2. Alphalite
  3. LVT-4L-8A Linear LED Vapor Tight

Alphalite LVT-4L-8A Linear LED Vapor Tight User manual

  • Hello! I've reviewed the installation instructions for the Alphalite LED Vapor Tight, specifically models LVT-4L(35/25/18S2)/8A and LVT-4H(64/56/46S2)/8A. This document provides essential steps for safe and correct installation, covering various mounting methods and wiring diagrams. I'm ready to help with any questions you might have about these luminaires.
  • Who should install the LED Vapor Tight?
    Is this luminaire suitable for wet locations?
    What should I do before installation?
10715 Springdale Ave, Ste 4, Santa Fe Springs, CA 90670 l Tel: 1-888-287-9228 l Fax: 1-888-258-9183 l E-mail: [email protected]
Installation Instructions
Alphalite Linear LED Vapor Tight
Installation guide valid for the following models:
LVT-4L(35/25/18S2)/8A
LVT-4H(64/56/46S2)/8A
WARNING
RISK OF FIRE OR ELECTRIC SHOCK
The LED Vapor Tight must be installed by a qualied electrician in accordance with applicable
federal, state, and local laws and codes. Installation requires knowledge of luminaire electrical
systems and installer should be familiar with the operation of this product. If not qualied, do not
attempt installation; contact a qualied electrician. Manufacturer assumes no responsibility for the
improper installation of this luminaire.
Before installing, servicing, or performing routine maintenance upon this equipment, follow these
general precautions.
WARNING
To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp
objects. When installing this kit, drilling may damage luminaire wiring and electrical parts. Check for
wiring and components in enclosure before drilling.
Do not make or alter any open holes in an enclosure of wiring or electrical components during kit
installation.
WARNING
RISK OF PERSONAL INJURY
Wear gloves or proper handling protection to prevent cuts or abrasions when handling and
maintaining this product. This equipment may have sharp edges.
WARNING
RISK OF PERSONAL INJURY, FIRE OR ELECTRIC SHOCK
Turn OFF power before installation.
Contact manufacturer with any questions or concerns regarding installation of this luminaire.
NOTICE: Green ground screw provided in proper location. Do not relocate.
NOTICE: Minimum 90o supple conductors
NOTICE: Specications and dimensions subject to change without notice.
NOTICE: Suitable for wet location.
1
10715 Springdale Ave, Ste 4, Santa Fe Springs, CA 90670 l Tel: 1-888-287-9228 l Fax: 1-888-258-9183 l E-mail: [email protected] 2
Installation Instructions
Surface Mounting
Installation Instruction
If you have an interest in this product,please feel free to contact the email:[email protected]
If you have an interest in the other product,please visit the web www.designlights.org/qpl.
Search by Keyword : ever-tie
Always turn off the power supply from main circuit breaker first!
A: Surface Mounting
1.Locate drill holes for mounting brackets. Use hardware
NSTRUCTIONS:
found in hardware kit. Mount bracket to surface.
2.Secure mounting clips to housing recesses by firmly
pressing them into place until both sides of the clip are
3.Release latches by pulling top of latch away from
secured.
4.Without touching LED boards,detach LED tray and
lens from fixture.
housing.
5.Connect power to driver as shown in the figure.
(the flexible cord supplied by others)
10715 Springdale Ave, Ste 4, Santa Fe Springs, CA 90670 l Tel: 1-888-287-9228 l Fax: 1-888-258-9183 l E-mail: [email protected]
Installation Instruction
If you have an interest in this product,please feel free to contact the email:[email protected]
If you have an interest in the other product,please visit the web www.designlights.org/qpl.
Search by Keyword : ever-tie
5.Without touching LED boards,detach LED tray and
lens from fixture.
6.Connect power to driver as shown in the figure.
(the flexible cord supplied by others)
7.Follow general wiring Diagram on Figure for reference.
Make sure the power supply is disconnected before
9.Secure lens to housing with lens latches.
installing.
step 5.
8.Reattach LED tray and lens to fixture by reversing
Installation Instructions
Surface Mounting
10715 Springdale Ave, Ste 4, Santa Fe Springs, CA 90670 l Tel: 1-888-287-9228 l Fax: 1-888-258-9183 l E-mail: [email protected]
Installation Instructions
Chain Suspended Mounting
Installation Instruction
If you have an interest in this product,please feel free to contact the email:[email protected]
If you have an interest in the other product,please visit the web www.designlights.org/qpl.
Search by Keyword : ever-tie
Chain Suspended Mounting
B:
ends of the V-bracket apart and then inserting the legs
1.Attach V-bracket to each mounting clip by spreading the
into the holes in the side of the mounting clips.
2.Secure mounting clips to housing recesses by firmly
pressing them into place until both sides of the clip are
secured.Hang fixture from customer supplied chain
using V-brackets.
3.Hang fixture from customer supplied chain using
V-brackets.
4.Release latches by pulling top of latch away from
housing.
10715 Springdale Ave, Ste 4, Santa Fe Springs, CA 90670 l Tel: 1-888-287-9228 l Fax: 1-888-258-9183 l E-mail: [email protected]
Installation Instructions
Pendant mount
Installation Instruction
If you have an interest in this product,please feel free to contact the email:[email protected]
If you have an interest in the other product,please visit the web www.designlights.org/qpl.
Search by Keyword : ever-tie
6.Follow general wiring Diagram on Figure for reference.
Make sure the power supply is disconnected before
7.Reattach LED tray and lens to fixture by reversing
step 4.
installing.
Secure lens to housing with lens latches.
8. Wiring Diagram:
120-277v
Black(Line)
White(Neutral)
Green(Grd)
Purple(Dim+)
Grey(Dim-)
Blue(-)
Red(+)
Dimming wire
to 0-10v IEC
compliant control
Lead wire to
LED load
10715 Springdale Ave, Ste 4, Santa Fe Springs, CA 90670 l Tel: 1-888-287-9228 l Fax: 1-888-258-9183 l E-mail: [email protected]
Installation Instruction
If you have an interest in this product,please feel free to contact the email:[email protected]
If you have an interest in the other product,please visit the web www.designlights.org/qpl.
Search by Keyword : ever-tie
Boom installation
9.Follow general wiring Diagram on Figure for reference.
Make sure the power supply is disconnected before installing.
10.Reattach LED tray to fixture by reversing step 5.
Secure lens to housing with lens latches.
11.
Installation Instructions
Pendant mount
/