Acura 08E02-S6M-200 Installation Instructions Manual

Brand: Acura

Model: 08E02-S6M-200

Type: Installation Instructions Manual

Acura 08E02-S6M-200 is a hands-free telephone interface specifically designed for the 2004 Acura RSX. It allows you to connect your cellular phone to your car's audio system, enabling you to make and receive calls without taking your hands off the wheel. The kit includes a control unit, microphone, modular jack, earphone hanger clip, and all necessary cables and hardware for installation. With simple installation procedures, you can enjoy the convenience of hands-free calling while on the road.

INSTALLATION

INSTRUCTIONS

Accessory Application Publications No.

Issue Date

OCT 2003

08E02-S6M-2000-91

2004 RSX

HANDS-FREE TELEPHONE

INTERFACE

PARTS LIST

Harness Kit (sold separately):

P/N 08E02-S6M-200

Telephone harness

Control unit bracket

Modular jack

7 Wire ties

EPT sealer

(Soft cushion tape)

Hands-Free Telephone Kit (sold separately):

P/N 08E00-ED0-200

Control unit

Microphone

Earphone

2 Cushion tapes

Earphone hanger clip

2 Double-sided cushions

(not used)

Owner’s manual

2 Washer-screws,

4 x 10 mm

2 Washer-screws,

3 x 8 mm

Telephone Cable (sold separately):

Telephone cable

(The cable type is dependent upon

the customer’s cellular phone.)

BII 26306

TOOLS AND SUPPLIES REQUIRED

Phillips screwdriver

Stubby Phillips screwdriver

Flat-tip screwdriver

Isopropyl alcohol (Isopropyl alcohol, in a 60/40 with

water)

Shop towel

Diagonal cutters

Illustration of the Hands-free Telephone System

Illustration of the Hands-free Telephone Installed in

the vehicle

3903010T

CELLULAR

PHONE

EARPHONE

HANGER CLIP

AUDIO UNIT

With radio tuner

TELEPHONE

HARNESS

MICROPHONE

CONTROL

UNIT

MODULAR

JACK

EARPHONE

TELEPHONE

CABLE

VEHICLE 20-PIN

CONNECTOR

INSTALLATION

Customer Information: The information in this

installation instruction is intended for use only by

skilled technicians who have the proper tools,

equipment, and training to correctly and safely add

equipment to your vehicle. These procedures

should not be attempted by “do-it-yourselfers.”

1. Make sure you have the anti-theft code for the

radio, then write down the frequencies for the

preset buttons.

2. Disconnect the negative cable from the battery.

3. Inside the vehicle, turn the two knobs

counterclockwise, and remove the driver’s

dashboard lower cover (two retaining tabs and

two hooks).

3903020T

MICROPHONE

VEHICLE 20-PIN

CONNECTOR

TELEPHONE

HARNESS

EARPHONE

CONTROL

UNIT

MODULAR

JACK

AUDIO UNIT

With radio

tuner

CELLULAR

PHONE

DRIVER’S

DASHBOARD

LOWER COVER

KNOB

RETAINING

TABS (2)

HOOKS (2)

3903030T

GLOVE BOX

UNDER COVER

HOOK

HOLDER

CLIPS (3)

4. Remove the (two self-tapping screws, one screw,

and the steering column upper cover six retaining

tabs).

5. Pull the center lower cover toward you to release

the one retaining tab and six clips.

6. Unplug the vehicle connector from the accessory

socket, and remove the center lower cover.

7. Using a stubby Phillips screwdriver, remove the

two bolts. Pull the center panel out toward you to

release four clips. Unplug the vehicle connectors

and antenna lead.

8. Remove the glove box under cover (three clips

and release the hook from the holder).

STEERING

COLUMN

LOWER

COVER

SCREW

SELF-TAPPING

SCREW

STEERING COLUMN

UPPER COVER

RETAINING TABS (6)

Push in.

CENTER LOWER

COVER

CLIPS (6)

RETAINING TAB

ACCESSORY

SOCKET

VEHICLE

CONNECTOR

CLIPS (4)

CENTER PANEL

BOLT

VEHICLE

CONNECTOR

ANTENNA

LEAD

CLIPS (4)

3903040T

STOPPER

RETAINING

TAB

Pull down

all the way.

GLOVE

BOX

BOLT

9. Open the glove box. Squeeze the retaining tabs,

and remove the stoppers. Close the glove box.

Remove the glove box by removing the two bolts.

Installing the Microphone Cord

10. Using isopropyl alcohol on a shop towel, clean the

bonding surface of the steering column upper

cover where the microphone will attach.

11. Remove the adhesive backing from the

microphone and attach it to front surface of the

cover, with the microphone cord in the center of

the meter panel.

12. Using isopropyl alcohol, clean the area where EPT

sealers will attach. Using scissors, cut one EPT

sealer into three pieces. Route the microphone

cord on the bottom face of the meter panel and

attach the cord with the EPT sealers in the areas

as shown.

3903050T

MICROPHONE

ADHESIVE

BACKING

Clean with

isopropyl

alcohol.

STEERING

COLUMN UPPER

COVER

CENTER

3903060T

EPT SEAL

Clean with

isopropyl alcohol.

BACK OF THE

STEERING COLUMN

UPPER COVER

Cut Cut

3903091T

VEHICLE

CORRUGATE

HARNESS

Route the

harness

toward you.

HAZARD SWITCH

HARNESS

VEHICLE 20-PIN

HARNESS with

13. Place the steering column upper cover on the

steering column, and route the microphone cord

toward the audio unit opening. Secure the

microphone cord to the vehicle harness with two

wire ties.

14. Route the microphone cord toward the glove box

opening.

Installing the Telephone Harness

17. Get a telephone harness from the kit.

• If equipped with a Bose amplifier, remove the

tape from the 1-pin connector of the telephone

harness, and plug it to the other 1-pin

connector of the telephone harness attached

with tape. Without a bose amplifier, do not

plug-in.

19. Route the vehicle 20-pin harness behind the

vehicle corrugate harness and hazard switch

harness, and pull it out toward you.

3903070T

VEHICLE

HARNESS

MICROPHONE CORD

WIRE TIE

STEERING

COLUMN UPPER

COVER

3903081T

HALF

OF EPT

SEALER

MICROPHONE

CORD

GLOVE

BOX

OPENING

VEHICLE HARNESS

WIRE TIE

LEFT RADIO

BRACKET

VEHICLE

HARNESS

WIRE TIE

Cut

EPT SEAL

RELAY

3903100T

TELEPHONE

HARNESS

1-PIN

CONNECTOR

TAPE (Remove.)

With Bose

amplifier only.

1-PIN

CONNECTOR

15. Using scissors, cut one EPT sealer in half

horizontally. Wrap the halves of EPT sealer

around the microphone cord where the left radio

bracket and vehicle relay will contact.

16. Secure the microphone cord to the vehicle

harness with two wire ties.

3903131T

SELF-TAPPING

SCREW

LAMP

HARNESS

CONNECTOR

GLOVE BOX

LAMP CASE

19. Plug the telephone harness 20-pin connector into

the vehicle 20-pin connector.

Installing the Control Unit

22. Remove the glove box lamp case (two self-

tapping screws and unplug the lamp harness

connector).

23. Install the control unit to the control unit bracket

with two 4 x 10 mm washer-screws.

3903111T

VEHICLE 20-PIN

HARNESS

Plug-in

TELEPHONE

HARNESS

14-PIN

CONNECTOR

MICROPHONE

CORD

3903121T

AIR DUCT

20-PIN

CONNECTOR

GLOVE BOX

OPENING

14-PIN

CONNECTOR OF

THE TELEPHONE

HARNESS

MICROPHONE

CORD

3903141T

CONTROL

UNIT

4 x 10 mm

WASHER-

SCREWS (2)

CONTROL UNIT

BRACKET

3 x 8 mm

WASHER-

SCREW

MODULAR

JACK

ADHESIVE

BACKING

21. Route the 20-pin connectors onto the air duct

hose. Pull the telephone harness 14-pin

connector from the glove box opening while

moving the 20-pin connector into the air duct.

20. Route the telephone harness 14-pin connector

along the microphone cord and toward the glove

box opening.

24. Remove the adhesive backing from the modular

jack. Install the modular jack to the control unit

with two 3 x 8 mm washer-screws. Insert the clips

in the wire ties of the modular cable to the holes

in the control unit bracket, and the connector of

the modular jack to the control unit.

25. Inside the glove box opening, plug the telephone

harness 14-pin connector and microphone jack

into the control unit.

28. Install the control unit bracket and glove box lamp

case with two self-tapping screws removed in

step 22. Align the pin with the hole of the control

unit bracket.

3903161T

CONTROL UNIT

BRACKET

CUSHION

TAPE

HOLE

LAMP

HARNESS

CONNECTOR

SELF-TAPPING

SCREW (reused)

GLOVE BOX

LAMP CASE

CONTROL

UNIT

BRACKET

FRONT

3903171T

TELEPHONE HARNESS

20-PIN CONNECTOR

WIRE TIE

MICROPHONE CORD

(Bundle up.)

VEHICLE 20-PIN

HARNESS

TELEPHONE

HARNESS

WIRE TIE

HAZARD

SWITCH

HARNESS

3903152T

GLOVE BOX

OPENING

MICROPHONE

JACK

CLIP

CONTROL

UNIT

BRACKET

WIRE

TIE

WIRE TIE WITH

CLIP OF THE

TELEPHONE

HARNESS

CONTROL

UNIT

BRACKET

CONTROL

UNIT

CONTROL UNIT

BRACKET

CONTROL

UNIT

TELEPHONE

HARNESS

14-PIN

CONNECTOR

26. Insert the clip of the wire tie in the telephone

harness to the hole in the control unit bracket.

27. Secure the microphone cord to the telephone

harness with one wire tie in the area shown (near

the wire tie with clip of the telephone harness).

30. Inside the audio unit opening, secure the vehicle

20-pin harness and microphone cord to the

hazard switch harness with one wire tie in the

area shown.

29. Plug the lamp harness connector to the lamp

case, and attach the lamp harness on the bracket

with one cushion tape.

31. Bundle up excess length of the microphone cord,

and secure it to vehicle harness with corrugate

tube.

3903190T

MODULAR

JACK

CELLULAR

PHONE

TELEPHONE

CABLE

EARPHONE

HANGER

CLIP

3903180T

Clean with

isopropyl alcohol.

ADHESIVE

BACKING

EARPHONE

HANGER CLIP

STOPPER

15 mm

3903200T

AUDIO UNIT

TELEPHONE

HARNESS

20-PIN

CONNECTOR

ANTENNA

LEAD

ANTENNA

LEAD

TELEPHONE HARNESS

20-PIN CONNECTOR

Installing the Telephone Cable and Earphone

32. Reinstall the glove box.

33. Using isopropyl alcohol on a shop towel, clean the

bonding surface of the glove box. Remove the

adhesive backing from the earphone hanger clip,

and attach the earphone hanger clip to the glove

box in the area as shown.

34. Plug the telephone cable connector into the

modular cable connector. Plug the telephone

cable connector into the cellular phone.

Installing the Audio Unit

37. Plug the telephone harness 20-pin connector into

the audio unit (There are two types). Reinstall the

audio unit.

38. Check that all wire harnesses are routed properly

and all connectors are plugged in.

39. Reinstall all removed parts.

40. Reconnect the negative cable to the battery.

NOTE: Whenever the battery is disconnected, the

driver’s window AUTO function is disabled.

41. Start engine. Push down fully on the driver’s

window switch until the window is fully open.

42. Pull up fully on the driver's window switch to close

the window completely, then hold the switch for

two seconds.

43. Test the window AUTO function.

35. Plug the earphone jack into the modular jack.

36. Place the earphone on the earphone hanger clip.

Acura 08E02-S6M-200 Installation Instructions Manual

Acura 08E02-S6M-200 Installation Instructions Manual

Acura 08E02-S6M-200 Installation Instructions Manual

Related papers

Other documents