push
RETAINING
TABS (7)
SHIFT LEVER
“N” “1”
STEERING
WHEEL
TILT
LEVER
UPPER STEERING
COLUMN COVER
SHIFT LOCK
RELEASE HOLE
IGNITION
KEY
SCREW
5. Lower the steering wheel using the tilt lever, then
remove the upper and lower steering column
covers (two washer-self-tapping screws and one
screw).
• Carefully push in the seven retaining tabs to
release the tabs and remove the lower
steering column cover.
• Insert the ignition key in the shift lock release
hole, and move the shift lever to the “N”
position while pressing down on the key.
• Remove the key, then lift the upper steering
column cover. Pull the cover out toward you,
and remove it by lowering the shift lever to the
“1” position.
6. Remove the bolt from the steering hanger beam
and remove the TPMS unit.
7. Slide the control unit bracket onto the security
system control unit. Do not push on the connector
area.
4 of 7 All 33080-33238 (0607) © 2005 American Honda Motor Co., Inc. - All Rights Reserved.
4N17030
Y
4N17040
Y
CONTROL
UNIT
BRACKET
FLANGE BOLT
VEHICLE
BRACKET
HOLE
FLANGE
BOLT
CONTROL
UNIT
BRACKET
TAB
STEERING
SHAFT
VEHICLE BRACKET
3D08062
T
BLUE TAPE VEHICLE
HARNESS
SECURITY
SYSTEM
HARNESS
SECURITY
SYSTEM
HARNESS
14-PIN
CONNECTOR
VEHICLE
14-PIN
CONNECTOR
STEERING
HANGER BEAM
3D08073
T
VEHICLE
HARNESS
SECURITY
SYSTEM
HARNESS
WIRE TIE
8. Loosely install the flange bolt to the vehicle
bracket at the right side of the steering shaft.
9. Insert the control unit bracket onto the flange bolt.
Align the tab from control unit bracket to the
corner of the vehicle bracket, and tighten the
flange bolt.
10. Install the two wire ties with clip from the security
system harness to the holes in the steering
hanger beam.
11. Plug the security system harness 22-pin
connector into the security unit.
12. Reinstall the TPMS unit removed in step 6.
13. Below the steering hanger beam, locate the 14-pin
connector blue-taped to the vehicle harness, and
remove the blue tape to free the connector. Plug
the security system harness 14-pin connector into
the 14-pin connector you just freed.
14. Secure the security system harness to the
vehicle harness with the two wire ties.
Installing the LED
CORNER
SECURITY
SYSTEM
HARNESS
22-PIN
CONNECTOR
SECURITY
SYSTEM
HARNESS
SECURITY
SYSTEM
CONTROL
UNIT
STEERING
HANGER BEAM
WIRE TIES
WITH CLIP
© 2006 American Honda Motor Co., Inc. - All Rights Reserved. All 33080-33238 (0607) 5 of 7
3D08111
T
3D08160
T
3D08080T
Insert. Lock.
WHITE WIRE
RED WIRE
2-PIN
CONNECTOR
CUSHION
TAPE
LED
HARNESS
UPPER STEERING
COLUMN COVER
UPPER STEERING
COLUMN COVER
5.5 mm BIT
MARK
30 mm
CENTER LINE
PUNCH
DRILL
FELT-TIP
PEN
LED
HARNESS
UPPER STEERING
COLUMN COVER
WIRE TIE
UPPER STEERING
COLUMN COVER
LED
LED
PUSH NUT
(Note the installation direction.)
15. On the inside of the upper steering column cover,
measure and mark the upper steering column
cover.
16. While wearing eye protection, center-punch the
mark; then drill a 5.5 mm hole through the upper
steering column cover. Remove all burrs with a
round file.
17. Route the terminal ends of the LED through the
hole you just drilled, and secure the LED with the
push nut. Install the push nut securely.
18. Using isopropyl alcohol, thoroughly clean the
back of the upper steering column cover in the
area shown. Secure the LED harness to the upper
steering column cover with a cushion tape.
19. Get the 2-pin connector included in the kit. Firmly
push the LED terminals into the 2-pin connector
until they click into position, then lower the lock.
NOTE:
It is important to insert the red and white wires as
shown for the LED to fanction.
20. Reinstall the upper steering column cover, then
secure the LED harness to the vehicle harness
with the wire tie.
21. Route the security system harness 2-pin
6 of 7 All 33080-33238 (0607) © 2005 American Honda Motor Co., Inc. - All Rights Reserved.
3D08101
3D08092
T
CENTER LINE 3 mm
8 mm BIT
SWITCH
COVER
FELT-TIP PEN
DRILL
PUNCH
MICROPHONE
JACK
MICROPHONE SWITCH COVER
SWITCH COVER
3D08122
T
HOLDER BRACKET WIRE TIE WITH
CONNECTOR HOLDER
LED HARNESS
2-PIN CONNECTOR
VEHICLE
HARNESS
SECURITY SYSTEM
HARNESS
WIRE TIE
SECURITY
SYSTEM
HARNESS
2-PIN
CONNECTOR
connector along the vehicle harness and plug it to
the LED harness 2-pin connector.
22. Insert the holder bracket onto the LED harness
2-pin connector and insert the wire tie with
connector holder into the holder bracket.
23. Secure the LED harness and the security system
harness to the vehicle harness with the wire tie
with connector holder and the wire tie.
24. Reinstall the lower steering column cover.
Installing the Microphone
25. Measure and mark the center of the switch cover
removed in step 4.
26. While wearing eye protection, center-punch the
mark; then drill an 8 mm hole through the center-
punched mark. First drill a pilot hole with a 3 mm
bit, then finish with an 8 mm bit. Remove all burrs.
27. Route the microphone jack through the hole in the
switch cover and seat the microphone in the
switch cover.
28. Cut two EPT sealers in half. Wrap three of the
© 2006 American Honda Motor Co., Inc. - All Rights Reserved. All 33080-33238 (0607) 7 of 7
4N17050
Y
3D08182
T
EPT SEAL 100 mm
1/2 EPT SEALER
MICROPHONE
HARNESS 50 mm
SWITCH
COVER
MICROPHONE
SECURITY
SYSTEM
CONTROL
UNIT
MICROPHONE JACK
INSTRUMENT
PANEL
TAB
SMALL
WIRE TIE MICROPHONE
HARNESS
3D08154
T
SECURITY
SYSTEM
HARNESS WIRE TIE
MICROPHONE
HARNESS
INSTRUMENT
PANEL
<Side view>
WIRE TIE
WIRE TIE
VEHICLE
HARNESS
MICROPHONE
HARNESS
Make loops in
the microphone
harness.
pieces around the microphone harness at the
locations shown.
29. Secure the microphone harness to the switch
cover with the small wire tie. Reinstall the switch
cover.
• Position the tab from the wire tie in the center
of the switch cover.
30. Route the microphone jack along the instrument
panel, and plug it to the security system control
unit.
31. Secure the security system harness to the vehicle
harness with one wire tie.
32. Secure the microphone harness to the security
system harness with one wire tie so that no
tension is applied to the microphone jack.
33. Loop in the excess microphone harness and
secure the microphone harness to the instrument
panel with two wire ties.
34. Check that all wire harnesses and cables are
routed properly and all connectors are plugged in.
35. Reconnect the negative cable to the battery.
36. Enter the customer’s radio anti-theft code, if
applicable, and reset the radio station presets.
37. Set the clock.
38. Check operation of the security system according
to the Owner’s Manual supplied.
NOTE: Whenever the battery is disconnected, the
driver’s window AUTO function is disabled.
39. Start the engine. Push down on the driver’s
window switch until the window is fully open.
40. Pull up on the driver’s window switch to close the
window completely, then hold the switch for 2
seconds.
41. Lower and raise the driver’s window to check
operation of the driver’s window AUTO function.
1/2 EPT
SEALER
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Honda 2007 Pilot Installation Instructions Manual

Honda
Brand
Honda
Model
2007 Pilot
Category
Car kits
Type
Installation Instructions Manual

Honda 2007 Pilot Security System

The Honda 2007 Pilot Security System is a comprehensive anti-theft system that helps protect your vehicle from unauthorized access and theft. The system includes a variety of features to deter and prevent theft, including:

  • Panic alarm: This feature triggers a loud alarm to scare away potential thieves and alert others to the attempted theft.
  • Remote keyless entry: This feature allows you to lock and unlock your vehicle's doors and trunk using a remote transmitter.
  • Immobilizer: This feature prevents the engine from starting if the correct key is not used.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents