Original operating instructions
Maize header
EasyCollect 450-2 FP
EasyCollect 600-2 FP
EasyCollect 750-2 FP
(from serial no.: 1136331)
Order no.: 150 000 797 07 en
18.07.2023
Table of Contents
2
CV0
EC Declaration of Conformity
We
KRONE Agriculture SE
Heinrich-Krone-Str. 10, 48480 Spelle, Germany
hereby declare as manufacturer of the product named below, on our sole responsibility,
that the
Machine: Maize header
Type: EasyCollect 450-2 FP, EasyCollect 600-2 FP,
EasyCollect 750-2 FP
to which this declaration refers is in compliance with the following relevant provisions of:
• EC Directive 2006/42/EC (Machinery)
The signing Managing Director is authorised to compile the technical documents.
Spelle, August 04, 2021
Jan Horstmann
(Managing Director, Design & Development)
Year of manufacture:
Machine no.:
Table of Contents
3
1 Table of Contents
1 Table of Contents ................................................................................................................................... 3
2 To this Document ................................................................................................................................... 8
2.1 Validity ................................................................................................................................................ 8
2.2 Re-Ordering ........................................................................................................................................ 8
2.3 Further applicable documents ............................................................................................................ 8
2.4 Target group of this document ........................................................................................................... 8
2.5 How to use this document .................................................................................................................. 9
2.5.1 Directories and References ........................................................................................................ 9
2.5.2 Direction Information ................................................................................................................... 9
2.5.3 Term “Machine” ........................................................................................................................... 9
2.5.4 Figures ........................................................................................................................................ 9
2.5.5 Scope of Document ................................................................................................................... 10
2.5.6 Means of representation ........................................................................................................... 10
2.5.7 Conversion table ....................................................................................................................... 13
3 Safety ..................................................................................................................................................... 14
3.1 Purpose of Use ................................................................................................................................. 14
3.2 Intended use ..................................................................................................................................... 14
3.3 Reasonably foreseeable misuse ...................................................................................................... 15
3.4 Service life of the machine ............................................................................................................... 15
3.5 Basic safety instructions ................................................................................................................... 16
3.5.1 Importance of the operating instructions ................................................................................... 16
3.5.2 Personnel qualification .............................................................................................................. 16
3.5.3 Personnel qualification of the technicians ................................................................................. 17
3.5.4 Children in danger ..................................................................................................................... 17
3.5.5 Coupling the machine safely ..................................................................................................... 17
3.5.6 Structural changes to the machine ........................................................................................... 18
3.5.7 Additional equipment and spare parts ...................................................................................... 18
3.5.8 Workstations on the Machine .................................................................................................... 18
3.5.9 Operational safety: Technically perfect condition ..................................................................... 19
3.5.10 Danger zones ............................................................................................................................ 20
3.5.11 Keeping safety devices functional ............................................................................................. 22
3.5.12 Personal Protective Equipment ................................................................................................. 23
3.5.13 Safety sign on the machine ....................................................................................................... 23
3.5.14 Traffic safety .............................................................................................................................. 24
3.5.15 Parking the machine safely ....................................................................................................... 24
3.5.16 Consumables ............................................................................................................................ 25
3.5.17 Dangers associated with the operational environment ............................................................. 25
3.5.18 Sources of danger on the machine ........................................................................................... 26
3.5.19 Dangers associated with certain activities: Work on the machine ............................................ 27
3.5.20 Behaviour in hazardous situations and when accidents occur ................................................. 28
3.6 Safety routines ................................................................................................................................. 29
3.6.1 Shutting down and safeguarding the machine .......................................................................... 29
3.6.2 Supporting lifted machine and machine parts securely ............................................................ 29
3.6.3 Safely checking the oil level and changing the oil and filter element ........................................ 30
3.7 Location of the safety signs on the machine .................................................................................... 32
3.8 Location and meaning of the information signs on the machine ...................................................... 36
Table of Contents
4
3.8.1 Ordering additional warning signs and information signs ......................................................... 38
3.8.2 Attaching the safety signs and information signs ...................................................................... 38
3.8.3 Contact ...................................................................................................................................... 38
4 Machine Description ............................................................................................................................ 39
4.1 Machine overview ............................................................................................................................. 39
4.2 Identification Plate ............................................................................................................................ 44
4.2.1 Contact ...................................................................................................................................... 45
4.3 Overload protection .......................................................................................................................... 46
4.4 Approved adaptations ...................................................................................................................... 47
5 Technical data ....................................................................................................................................... 49
5.1 Consumables ................................................................................................................................... 50
5.1.1 Oils ............................................................................................................................................ 50
5.1.2 Lubricating grease ..................................................................................................................... 50
5.2 Ballasting of forage harvester .......................................................................................................... 51
6 Initial operation - Claas ........................................................................................................................ 52
6.1 Checks before starting up the machine for the first time .................................................................. 52
6.2 Adapting the machine to the CLAAS forage harvester, type 493 and up ........................................ 53
6.2.1 Aligning the coupling disc ......................................................................................................... 55
7 Initial operation – John Deere ............................................................................................................. 60
7.1 Checks before starting up the machine for the first time .................................................................. 60
7.2 Adapting the machine to the John Deere forage harvester of the 6000 and 7000 series ............... 62
7.3 Adjusting the machine to the John Deere forage harvester of the series 8000 and 9000 with
universal shaft ............................................................................................................................................... 64
7.4 Adapting the machine to the John Deere forage harvester of the 8000 series and 9000 series with
header quick coupling ................................................................................................................................... 67
7.4.1 Aligning the coupling disc ......................................................................................................... 68
8 Initial operation – New Holland ........................................................................................................... 74
8.1 Checks before starting up the machine for the first time .................................................................. 74
8.2 Adapting the machine to the New Holland forage harvester............................................................ 75
9 Initial commissioning of transport chassis (for "transport chassis" version) .............................. 79
9.1 Preparing the header for mounting the transport chassis ................................................................ 79
9.2 Connecting operation panel ............................................................................................................. 80
10 Start-up - CLAAS .................................................................................................................................. 81
10.1 Checking and observing before start-up .......................................................................................... 82
10.2 Attachment to the CLAAS forage harvester ..................................................................................... 83
10.3 Coupling ........................................................................................................................................... 83
10.3.1 Connecting Drive Type 491, Type 492 ..................................................................................... 84
10.3.2 Connecting the drive, type 493 and up ..................................................................................... 85
10.3.3 Connecting hydraulics and electrics ......................................................................................... 86
11 Start-up – John Deere .......................................................................................................................... 88
11.1 Checking and observing before start-up .......................................................................................... 89
11.2 Adapting the machine to the John Deere forage harvester of the 6000 and 7000 series ............... 90
11.3 Coupling ........................................................................................................................................... 90
11.3.1 Connecting drive ....................................................................................................................... 92
11.3.2 Connecting hydraulics and electrics ......................................................................................... 93
11.4 Mounting on John Deere forage harvester of 8000 series and 9000 series .................................... 95
11.4.1 Connecting drive ....................................................................................................................... 95
11.4.2 Connecting hydraulics and electrics ......................................................................................... 97
Table of Contents
5
12 Start-up - New Holland Start-up - New Holland ................................................................................. 98
12.1 Checking and observing before start-up .......................................................................................... 99
12.2 Mounting on New Holland forage harvesters ................................................................................. 100
12.3 Coupling ......................................................................................................................................... 100
12.3.1 Connecting drive ..................................................................................................................... 102
12.3.2 Connecting hydraulics and electrics ....................................................................................... 103
13 Driving and Transport ........................................................................................................................ 105
13.1 Preparing the machine for road travel ............................................................................................ 106
13.2 Using the transport chassis (for the version with "transport chassis") ........................................... 107
13.2.1 Attaching the transport chassis ............................................................................................... 108
13.2.2 Connecting road travel lighting ............................................................................................... 111
13.2.3 Using the transport chassis ..................................................................................................... 112
13.2.4 Activating bearing pressure control of FP machines .............................................................. 113
13.2.5 Removing the transport chassis .............................................................................................. 114
13.3 Switching off the machine .............................................................................................................. 116
13.4 Lifting the machine ......................................................................................................................... 117
14 Operation ............................................................................................................................................. 118
14.1 From transport into working position .............................................................................................. 118
14.1.1 Removing the protective cover ............................................................................................... 119
14.1.2 Support jacks right/left in transport position ............................................................................ 120
14.1.3 Swinging the right-hand / left-hand side parts into working position ....................................... 121
14.2 Using the Machine for Work ........................................................................................................... 123
14.2.1 Field mode on slopes .............................................................................................................. 123
14.2.2 Insert the maize header .......................................................................................................... 124
14.2.3 Operating the main gearbox (Claas, John Deere series 6000 and 7000) .............................. 125
14.2.4 Operating input gearbox (Claas) ............................................................................................. 126
14.2.5 Setting the rotational speed of the maize header (Claas) ....................................................... 127
14.2.6 Setting rotational speed of the maize header (John Deere series 6000 and 7000) ............... 128
14.2.7 Setting rotational speed of the maize header (John Deere series 8000 and 9000) ............... 129
14.2.8 Setting rotational speed of the maize header (New Holland) ................................................. 129
14.2.9 Operating row detection (for the version with “row detection”) ............................................... 130
14.2.10 Operating active ground contour (for the version with “active ground contour”)..................... 133
14.3 Switching from working position to transport position .................................................................... 137
14.3.1 Swinging the right hand / left hand side parts upward into transport position ........................ 137
14.3.2 Installing guard on the right/left ............................................................................................... 139
14.3.3 Installing the front guard.......................................................................................................... 139
14.3.4 Connecting indicators and position lights on the right/left....................................................... 140
14.4 Detaching the machine................................................................................................................... 141
14.4.1 Moving the right hand / left hand parking supports into parking position ................................ 141
14.4.2 Swinging the right-hand / left-hand side parts into working position ....................................... 142
14.5 Dismantling the machine in case of adaptation to Claas forage harvester .................................... 143
14.5.1 Disconnecting hydraulics and electrics ................................................................................... 143
14.5.2 Connecting .............................................................................................................................. 144
14.5.3 For version with universal shaft (e.g. type 491 und 492) ........................................................ 145
14.5.4 Version with header quick coupling (type 493 and up) ........................................................... 145
14.6 Dismantling the machine in case of adaptation to John Deere forage harvester of 6000 and 7000
series 146
14.6.1 Disconnecting hydraulics and electrics ................................................................................... 146
14.6.2 Connecting .............................................................................................................................. 147
Table of Contents
6
14.7 Removing the machine with adaptation to John Deere forage harvesters of the series 8000 and
9000 149
14.7.1 Disconnecting hydraulics and electrics ................................................................................... 149
14.7.2 Disconnecting header ............................................................................................................. 150
14.8 Dismantling the machine in case of adaptation to Claas forage harvester .................................... 151
14.8.1 Disconnecting hydraulics and electrics ................................................................................... 151
14.8.2 Connecting .............................................................................................................................. 152
14.9 Removing the machine and storing it with supports (for the version with supports) ...................... 153
14.9.1 Support jacks right/left in transport position ............................................................................ 154
14.9.2 Relocating the support jack bracket ........................................................................................ 154
14.9.3 Mounting console support ....................................................................................................... 155
14.9.4 Mounting side guards .............................................................................................................. 156
14.9.5 Setting the lateral supports at rear .......................................................................................... 157
14.9.6 Putting header down ............................................................................................................... 158
15 Settings ............................................................................................................................................... 159
15.1 Setting the Tubular Bars ................................................................................................................ 160
15.1.1 Setting the tubular bar in terms of its inclination (EasyCollect 600-2 FP, 750-2 FP) .............. 161
15.1.2 Setting the tubular bar in terms of its inclination (EasyCollect 450-2 FP, 750-2 FP) .............. 163
15.2 Adjusting the crop press roller (for version without transport chassis) .......................................... 164
15.3 Setting Holding-Down Device Roller .............................................................................................. 164
15.4 Adjusting skids ............................................................................................................................... 164
15.5 Adjusting the plant dividers ............................................................................................................ 165
15.6 Adapting Star-shaped Conveyor Height to Maize Crop ................................................................. 166
15.7 Adjusting the oscillation of the header ........................................................................................... 167
16 Maintenance ........................................................................................................................................ 169
16.1 Special Safety Instructions ............................................................................................................. 170
16.1.1 Test run ................................................................................................................................... 170
16.2 Spare Parts .................................................................................................................................... 170
16.3 Maintenance table .......................................................................................................................... 171
16.4 Tightening torques .......................................................................................................................... 173
16.4.1 Metric Thread Screws with Control Thread............................................................................. 173
16.4.2 Metric Thread Screws with Fine Thread ................................................................................. 174
16.4.3 Metric Thread Screws with Countersunk Head and Hexagonal Socket ................................. 174
16.4.4 Tightening Torques for Locking Screws and Bleed Valves on the Gearboxes ....................... 175
16.5 Hydraulics ....................................................................................................................................... 176
16.6 Input gearbox ................................................................................................................................. 177
16.7 Main gearbox .................................................................................................................................. 179
16.8 Collector Gearbox .......................................................................................................................... 180
16.9 Intermediate gearbox ..................................................................................................................... 182
16.10 Roller Gearbox ............................................................................................................................... 183
16.11 Checking and adjusting the collector tension ................................................................................. 184
16.11.1 Checking the collector pre-tension .......................................................................................... 184
16.11.2 Adjusting the collector pretension ........................................................................................... 184
16.11.3 Checking the collector pre-tension .......................................................................................... 185
16.11.4 Adjusting the collector pretension ........................................................................................... 185
16.11.5 Checking the Collector Tensioning Function .......................................................................... 186
16.11.6 Setting the collector tensioning function ................................................................................. 186
16.12 Adjusting the Scraper ..................................................................................................................... 187
16.13 Setting Infeed Sheets ..................................................................................................................... 188
Table of Contents
7
16.14 Changing the tips ........................................................................................................................... 189
16.15 Adjusting the tips ............................................................................................................................ 189
16.15.1 Adjusting the side tips ............................................................................................................. 190
16.15.2 Adjusting the row tips .............................................................................................................. 190
16.15.3 Adjusting the central tip ........................................................................................................... 190
16.16 Removing and Installing Guide Bracket at Tip Retainer ................................................................ 191
16.17 Converting Tip Retainer for Special Row Distances ...................................................................... 192
16.18 Releasing star ratchet clutch at the universal shaft ....................................................................... 193
16.19 Blade Changing .............................................................................................................................. 194
16.19.1 Changing bow and step blades ............................................................................................... 194
16.19.2 Changing the cutting blades ................................................................................................... 196
16.19.3 Changing the scraper blade .................................................................................................... 198
16.20 Replacing the wear plates .............................................................................................................. 198
16.21 Checking/adjusting the distance between bottom guide roller and guide rail ................................ 199
16.22 Check hydraulic hoses ................................................................................................................... 201
16.23 Maintaining and checking the tyres (for the version with "transport chassis") ............................... 201
17 Maintenance – lubrication ................................................................................................................. 202
17.1 Special Safety Instructions ............................................................................................................. 202
17.2 Lubrication Chart ............................................................................................................................ 204
18 Placing in Storage .............................................................................................................................. 209
19 Before the Start of the New Season ................................................................................................. 210
19.1 Special Safety Instructions ............................................................................................................. 210
19.2 Test run. ......................................................................................................................................... 211
20 Disposal of the machine .................................................................................................................... 212
20.1 Disposal of the machine ................................................................................................................. 212
21 Index .................................................................................................................................................... 213
To this Document
8
2 To this Document
2.1 Validity
These operating instructions are valid for the maize header of the following types:
EasyCollect 450-2 FP; EasyCollect 600-2 FP; EasyCollect 750-2 FP
2.2 Re-Ordering
You can request a replacement document if this document became completely or partly
unusable, or if you need it in a different language. Please specify the document number shown
on the cover page in your order. Contact data can be found in the chapter “Contact persons”.
The document can additionally be downloaded via KRONE MEDIA https://media.mykrone.green
.
2.3 Further applicable documents
To ensure that the machine is used safely and as intended, observe the following further
applicable documents:
– Operating instructions of universal shaft(s)
– Forage harvester operating instructions
2.4 Target group of this document
This document aims at the operators of the machine fulfilling the minimum requirements of
personnel qualification; refer to chapter entitled Safety “Personnel Qualification”.
To this Document
9
2.5 How to use this document
2.5.1 Directories and References
Table of contents/headers:
The table of contents as well as the headers in this instruction are used for quick navigation in
the chapters.
Index directory:
In the index directory, you can find information on the desired subject via catchwords which are
in alphabetical order. The index directory can be found on the last page of this instruction.
Cross references:
Cross references to another place in the operating instructions or to another document are in
the text and specify the chapter and subchapter or section. The designation of subchapters or
sections is presented in quotation marks.
Example:
Check that all screws on the machine are tight, refer to chapter Maintenance, “Tightening
Torques”.
The subchapter or the section can be found via an entry in the table of contents and in the index
directory.
2.5.2 Direction Information
Direction information in this document such as front, rear, right and left always applies in the
direction of travel.
2.5.3 Term “Machine”
In the rest of this document the maize header is also referred to as the "machine".
2.5.4 Figures
The figures in this document do not always represent the exact machine type. The information
which refers to the figure always corresponds to the machine type of this document.
To this Document
10
2.5.5 Scope of Document
In addition to standard equipment, accessories kits and versions of the machine are described
in this document. Your machine may deviate from this document.
2.5.6 Means of representation
Icons in the text
In this document, the following means of representation are used:
Action step
A bullet point (•) designates an action step you have to perform, as for example:
• Set the left outside mirror.
Sequence of actions
Several bullet points (•) located in front of a sequence of action steps identify a sequence of
actions to be performed step by step, as for example:
• Loosen counter nut.
• Set the screw.
• Tighten counter nut.
List
Dashes (-) identify lists such as, for example:
– Brakes
– Steering
– Lighting
To this Document
11
Symbols in figures
To visualize parts and actions steps, the following icons are used:
Icon
Explanation
1
Reference sign for part
I
Position of a part (e.g. move from pos. I to pos. II)
X
Dimensions (e.g. B = width, H = height, L = length)
Action step: Tighten screws with torque key with specified tightening torque
Direction of motion
Direction of travel
opened
closed
enlargement of display detail
Framings, dimension line, dimension line limitation, reference line for visible parts
or visible mounting material
Framings, dimension line, dimension line limitation, reference line for covered
parts or covered mounting material
Laying routes
LH
Left-hand machine side
RH
Right-hand machine side
To this Document
12
Warning signs
Warning
WARNING! - Type and source of hazard!
Effect: Injuries, serious material damage.
• Measures for hazard prevention.
Caution
CAUTION! - Type and source of hazard!
Effect: Damage to property.
• Measures for risk prevention.
Notes with information and recommendations
Note
Note
Effect: Economic benefit of the machine.
• Measures to be performed.
To this Document
13
2.5.7 Conversion table
By means of the following table, metric units can be converted into US units.
Quantity
SI Units (Metric)
Factor
Inch-Pound Units
Unit Name
Abbreviation
Unit Name
Abbreviation
Area
hectare
ha
2.47105
acre
acres
Flow
liters per
minute
L/min
0.2642
US gallon per
minute
gpm
cubic meter
per hour
m³/h
4.4029
Force
newton
N
0.2248
pound-force
lbf
Length
millimeter
mm
0.03937
inch
in.
meter
m
3.2808
foot
ft.
Power
kilowatt
kW
1.3410
horsepower
hp
Pressure
kilopascal
kPa
0.1450
pound per
square inch
psi
megapascal
MPa
145.0377
bar (non-SI)
bar
14.5038
Torque
newton meter
Nm
0.7376
pound-foot or
foot-pound
ft∙lbf
8.8507
pound-inch or
inch-pound
in∙lbf
Temperature
degree
Celsius
°C
°Cx1.8+32
degree
Fahrenheit
°F
Velocity
meter per
minute
m/min
3.2808
foot per
minute
ft/min
meter per
second
m/s
3.2808
foot per
second
ft/s
kilometer per
hour
km/h
0.6215
miles per
hour
mph
Volume
liter
L
0.2642
US gallon
US gal.
milliliter
ml
0.0338
US ounce
US oz.
cubic
centimeter
cm³
0.0610
cubic inch
in³
Weight
kilogram
kg
2.2046
pound
lbs
Safety
14
3 Safety
3.1 Purpose of Use
The KRONE maize header EasyCollect 450-2 FP, EasyCollect 600-2 FP, EasyCollect 750-2 is
a crop header including an adaptation for mounting it on certain forage harvester types of the
brands Claas, John Deere and New Holland.
The KRONE maize header EasyCollect 450-2 FP, EasyCollect 600-2 FP, EasyCollect 750-2 FP
is used for harvesting maize and other thick-stalked forage plants independently of rows.
Ver
3.2 Intended use
This machine is a maize header and is used to cut crops and to feed them to the forage
harvester.
The crops designated for the intended use of this machine are stem-type crops such as maize
plants.
The machine is designed exclusively for use in agriculture and may only be used when
– all safety devices are available according to the operating instructions and are in the
protective position.
– all safety instructions of the operating instructions have been observed and complied with,
both in chapter “Basic safety instructions” and directly in the chapters of the operating
instructions.
The machine may be used only by people who satisfy the personnel qualification requirements
designated by the machine manufacturer.
These operating instructions are part of the machine and must therefore be at hand when the
machine is in use. The machine may be operated only when the operator has received training
and in compliance with these operating instructions.
If the machine is used for applications which are not described in these operating instructions,
this may result in serious injuries or death and damage to the machine and other property.
Unauthorised modifications to the machine may affect the properties of the machine or disrupt
the proper operation. For this reason, unauthorised modifications shall exclude any liability of
the manufacturer for consequential damage.
The intended use shall also include the adherence to the operating, maintenance and repair
conditions set by the manufacturer.
Safety
15
3.3 Reasonably foreseeable misuse
Any use beyond the intended use, see chapter Safety, “Intended use”, is regarded as improper
use and is therefore misuse according to the Machinery Directive. The manufacturer is not liable
for damage resulting from this, the user alone bears the risk.
Such misuse is for example:
– Processing of crops which are outside the intended use of the machine, see chapter Safety,
“Intended use”
– Transportation of people
– Transportation of goods
– Exceedance of the permitted technical total weight of the carrier vehicle
– Non-compliance with the safety signs on the machine and safety notices in the operating
instructions
– Performing fault clearance, setting, cleaning, repair and maintenance work contrary to the
information in the operating instructions
– Unauthorised modifications to the machine
– Attachment of unauthorised or unapproved additional equipment
– Use of spare parts which are not KRONE original spare parts
– Stationary operation of the machine
Unauthorised modifications to the machine may affect the properties of the machine or disrupt proper
operation. For this reason, unauthorised modifications will release the manufacturer from any liability for
consequential damage.
3.4 Service life of the machine
– The service life of this machine strongly depends on proper use and maintenance as well as
the operating conditions.
– Permanent operational readiness as well as long service life of the machine can be
achieved by observing the instructions and notes of these operating instructions.
– After each season of use, the machine must be checked thoroughly for wear and other
damage.
– Damaged and worn parts must be replaced before placing the machine into service again.
– After the machine has been used for five years, carry out full technical inspection of the
machine. According to the results of this inspection, a decision concerning the possibility of
reuse of the machine should be taken.
Safety
16
3.5 Basic safety instructions
Non-compliance with the safety instructions and warnings
Non-compliance with the safety instructions and warnings may result in injuries and damage to
the environment and property.
3.5.1 Importance of the operating instructions
The operating instructions are an important document and a part of the machine. They are
aimed at the user and contain safety-relevant information.
Only the procedures indicated in the operating instructions are reliable. If the operating
instructions are not observed, people may be seriously injured or killed.
• Before using the machine for the first time, read and follow all the “Basic Safety Instructions”
in the Safety chapter.
• Before working, also read and observe the respective sections in the operating instructions.
• Keep the operating instructions ready to hand for the user of the machine.
• Hand over the operating instructions to subsequent users.
3.5.2 Personnel qualification
If the machine is not used properly, people may be seriously injured or killed. To avoid
accidents, each person who works with the machine must satisfy the following minimum
requirements:
– He is physically capable of controlling the machine.
– He can work safely with the machine in accordance with these operating instructions.
– He understands the method of operation of the machine within the scope of his work and
can identify and avoid the dangers associated with the work.
– He has read the operating instructions and can implement the information in the operating
instructions accordingly.
– He is familiar with driving vehicles safely.
– For road travel he has adequate knowledge of the highway code and has the stipulated
driving licence.
Safety
17
3.5.3 Personnel qualification of the technicians
If the work (assembly, conversion, modification, extension, repairs, retrofitting) is performed
improperly on the machine, people may be seriously or fatally injured. To avoid accidents,
everyone who performs work according to these instructions must meet the following minimum
requirements:
• Qualified professional, with relevant training.
• Capable of assembling the (partially) disassembled machine according to the assembly
instructions provided by the manufacturer.
• Capable of extending, modifying or repairing the function of the machine according to the
relevant instructions provided by the manufacturer.
• Ability to perform the work safely according to these instructions.
• Understands the mode of operation of the work to be performed and the machine and is
able to identify and avoid the hazards associated with the work.
• Has read these instructions and is able to apply the information in these instructions
accordingly.
3.5.4 Children in danger
Children cannot assess danger and behave unpredictably.
As a result, children are especially at risk.
• Keep children away from the machine.
• Keep children away from consumables.
• Especially before starting up and moving the machine, ensure that there are no children in
the danger zone.
3.5.5 Coupling the machine safely
When the machine is connected incorrectly to a forage harvester, dangers are caused which
could lead to severe accidents.
• Observe all operating instructions when connecting:
– The operating instructions of the machine
– The operating instructions of the forage harvester
– The operating instructions of universal shaft
• Follow the coupling instructions, see chapter Initial Operation, “Adjusting the Machine to
Forage Harvester” and chapter Initial Operation “Attaching to the Forage Harvester”.
• Observe the changed driving behaviour of the combination.
Safety
18
3.5.6 Structural changes to the machine
Structural changes and enhancements may impair the functionality and operational safety of the
machine. Thus there is a risk of serious injuries or death.
Structural changes and enhancements are not permitted.
3.5.7 Additional equipment and spare parts
Additional equipment and spare parts which do not comply with the requirements of the
manufacturer may impair the operational safety of the machine and cause accidents.
• To ensure operational safety, use original parts or standard parts which correspond to the
requirements of the manufacturer.
3.5.8 Workstations on the Machine
Passengers
Passengers may be seriously injured by the machine or fall off the machine and get run over.
Ejected objects may strike and injure passengers.
• Never let people ride on the machine.
Safety
19
3.5.9 Operational safety: Technically perfect condition
Operation only when the machine has been started up correctly
If the machine is not started up correctly according to these operating instructions, the
operational safety of the machine is not ensured. As a result, accidents may occur and people
may be seriously injured or killed.
• Do not use the machine unless it has been started up correctly, see chapter Start-up.
Technically perfect condition of the machine
Improper maintenance and adjustment may affect the operational safety of the machine and
cause accidents. As a result, people may be seriously injured or killed.
• Perform all maintenance and adjustment work according to the chapters Maintenance and
Adjustment.
• Before performing any maintenance or adjustment work, shut down and safeguard the
machine, see chapter Safety "Shutting down and safeguarding the machine".
Danger resulting from damage to the machine
Damage to the machine may impair the operational safety of the machine and cause accidents.
As a result, people may be seriously injured or killed. The following parts of the machine are
particularly important for safety:
– Safety devices
– Connecting devices
– Hydraulic system
– Universal shafts
If there are doubts about the operational safety of the machine, for example due to leaking fuel,
visible damage or an unexpected change to the operational behaviour:
• Shut down and safeguard the machine, see chapter Safety, "Shutting down and
safeguarding the machine".
• Immediately eliminate potential causes of damage, for example heavy soiling, or tighten
slack screws.
• If possible, repair the damage according to these operating instructions.
• In the case of damage which may affect operational safety and cannot be repaired
according to these operating instructions: Have damage repaired by a qualified service
centre.
Technical limit values
If the technical limit values of the machine are not observed, the machine may be damaged. As
a result, accidents may occur and people may be seriously injured or killed. Observance of the
following technical limit values is particularly important for safety:
– Maximum permitted operating pressure of hydraulics
– Maximum permitted drive speed
– Maximum permitted axle loads of forage harvester
• Observe limit values, refer to chapter “Technical Data”.
Safety
20
3.5.10 Danger zones
When the machine is switched on, a danger zone may be created around this machine.
To avoid getting into the danger zone of the machine, maintain at least the safety distance.
If the safety distance is not followed, people may be seriously injured or killed.
• Do not switch on the drives and the engine until you are sure that no one has ignored the
safety distance.
• If people ignore the safety distance, switch off the drives.
• Stop the machine in the shunting operation and field mode.
The safety clearance is:
For machine in shunting operation and
field mode
In front of the machine
30 m
Behind the machine
5 m
Laterally to the machine
3 m
For machine switched on without driving motion
In front of the machine
3 m
Behind the machine
5 m
Laterally to the machine
3 m
The safety distances named here are minimum distances according to the intended use. These
safety distances must be increased depending on operating conditions and environmental
conditions, when required.
• Before performing any work in the danger zone of the machine: Shut down and safeguard
the machine, see chapter Safety, "Shutting down and safeguarding the machine". This also
applies to brief inspection work.
• Consider the information in all relevant operating instructions:
– The operating instructions of the machine
– The operating instructions of the universal shaft
– The operating instructions of the forage harvester
– The operating instructions of the transport wagon
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/