2. Litetronics
  3. LHBC Series
LHBC Series

Litetronics LHBC Series Installation guide

  • Hello! I've reviewed the Installation Instructions for the Litetronics LED Linear High Bay C-Series LHBC Series. This document outlines the steps for installing the fixture, including how to set the color temperature and connect wiring. It also covers the installation of additional components such as sensors. I'm ready to answer any questions you have about this product.
  • What is included in the box?
    What tools are needed for installation?
    How do I set the color temperature?
    Can I use a sensor with this fixture?
LED Linear High Bay (C-Series)
Installation Instructions
Ordering Code: LHBC Series
SAFETY INSTRUCTIONS AND WARNINGS
WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE OBSERVED
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
• Risk of fire or electric shock. Linear High Bay or Low Bay luminaire installation requires knowledge of luminaires electrical
systems. If not qualified, do not attempt installation. Contact a qualified electrician.
• Be certain electrical power is OFF before and during installation and maintenance.
• Linear High Bay or Low Bay luminaire must be connected to a wiring system with an equipment – grounding conductor.
• Make sure the supply voltage is same as the rated luminaire voltage
• Only those open holes indicated in the photographs and/or drawings may be made or altered as a result of this fixture
installation. Do not leave any other open holes in an enclosure of wiring or electrical components.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or sharp objects.
• No user serviceable parts inside of Linear High Bay or Low Bay Lumiaire.
WHAT COMES IN THE BOX
LED Linear High Bay with 6’ input wire
2 V-hooks and chains
Installation instructions
TOOLS NEEDED
Wire Stripper
Wire Cutter
Phillips Screwdriver
SUSPENDING THE FIXTURE FROM A BEAM/RAFTER (FIGURE A)
1. Suspend the fixture by securing the v-hooks to the interior structure.
2. Install the chains to the provided v-hooks, then mount the hangers to the top side of the
fixture (as shown in Figure A).
3. Make wiring connections based on the instructions and diagrams below.
INSTALLING THE PLUGGABLE SENSOR (FIGURE B)
1. Unscrew and remove sensor port plug
2. Plug sensor into port and screw to tighten (sensor sold separately)
INSTALLATION INSTRUCTIONS
Before starting installation, turn off power at circuit breaker.
SETTING THE COLOR TEMPERATURE
1. Before installing the fixture, find the CCT slide switch on the side of the driver and select
the preferred color temperature.
CCT settings: 4000K | 5000K
LED Linear High Bay
Black/Brown
White/Blue
/Pink
WIRING DIAGRAM
120V & 277V
*For 240V, follow 480V wiring instructions
INSTALLATION INSTRUCTIONS
Installation Instruction
If you have an interest in this product,please feel free to contact the email:[email protected]
If you have an interest in the other product,please visit the web www.designlights.org/qpl.
Search by Keyword : ever-tie
C:
A:
Chain Kit
B:
Cable Kit
flexible metallic conduit
flexible metallic conduit
Surface Mounting
Installation Instruction
If you have an interest in this product,please feel free to contact the email:[email protected]
If you have an interest in the other product,please visit the web www.designlights.org/qpl.
Search by Keyword : ever-tie
C:
A:
Chain Kit
B:
Cable Kit
flexible metallic conduit
flexible metallic conduit
Surface Mounting
FIGURE A - FIXTURE INSTALLATION
FIGURE B - SENSOR INSTALLATION
Installation Instruction
If you have an interest in this product,please feel free to contact the email:[email protected]
If you have an interest in the other product,please visit the web www.designlights.org/qpl.
Search by Keyword : ever-tie
Additional Accessories
Microwave Motion Sensor
2.Remove base cover.
1.The installation effect of the whole lamp.
4.Install the sensor.
3.Exposed sensor base.
Fast installation
6.The installation is completed.
5.Turn the sensor clockwise.
General Wiring Diagram
Sensor
12VDC
-
Brown
Dim to off dirver
LED Light Source
Red
Blue
Purple
Gray
Yellow
LED+
LED
-
DIM+
DIM
-
12VDC+
L
N
Black
White
Installation Instruction
If you have an interest in this product,please feel free to contact the email:[email protected]
If you have an interest in the other product,please visit the web www.designlights.org/qpl.
Search by Keyword : ever-tie
Additional Accessories
Microwave Motion Sensor
2.Remove base cover.
1.The installation effect of the whole lamp.
4.Install the sensor.
3.Exposed sensor base.
Fast installation
6.The installation is completed.
5.Turn the sensor clockwise.
General Wiring Diagram
Sensor
12VDC
-
Brown
Dim to off dirver
LED Light Source
Red
Blue
Purple
Gray
Yellow
LED+
LED
-
DIM+
DIM
-
12VDC+
L
N
Black
White
Installation Instruction
If you have an interest in this product,please feel free to contact the email:[email protected]
If you have an interest in the other product,please visit the web www.designlights.org/qpl.
Search by Keyword : ever-tie
Additional Accessories
Microwave Motion Sensor
2.Remove base cover.
1.The installation effect of the whole lamp.
4.Install the sensor.
3.Exposed sensor base.
Fast installation
6.The installation is completed.
5.Turn the sensor clockwise.
General Wiring Diagram
Sensor
12VDC
-
Brown
Dim to off dirver
LED Light Source
Red
Blue
Purple
Gray
Yellow
LED+
LED
-
DIM+
DIM
-
12VDC+
L
N
Black
White
7/14/22 - V1.2
The information and product specifications contained in these
instructions are based upon data believed to be accurate at the time
of printing. This information is subject to change without notice and
without incurring liability. If you have questions regarding specific
product details, please contact us at 800-860-3392 or via email at
[email protected].
To check for an updated version of these instructions,
please visit www.litetronics.com.
WWW.LITETRONICS.COM
CustomerService@Litetronics.com or 1-800-860-3392
6969 W. 73rd Street
Bedford Park, IL 60638
Thank you for choosing
/