LBL Lighting LW681PELED Installation guide

Type
Installation guide

LBL Lighting LW681PELED is a wall-mounted LED light fixture suitable for damp locations. It can be dimmed with a low-voltage electronic dimmer and mounted to a 4” square electrical box with a round plaster ring or an octagon electrical box. The fixture requires installation by a qualified electrician and includes two #8-32 screws for attaching the mounting plate to the electrical box. The shade is attached to the mounting plate by sliding it into the slots on the backplate and pushing down on the shade's frame until it is firmly inside the mounting clips.

LBL Lighting LW681PELED is a wall-mounted LED light fixture suitable for damp locations. It can be dimmed with a low-voltage electronic dimmer and mounted to a 4” square electrical box with a round plaster ring or an octagon electrical box. The fixture requires installation by a qualified electrician and includes two #8-32 screws for attaching the mounting plate to the electrical box. The shade is attached to the mounting plate by sliding it into the slots on the backplate and pushing down on the shade's frame until it is firmly inside the mounting clips.

Install the Fixture
1A
Wall
1B
CAUTION - RISK OF FIRE
This product requires installation by a qualified
electrician. Before installing be sure to read all
instructions and TURN THE POWER TO THE
ELECTRICAL BOX OFF.
CAUTION - RISK OF FIRE
This product requires installation by a qualified
electrician. Before installing be sure to read all
instructions and TURN THE POWER TO THE
ELECTRICAL BOX OFF.
CAUTION - RISK OF FIRE
This product requires installation by a qualified
electrician. Before installing be sure to read all
instructions and TURN THE POWER TO THE
ELECTRICAL BOX OFF.
GENERAL PRODUCT INFORMATION:
This product is suitable for damp locations.
This product can mount either to a 4” square electrical box with a
round plaster ring or an octagon electrical box.
This product can be dimmed with a low-voltage electronic dimmer.
This instruction shows a typical installation.
THUMB SCREW
THUMB SCREW
LED PLATE
To gain access to the mounting plate holes, remove the
two thumb screw to temporarily loosen the plate
holding the LED lamp.
1
DRIVER
62
63
Connect the mounting plate ground wire to a suitable
ground in accordance to local electrical codes.
Connect the white driver wire to the neutral power line
wire with a wire nut.
Connect the black driver wire to the hot power line wire
with a wire nut.
64
1
4
3
2
Installation Instructions for
Fiona Wall (LED)
980FIONAWD
1.0
LW681_LED
Install the Shade
2A
Slide the shade into the slots on the backplate.
Align and center the shade to the mounting clips on
the mounting plate.
Mount the shade by evenly pushing down on the
shade’s frame until they are firmly inside the mounting
clips.
1
7400 Linder Ave, Skokie, IL 60077
800.323.3226 - 847.626.6300
www.lbllighting.com
© 2012 LBL Lighting.All rights reserved.The "LBL Lighting" graphic is a
registered trademark of LBL Lighting. LBL Lighting reserves the right to
change specifications for product improvements without notification.
A Generation Brands Company
SAVETHESE INSTRUCTIONS!
2
2
1C
66
Properly place all wire, wire nut connections, and the
driver inside the electrical box.
Attach the mounting plate to the electrical box using
the two #8-32 screws provided.
5
6
1D
THUMB SCREW
THUMB SCREW
LED PLATE
67
Re-install the LED Plate and secure it tightly with the
two thumb screws.
1
1
1
1
3
3
3
3
3
  • Page 1 1
  • Page 2 2

LBL Lighting LW681PELED Installation guide

Type
Installation guide

LBL Lighting LW681PELED is a wall-mounted LED light fixture suitable for damp locations. It can be dimmed with a low-voltage electronic dimmer and mounted to a 4” square electrical box with a round plaster ring or an octagon electrical box. The fixture requires installation by a qualified electrician and includes two #8-32 screws for attaching the mounting plate to the electrical box. The shade is attached to the mounting plate by sliding it into the slots on the backplate and pushing down on the shade's frame until it is firmly inside the mounting clips.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI