Krone EasyCollect 6000 FP Operating instructions

Brand: Krone

Model: EasyCollect 6000 FP

Type: Operating instructions

This manual is also suitable for

BA EasyCollect 6000 FP

O r i g i n a l o p e r a t i n g i n s t r u c t i o n s

Maize header

EasyCollect 6000 FP

(from serial no.: 822 000)

Order no.: 150 000 055 04 us

09.05.2011

Foreword

Pos: 1/ BA/Vorwort/Sehr ge ehrter Kunde @ 0\mod_11956263 00326_78.docx @ 905 @ @ 1

Dear customer,

You have now received the operating instructions for the KRONE

product which you have purchased.

These operating instructions contain important information for the

proper use and safe operation of the machine.

If these operating instructions should become wholly or partially

unusable, you can obtain replacement operating instructions for

your machine by stating the number given overleaf.

Pos: 2/ BA/-------- -------Seitenumbruch------- --------- @ 0\mod_1196175311 226_0.docx @ 4165 @ @ 1

Foreword

Pos: 3/ BA/Inhaltsverzeich nis Sprachenneutral @ 10\mod_ 1221574899104_0.d ocx@ 1 35495 @ @ 1

1 Foreword .................................................................................................................................................7

2 Introduction.............................................................................................................................................8

2.1 Purpose of Use.................................................................................................................................. 8

2.2 Validity ............................................................................................................................................... 8

2.2.1 Contact........................................................................................................................................... 8

2.3 Identification Plate ............................................................................................................................. 9

2.4 Information Required for Questions and Orders................................................................................ 9

2.5 Intended Use ................................................................................................................................... 10

2.6 Technical data ................................................................................................................................. 10

2.6.1 Ballast / forage harvester............................................................................................................. 10

2.7 Machine overview............................................................................................................................ 11

3 Safety.....................................................................................................................................................13

3.1 Identifying Symbols in the Operating Instructions ........................................................................... 13

3.2 Identification of the hazard warnings............................................................................................... 13

3.2.1 Personnel Qualification and Training........................................................................................... 14

3.2.2 Dangers in Case of Non-compliance with the Safety Instructions............................................... 14

3.2.3 Safety-conscious work practices ................................................................................................. 14

3.3 Safety Instructions and Accident Prevention Regulations............................................................... 15

3.4 Attached devices ............................................................................................................................. 16

3.5 PTO Operation................................................................................................................................. 17

3.6 Hydraulic system ............................................................................................................................. 18

3.7 Maintenance .................................................................................................................................... 19

3.8 Unauthorised Conversion/Modification and Spare Parts Production .............................................. 20

3.9 Inadmissible Modes of Operation.................................................................................................... 20

3.10 Introduction...................................................................................................................................... 21

3.11 Safety Instructions on the Machine ................................................................................................. 21

3.12 Position of the Adhesive Safety Stickers on the Machine ............................................................... 22

3.12.1 Re-Ordering the Adhesive Safety and Information Labels...................................................... 24

3.12.2 Affixing the Adhesive Safety and Information Labels.............................................................. 24

3.12.3 Contact for KRONE NORTHAMERICA................................................................................... 24

4 Start-up -CLAAS ...................................................................................................................................25

4.1 Stop points....................................................................................................................................... 26

4.2 Storage ............................................................................................................................................ 26

4.3 Attachment to the CLAAS forage harvester .................................................................................... 27

4.4 Purpose of Use................................................................................................................................ 27

4.5 Preparations on the forage harvester (type 491, type 492)............................................................. 27

4.6 Preparations on the forage harvester (type 493, type 494)............................................................. 28

4.6.1 Preparations on the EasyCollect ................................................................................................. 30

4.7 Coupling........................................................................................................................................... 31

4.7.1 Type 491, type 492...................................................................................................................... 31

4.7.2 Type 493, type 494...................................................................................................................... 33

4.7.3 Connecting the hydraulic lines..................................................................................................... 35

4.8 Detaching the machine.................................................................................................................... 37

4.8.1 Type 491, type 492...................................................................................................................... 39

4.8.2 Type 493, type 494...................................................................................................................... 40

5 Start-up – John Deere..........................................................................................................................41

5.1 Friction Clutch.................................................................................................................................. 41

5.2 Stop points....................................................................................................................................... 42

Foreword

5.3 Storage ............................................................................................................................................ 42

5.4 Mounting on John Deere forage harvesters.................................................................................... 43

5.5 Purpose of Use................................................................................................................................ 43

5.6 Preparations on Forage Harvester .................................................................................................. 43

5.6.1 Preparations on the EasyCollect ................................................................................................. 44

5.7 Coupling........................................................................................................................................... 45

5.7.1 Connecting the hydraulic lines..................................................................................................... 48

5.8 Detaching the machine.................................................................................................................... 50

6 Start-up - New Holland.........................................................................................................................53

6.1 Friction Clutch.................................................................................................................................. 54

6.2 Stop points....................................................................................................................................... 55

6.3 Storage ............................................................................................................................................ 55

6.4 Mounting on New Holland forage harvesters .................................................................................. 56

6.5 Purpose of Use................................................................................................................................ 56

6.6 Preparations on Forage Harvester .................................................................................................. 56

6.6.1 Series FX (38, 48, 58, 40, 50, 60)................................................................................................ 56

6.7 Preparations on Forage Harvester .................................................................................................. 56

6.7.1 Series FR 90................................................................................................................................ 56

6.7.2 Preparations on the EasyCollect ................................................................................................. 57

6.8 Coupling........................................................................................................................................... 58

6.8.1 Connecting the hydraulic lines..................................................................................................... 63

6.9 Detaching the machine.................................................................................................................... 66

7 Driving and Transport..........................................................................................................................69

8 Operation...............................................................................................................................................71

8.1 From transport into working position ............................................................................................... 71

8.1.1 Removing the protective cover.................................................................................................... 71

8.2 Using the Machine for Work ............................................................................................................ 72

8.2.1 Using the maize header............................................................................................................... 73

8.3 Switching from working position to transport position ..................................................................... 74

8.3.1 Swinging up the maize header .................................................................................................... 74

8.3.2 Parking supports in transport position on the right/left ................................................................ 75

8.3.3 Installing guard on the right/left.................................................................................................... 75

8.3.4 Connecting indicators and position lights on the right/left........................................................... 76

8.3.5 Installing the front guard .............................................................................................................. 76

9 Settings .................................................................................................................................................77

9.1 Adjusting skids................................................................................................................................. 78

9.2 Adjusting the plant dividers.............................................................................................................. 78

9.3 Adjusting the angle of inclination of the maize header (CLAAS)..................................................... 79

9.4 Adjusting the angle of inclination of the maize header (John Deere).............................................. 80

9.5 Adjusting the angle of inclination of the maize header (New Holland)............................................ 81

9.5.1 Type FX (38,48,58)...................................................................................................................... 81

9.6 Block pendulum frame..................................................................................................................... 82

9.7 Central adjustment of the EasyCollect to the forage harvester for transport .................................. 82

9.8 Adjustment of the compensation springs......................................................................................... 83

9.9 Change-over gearbox...................................................................................................................... 84

9.9.1 Moving the PTO shafts on the change-over gearbox.................................................................. 86

10 Maintenance..........................................................................................................................................88

10.1 Special Safety Instructions .............................................................................................................. 88

Foreword

10.1.1 Test run.................................................................................................................................... 88

10.2 Spare Parts...................................................................................................................................... 88

10.3 Maintenance table ........................................................................................................................... 89

10.4 Tightening Torques.......................................................................................................................... 90

10.5 Tightening Torques (Countersunk Screws)..................................................................................... 91

10.5.1 Tightening torques on the aluminium gearboxes..................................................................... 92

10.6 Filling Quantities and Lubrication Designations for Gearboxes....................................................... 93

10.6.1 Oil Level Check and Oil Change Intervals (Gearboxes).......................................................... 93

10.6.2 Checking the oil level and changing the oil on the spur wheel gearbox.................................. 94

10.6.2.1 John Deere / New Holland............................................................................................... 94

10.6.3 Checking the Oil Level and Changing the Oil on the Main Angular Gearbox ......................... 95

10.6.3.1 Claas................................................................................................................................ 95

10.6.4 Checking the oil level and changing the oil on the transfer gearbox....................................... 96

10.6.5 Checking the oil level and changing the oil on the angular gearbox....................................... 98

10.6.6 Checking the oil level and changing the oil on the dresser gearbox..................................... 100

10.6.7 Checking the Oil Level and Changing the Oil on the Collector Gearbox............................... 101

10.7 Oil level check and oil change on the change-over gearbox......................................................... 102

10.8 Laid maize worm V-belt (right / left)............................................................................................... 103

10.8.1 Optional for John Deere and New Holland............................................................................ 103

10.9 Check the V-belt tension................................................................................................................ 103

10.10 Correcting the V-belt tension..................................................................................................... 105

10.11 Checking and adjusting the collector tension............................................................................ 106

10.12 Adjusting the Scraper ................................................................................................................ 108

10.13 Changing the tips....................................................................................................................... 109

10.14 Adjusting the tips ....................................................................................................................... 110

10.14.1 Adjusting the side tip.............................................................................................................. 110

10.14.2 Adjusting the central tip ......................................................................................................... 111

10.15 Removing and installing insertion finger on the tip holder......................................................... 111

10.16 Blade Changing ......................................................................................................................... 112

10.16.1 Changing bow and step blades ............................................................................................. 112

10.16.2 Changing the cutting blades.................................................................................................. 115

10.16.3 Changing the scraper blade................................................................................................... 116

10.16.4 Changing the dresser segments............................................................................................ 117

10.17 Install the PTO shaft.................................................................................................................. 118

10.18 Friction Clutch............................................................................................................................ 119

10.18.1 John Deere / New Holland..................................................................................................... 119

10.19 Hydraulic hose line(s) ................................................................................................................ 120

10.20 Lubrication ................................................................................................................................. 121

10.20.1 Lubrication Chart ................................................................................................................... 121

10.20.2 PTO shafts............................................................................................................................. 122

10.20.2.1 John Deere .................................................................................................................... 122

10.20.2.2 Claas.............................................................................................................................. 123

10.20.2.3 New Holland................................................................................................................... 123

11 Special equipment..............................................................................................................................124

11.1 Lowering attachment into transport position on parking supports (accessories kit)...................... 124

11.1.1 Scope of the accessories kit.................................................................................................. 124

11.1.2 Attaching the parking supports.............................................................................................. 125

12 Placing in Storage..............................................................................................................................127

Foreword

13 Before the Start of the New Season .................................................................................................128

13.1 Special Safety Instructions ............................................................................................................ 128

13.2 Test run.......................................................................................................................................... 129

14 Index ....................................................................................................................................................130

Pos: 4/ BA/-------- -------Seitenumbruch------- --------- @ 0\mod_1196175311 226_0.docx @ 4165 @ @ 1

Foreword

Pos: 5.1/Ü berschriften/Ü berschriften 1/U-Z/Vorw ort@ 0\ mod_1195627720123 _78.docx @ 982 @ 1@ 1

1 Foreword

Pos: 5.2/ BA/Vorwort/Vorsä tze/Verehrter Kunde Maisge biss @ 15\mod_123263409 2971_78.docx @ 175232 @ @ 1

Dear Customer!

By purchasing the maize header, you have acquired a quality product made by KRONE.

We are grateful for the confidence you have invested in us in buying this machine.

It is important to read the operating instructions very carefully before you start operating the

machine to allow you to use the maize header to its full capacity.

The contents of this manual are laid out in such a way that you should be able to perform any

task by following the instructions step by step. It contains extensive notes and information about

maintenance, how to use the machine safely, secure working methods, special precautionary

measures and available accessories. This information and these instructions are essential,

important and useful for the operational safety, reliability and durability of the maize header.

Pos: 5.3/ BA/Vorwort/Vorsä tze/Weiterer Verlauf Maisge biss @ 15\mod_1232634230 221_78.docx @ 175255 @ @ 1

Note

In the operating instructions which follow the maize header will also be

referred to as the "machine or front attachment".

Pos: 5.4 /BA/Vor wort/Beachten Sie für Maschi ne@ 0\mod_119562 6904076_78.docx @ 9 44@ @ 1

Please note:

The operating instructions are part of your machine.

Only operate this machine after you have been trained to do so and according to these

instructions.

It is essential to observe the safety instructions!

It is also necessary to observe the relevant accident prevention regulations and other generally

recognised regulations concerning safety, occupational health and road traffic.

All information, illustrations and technical data in these operating instructions correspond to the

latest state at the time of publication.

We reserve the right to make design changes at any time and without notification of reasons.

Should you for any reason not be able to use these operating instructions either wholly or

partially, you can receive a replacement set of operating instructions for your machine by

quoting the number supplied overleaf.

We hope that you will be satisfied with your KRONE machine.

Maschinenfabrik Bernard Krone GmbH

Spelle

Pos: 6/ BA/-------- -------Seitenumbruch------- --------- @ 0\mod_1196175311 226_0.docx @ 4165 @ @ 1

Introduction

Pos: 7.1/ BA/Einleitung/Ei nleitung @ 0\mod_11955624 98677_78.docx @ 416 @ 1 @ 1

2 Introduction

These operating instructions contain fundamental instructions. These must be observed in

operation and maintenance. For this reason, these operating instructions must be read by

operating personnel before commissioning and use, and must be available for easy reference.

Follow both the general safety instructions contained in the section on safety and the specific

safety instructions contained in the other sections.

Pos: 7.2/Ü berschriften/Ü berschriften 2/U-Z/Verw endungszweck @ 1\mod_120 1707246738_78.doc x@ 5 4055@ 2 @ 1

2.1 Purpose of Use

Pos: 7.3/ BA/Einleitung/V orsätze/Verwendungsz weck EasyCollect 6000 FP @ 15\mod _1233144092929_7 8.docx@ 1 79520 @ @ 1

The Krone EASYCOLLECT 6000 FP maize header is a harvesting attachment with adapter

frame for attachment to forage harvesters and is used for harvesting maize and other forage

crop with stalks independently of the rows.

Pos: 7.4/ BA/Einleitung/G ültigkeit/Vorsätze/Eas yCollect 6000 FP @ 15\mod_123314 4156304_78.docx @ 1795 43@ 2 @ 1

2.2 Validity

These operating instructions are valid for the maize header

EASYCOLLECT 6000 FP

Pos: 7.5/Ü berschriften/Ü berschriften 3/A-E/Anspr echpartner @ 0\mod_1195569 394286_78.doc x@ 839 @ 3 @ 1

2.2.1 Contact

Pos: 7.6/ Adressen/Adresse Mas chinenfabrik KRONE Spell e@ 0\ mod_1195568531083 _78.docx @ 734@ @1

Maschinenfabrik Bernard Krone GmbH

Heinrich-Krone-Strasse 10

D-48480 Spelle (Germany)

Telephone: + 49 (0) 59 77/935-0 (Head Office)

Fax.: + 49 (0) 59 77/935-339 (Head Office)

Fax.: + 49 (0) 59 77/935-239 (Spare parts - domestic)

Fax.: + 49 (0) 59 77/935-359 (Spare parts - export)

Email: info.ldm@krone.de

Pos: 7.7/ BA/------- --------Seitenumbruch------ ---------- @ 0\mod_1196175311 226_0.docx @ 4165 @ @ 1

Introduction

Pos: 7.8 /Überschrifte n/Überschriften 2/K- O/Kennzeichnung @ 0 \mod_119556462 2099_78.docx @ 496 @ 2 @ 1

2.3 Identification Plate

Pos: 7.9 /BA/Einleitu ng/Kennzeichnung/ Vorsätze/EasyC ollect6 000 (FP)_7500 _9000 @ 15\mod_12 32634850799_78. docx @ 175347 @ @ 1

EC200020

Fig. 1

The machine data are specified on the type plate (1).

Pos: 7.10 /BA/Einleit ung/Kennzeichnung/ Angaben für Anfrag e und Bestellungen_M aschnr. @ 9\mod_1 220507505930_7 8.docx @ 126110 @ 2 @ 1

2.4 Information Required for Questions and Orders

Year

Mach. No.

Type

Note

The entire identification plate represents a legal document and should not be altered or

rendered illegible!

When asking questions concerning the machine or ordering spare parts, be sure to provide type

designation, machine number and the year of manufacture of the relevant machine: To ensure

that these data are always available, we recommend that you enter them in the fields above.

Note

Authentic KRONE spare parts and accessories authorised by the manufacturer help to ensure

safety. The use of spare parts, accessories or additional equipment not manufactured, tested or

approved by KRONE will exclude any liability for consequential damage.

Pos: 7.11 /BA/------ ---------Seitenumbruc h--------- -------@ 0\mo d_11961753112 26_0.docx @ 4165 @ @ 1

Introduction

Pos: 7.12.1 /Überschriften /Überschriften 2/A-E/Besti mmungsgemäßer Ge brauch( alt) @ 0\mod_11964015 45090_78.docx @ 7728 @ 2 @ 1

2.5 Intended Use

Pos: 7.12.2 /BA/Einl eitung/Bestimmungsg emäßer Gebrauc h/Vorsätze/Eas yCollect 6000 FP @ 16\mod _1233144324085 _78.docx @ 179589 @ @ 1

The Krone maize header EASYCOLLECT 6000, (FP) may only be attached to those carrier

vehicles for which the particular adapter frame has been released (observe operating licence of

the carrier vehicle). It is built exclusively for customary use in agricultural work (intended use) -

also refer to Chapter "Purpose of Use".

Pos: 7.12.3 /B A/Einleitung/ Bestimmungsg emäßer Gebra uch/Nicht b estimmungs g emäss (2 012-03-19 1 6:41:15) @ 0\mod_1196401324 340_78.doc x @ 7690 @ @ 1

Any use of the machine for other purposes is deemed not to be in accordance with intended

use. The manufacturer shall not be liable for any resulting damage; the user alone shall bear

the risk.

Operation in accordance with intended use also includes observing the operating, maintenance

and service instructions specified by the manufacturer.

Unauthorised modifications to the machine may affect the properties of the machine or disrupt

proper operation. For this reason, unauthorised modifications shall exclude any liability of the

manufacturer for consequential damage.

Pos: 7.13 /BA/Einleit ung/Technische Dat en/Technische Date n @ 0\mod_1195566 374865_78.doc x@ 594@ 2@ 1

2.6 Technical data

All information, illustrations and technical data in these operating instructions correspond to the

latest state at the time of publication. We reserve the right to make design changes at any time

and without notification of reasons.

Pos: 7.14 /BA/Einleitung/T echnische Daten/Vorsätz e/EasyCollect 6000 FP @ 16\mod_1 233144409491_78.d ocx@ 1 79613 @ @ 1

Type EasyCollect 6000 FP

Length [mm] 2190

Height in working position [mm] 1500

Overall width in working position [mm] 6150

Working width [mm] 6000

Height (folded in) [mm] 3000

Width (folded in) [mm] 2900

Weight [kg] 2800

Power consumption [kW] 40

Drive speed [rpm] 300...700

Max. permitted operating pressure [bar] 200

Hydraulic connections 1xDW*

Electr. connection (lighting) 7-pole

*) DW= Double-action control unit

Pos: 7.15 /BA/Einleitung/ Vorsätze/Ballastierung /F eldhäcksler @ 16\mod_123 3144805382_78.doc x@ 179 638@ 3 @ 1

2.6.1 Ballast / forage harvester

To ensure safe and reliable operation of the carrier vehicle with the Krone maize header

attached, especially in road traffic, the ballast of the machine must be distributed evenly. Follow

the specifications of the certificate of roadworthiness.

Pos: 7.16 /BA/------ ---------Seitenumbruc h--------- -------@ 0\mo d_11961753112 26_0.docx @ 4165 @ @ 1

Introduction

Pos: 7.17 /Überschrift en/Überschriften 2/K-O /Maschinen übersicht @ 0\mod_11 95565731130_78. docx @5 55 @ 2 @ 1

2.7 Machine overview

Pos: 7.18 /WHB/Allgemein es/EasyCollect 6000 FP/E asyCollect FP Voransicht @ 16\mod_12 35645739337_78. docx@ 19 9944@ @ 1

EasyCollect front view

810

WHBEC0080

Fig. 2: EasyCollect front view

(1) Side part (7) Rotating tower

(2) Collector including blades, right (8) Parking support

(3) Tubular bar (9) Cover

(4) Plant divider (10) Insertion finger

(5) Wiper plate (11) Tip

(6) Collector including blades, left

Pos: 7.19 /WHB/Allge meines/EasyColl ect6 000 FP/EasyCollect FP R ückansicht @ 18\ mod_1236932506 097_78.docx @ 20743 6@ @ 1

EasyCollect rear view

6WHBEC0081

Fig. 3: EasyCollect rear view

(1) Outrigger left (6) Outrigger folding cylinder right

(2) Plant divider

(3) Folding cylinder, plant divider (8) Outrigger folding cylinder left

(4) Outrigger right (9) Transfer gearbox left

(5) Transfer gearbox right

Pos: 8/ BA/-------- -------Seitenumbruch------- --------- @ 0\mod_1196175311 226_0.docx @ 4165 @ @ 1

Introduction

Pos: 9/ BA/Diese Seite ist b ewusstfr eigelassen word en. @ 1\mod_12017 83680373_78.d ocx @ 54443 @ @ 1

This page has been left blank deliberately!!

Pos: 10 /BA/--- ------ ------Seitenumbruch-- ------ -------- @ 0\mo d_11961753 11226_0.doc x @ 41 65 @ @ 1

Safety

Pos: 11.1 /Überschrift en/Überschriften 1/P-T/ Sicherheit @ 0\mo d_11955667486 46_78.docx @ 635 @ 1 @ 1

3 Safety

Pos: 11.2 /BA/Sicher heit/Überarbeitete W arnhinweise/Ken nzeichnung von Hinw eiseni n der Betriebsanleit ung Einführungste xt (2 012-07-27 09:59:06) @0\ mod_1195637804 826_78.doc x@ 1098 @ 2 @ 1

3.1 Identifying Symbols in the Operating Instructions

The safety instructions contained in this manual which could result in personal injury if not

followed are identified by the general danger sign:

Pos: 11.3 /BA/Sicher heit/Überarbeitete W arnhinweise/Ken nzeichnung der Gefahre nhinweise (2012-07- 26 15:10:30) @ 28\mo d_12502443700 70_78.docx @ 2747 14@ 2 @ 1

3.2 Identification of the hazard warnings

Danger!

DANGER! - Type and source of the hazard!

Effect: Danger to life or serious injuries.

• Measures for hazard prevention

Warning !

WARNING! - Type and source of the hazard!

Effect: Injuries, serious material damage.

• Measures for hazard prevention

Caution!

CAUTION! - Type and source of the hazard!

Effect: Property damage

• Measures for risk prevention.

Pos: 11.4 /BA/Sicher heit/Überarbeitete W arnhinweise/Allg emeine Funktionshin weise ( 2012-07-26 15: 24:39) @ 0\mod_1196 869714452_78.doc x @1 5185 @ @ 1

General function instructions are indicated as follows:

Note!

Note - Type and source of the note

Effect: Economic advantage of the machine

• Actions to be taken

Instructions which are attached to the machine need to be followed and kept fully legible.

Pos: 11.5 /BA/------ ---------Seitenumbruc h--------- -------@ 0\mo d_11961753112 26_0.docx @ 4165 @ @ 1

Safety

Pos: 11.6.1 /BA/Sicherheit /Personalqualifikati onun d-sc hulung @ 0\mod_119563 9383185_78.docx @ 1136 @ 3 @ 1

3.2.1 Personnel Qualification and Training

The machine may be used, maintained and repaired only by persons who are familiar with it

and have been instructed about the dangers connected with it. The operator must define areas

of responsibility and monitoring of personnel. Should personnel lack the required knowledge,

they must receive the required training and instruction. The operator must ensure that the

contents of these operating instructions have been fully understood by personnel.

Repair work not described in these operating instructions should only be performed by

authorised service centres.

Pos: 11.6.2 /BA/Sicherheit /Gefahren bei Nichtbeachtung d erSic herheitshinweise @ 0\mod_ 1195639434013_78.d ocx@ 1 155 @ 3@ 1

3.2.2 Dangers in Case of Non-compliance with the Safety Instructions

Failure to follow the safety instructions could result in personal injury and environmental

hazards as well as damage to the machine. If the safety instructions are not respected, this

could result in the forfeiture of any claims for damages.

Failure to follow the safety instructions could result, for example, in the following hazards:

• Endangering of persons due to not protected working areas.

• Breakdown of important machine functions

• Failure of prescribed methods for repair and maintenance

• Endangering of persons due to mechanical and chemical effects

• Damage to the environment due to leaking hydraulic oil

Pos: 11.6.3 /BA/Sicherheit /Sicherheitsbewußt esArb eiten @ 0\mod_119563979 2576_78.docx @ 1174 @ 3 @ 1

3.2.3 Safety-conscious work practices

Always observe the safety instructions set out in these operating instructions, all existing

accident prevention rules and any internal work, operating and safety rules issued by the

operator.

The safety and accident prevention regulations of the responsible professional associations are

binding.

The safety instructions provided by the vehicle manufacturer should also be observed.

Observe the applicable traffic laws when using public roads.

Be prepared for emergencies. Keep the fire extinguisher and first aid box within reach. Keep

emergency numbers for doctors and fire brigade close to the telephone.

Pos: 11.6.4 /BA/----- ----------Seitenum bruch-------- -------- @0\m od_119617531 1226_0.docx @ 4165 @ @ 1

Safety

Pos: 11.6.5 /BA/Sicherheit /Sicherheits- und Unfall verhütungs-Vorschriften Maisg ebiss @ 15\mod_1232692 324226_78.docx @ 175538 @ 2 @ 1

3.3 Safety Instructions and Accident Prevention Regulations

1 Please follow all generally applicable safety and accident prevention regulations in

addition to the safety instructions contained in these operating instructions!

2 The attached warning and safety signs provide important information for safe operation.

Pay attention to these for your own safety!

3 When using public roads, make sure to observe the applicable traffic regulations!

4 Make sure that you are familiar with all equipment and controls as well as with their

functions before you begin working with the machine. It is too late to learn this when you

are using the machine for work!

5 The user should wear close fitting clothes. Avoid wearing loose or baggy clothing.

6 Keep the machine clean to prevent the danger of fire!

7 Before starting or moving the machine, make certain that nobody is in the vicinity of the

machine! (Watch for children!) Make sure that you have a clear view!

8 Carrying passengers during operation and transport on the working implement is not

permitted.

9 Couple implements correctly! Attach and secure implements to specified devices only!

10 When attaching or detaching implements, place the supporting devices in the correct

positions!

11 Special care is required when coupling and uncoupling the maize header onto or from the

forage harvester.

12 Always attach ballast weights properly to the fixing points provided!

13 Observe permitted axle loads, gross weight and transport dimensions!

14 Check and install transport equipment, such as lighting, warning devices and protective

equipment!

15 Actuating mechanisms (ropes, chains, linkage, etc.) for remotely operated devices must

be designed in such a way that, in whatever transport and working position, they cannot

trigger accidental movements.

16 Ensure that the maize header is in the prescribed condition for on-road travel and lock it

in place in accordance with the manufacturer's instructions!

17 Never leave the driver's seat when the vehicle is moving!

18 Always drive at the correct speed for the prevailing driving conditions! Avoid sudden

changes in direction when travelling uphill or downhill or across a gradient!

19 Hitched implements and ballast weights affect the driving, steering and braking response

of the machine. Make sure that you are able to brake and steer the machine as required!

20 Take into account the extension radius and/or inertia of an implement when turning

corners!

21 Take the maize header into operation only after all safety devices have been attached

and are in their proper positions!

22 Keep safety equipment in good condition. Replace missing or damaged parts.

23 Keep clear of the working range of the machine at all times!

24 Do not stand within the turning and swivel range of the implement!

25 Never operate the hydraulic folding frames if anyone is inside the swivel range!

Safety

26 Parts operated by external power (e.g. hydraulically) can cause crushing and shearing

injuries!

27 Before leaving the forage harvester, lower the maize header onto the ground, apply the

parking brake, switch off the engine and remove the ignition key!

28 There must be nobody between the forage harvester and the maize header without the

vehicle being secured against rolling away with the parking brake and wheel chocks!

29 Observe all additional information related to safety in the operating instructions for the

forage harvester.

Pos: 11.6.6 /BA/Sicherh eit/Angebaute Ger äte/Geräte angeb autMaisg ebiss @ 15\mod_ 12326925482 10_78.docx @ 175561 @ 2 @ 1

3.4 Attached devices

1 Special care is required when coupling and uncoupling the maize header onto or from the

forage harvester!

2 The maize header must only be attached to the forage harvester for which it is intended.

3 Do not work on the maize header until the engine has been stopped and the ignition key

has been removed. All operating levers should be in the neutral position and no hydraulic

lines should be under pressure.

4 Only perform jobs under the maize header when it is raised if it is securely supported.

Pos: 11.6.7 /BA/Sicherheit /Angebaute Geräte/Ger äteang ebaut Maisgebiss Zusatz Eas yCollect 6000F P @ 16\mod_1233145 266116_78.docx @ 17968 2@ @ 1

5On public highways, the maize header (EasyCollect 6000 FP) must always be in

transport position. Attach guard cloths together with flashing lights and front guard to the

maize header and connect the lighting.

Pos: 11.6.8 /BA/----- ----------Seitenum bruch-------- -------- @0\m od_119617531 1226_0.docx @ 4165 @ @ 1

Safety

Pos: 11.6.9 /BA/Sicherh eit/Zapfwellen betrieb Vorsätze/F eldhäcksler @ 13\mod _1225450981661 _78.docx @ 156341 @ 2 @ 1

3.5 PTO Operation

1 Use only PTO shafts specified by the manufacturer!

2 The guard tube and guard cone of the PTO shaft and the PTO guard must be attached

and in good working condition (on the implement side, too)!

3 Make sure that the required tube covers are in place for PTO shafts in transport and

working position!

4 Before installing or detaching PTO shafts, disengage the PTO, switch off the engine and

remove the ignition key!

5 When using PTO shafts with an overload safety or free-running coupling which are not

shielded by the guard on the tractor, mount the overload safety or free-running coupling

on the implement side!

6 Always make sure that the PTO shaft is properly installed and secured!

7 Attach chains to prevent the PTO shaft guard from rotating with the shaft!

8 Before switching on the PTO, make sure that the selected PTO speed of the forage

harvester matches the permissible speed of the implement!

9 Before switching on the PTO shaft make sure that no person is in the danger zone of the

device!

10 Never switch on the PTO if the engine is switched off!

11 No one should be in the vicinity of the rotating PTO or PTO shaft when the PTO is in use.

12 Always switch off the PTO shaft when the angle is too large or the PTO shaft is not

required!

13 Caution! After disengaging the PTO danger due to the flywheel running on! Keep away

from the implement during this time. Do not work on the machine until it has come to a

standstill.

14 Cleaning, lubricating or adjusting PTO driven implements or the PTO shaft only with PTO

disengaged, engine switched off and ignition key withdrawn!

15 Place the disconnected PTO shaft onto the support provided!

16 After detaching the PTO shaft, attach the protective cover to the PTO end!

17 If damage occurs, correct this immediately before using the implement!

Pos: 11.6.10 /BA/Sicherh eit/Zapfwellenbetrieb Zus atz@ 2\m od_12035247613 14_78.docx @ 66513 @ @ 1

Note

The instructions of the manufacturer must be observed with regard to the PTO shaft. (separate

operating instructions)

Pos: 11.6.11 /BA/------ ---------Seitenumbruc h---------------- @ 0\mod_11961 75311226_0.docx @ 4165 @ @ 1

Safety

Pos: 11.6.12 /BA/Sicherh eit/Hydraulikanlage Fel dhäcksler @ 0\mod_1195646 239935_78.docx @ 1289 @ 2 @ 1

3.6 Hydraulic system

1 The hydraulic system is pressurised!

2 When connecting hydraulic cylinders and motors, make sure the hydraulic hoses are

connected as specified!

3 When connecting the hydraulic hoses to the forage harvester hydraulics, take care that

the hydraulic system is depressurised both on the tractor side and on the device side!

4 When functions are connected hydraulically between the forage harvester and the front

attachment, coupling sleeves and plugs should be identified so that faulty operation is

excluded! If the connectors are interchanged, the functions will be reversed (e.g.

raising/lowering) - Risk of accident!

5 Check the hydraulic hose lines at regular intervals and replace them if damaged or worn!

The new hoses must fulfil the technical requirements set by the manufacturer of the

implement!

6 When searching for leaks, use suitable aids to avoid the risk of injury!

7 Liquids escaping under high pressure (hydraulic oil) can penetrate the skin and cause

serious injury! Seek medical help immediately should injuries occur! Meaning of the icons

8 Before working on the hydraulic system, depressurise the system and switch off the

engine!

Pos: 11.6.13 /BA/------ ---------Seitenumbruc h---------------- @ 0\mod_11961 75311226_0.docx @ 4165 @ @ 1

Safety

Pos: 11.6.14 /BA/Sich erheit/Wartung/ Wartung Swadro @ 2\m od_12035040221 26_78.docx @ 66245 @ 2 @ 1

3.7 Maintenance

1Always make certain that the drive and the engine are switched off before doing any

repairs, maintenance or cleaning! - Remove the ignition key!

2Regularly check that nuts and bolts are properly seated and tighten if necessary!

3When performing maintenance work with the machine raised, always secure it with

suitable supporting elements!

4Oils, greases and filters must be disposed of correctly!

5Always disconnect the power supply before working on the electrical system!

6If protective devices and guards are subject to wear, check them regularly and replace

them in good time!

7When performing electrical welding work on the vehicle and mounted devices, turn power

supply off at main battery switch or disconnect generator cable and battery!

8Replacement parts must at least comply with the technical requirements set by the

manufacturer of the implements! This is guaranteed by original KRONE spare parts!

Pos: 11.6.15 /BA/Sich erheit/Wartung/ Wartung Zusatz Schneid wekzeuge @ 12\mo d_122457827353 1_78.docx @ 151591 @ @ 1

9 When replacing working tools with cutting edges, use suitable tools and gloves!

Pos: 11.6.16 /BA/------ ---------Seitenumbruc h---------------- @ 0\mod_11961 75311226_0.docx @ 4165 @ @ 1

Safety

Pos: 11.6.17 /BA/Sicherh eit/Eigenmächtiger Umb auun dErs atzteilherstellung @ 1\mod _1201937705539_78. docx @ 55745 @ 2 @ 1

3.8 Unauthorised Conversion/Modification and Spare Parts Production

Conversions or modifications of the machine are permitted only with prior consultation with the

manufacturer. Original spare parts and accessories authorised by the manufacturer help to

ensure safety. Use of other parts may void liability for resulting damage.

Pos: 11.6.18 /BA/Sicherh eit/Unzulässige Betriebs weisen@ 1 1\mod_12233576 99923_78.docx @ 145527 @ 2 @ 1

3.9 Inadmissible Modes of Operation

The operating safety of the delivered machine is guaranteed only when it is used as intended in

compliance with the introductory section "Intended use" of the operating instructions. The limit

values listed in the data charts should not be exceeded under any circumstances.

Pos: 11.7 /BA/------ ---------Seitenumbruc h--------- -------@ 0\mo d_11961753112 26_0.docx @ 4165 @ @ 1

Page is loading ...

Krone EasyCollect 6000 FP Operating instructions

Brand: Krone

Model: EasyCollect 6000 FP

Type: Operating instructions

This manual is also suitable for

BA EasyCollect 6000 FP

Download PDF

report

Krone EasyCollect 6000 FP Operating instructions

This manual is also suitable for

Krone EasyCollect 6000 FP Operating instructions

Related papers

Other documents