Kaba C-lever compact Installation Instructions Manual
- Type
- Installation Instructions Manual
EN
Kaba c-lever compact
Installation instructions
Doc no.: k2evo703en-2011-05
Manufacturer:
Kaba GmbH
Ulrich-Bremi-Strasse 2
A-3130 Herzogenburg
Tel.: +43 (0) 2782 808 - 0
Fax: +43 (0) 2782 808 - 5505
www.kaba.com/cylinders-locks
Sales:
Kaba GmbH Kaba GmbH Kaba AG
Ulrich-Bremi-Strasse 2 Philipp-Reis-Strasse 14 Mühlebühlstrasse 23, Postfach
A - 3130 Herzogenburg DE- 63303 Dreieich CH- 8620 Wetzikon
Tel. +43 (0) 2782 808 - 0 Tel. +49 (0) 6103 99 070 Tel. +41 (0) 848 85 86 87
Fax: +43 (0) 2782 808 - 5505 Fax: +49 (0) 6103 99 07 133 Fax: +41 (0) 44 931 63 85
www.kaba.at www.kaba.de www. kaba.ch
Kaba® is a registered trademark of Kaba AG.
This documentation may not be reproduced in any way
or otherwise used without the written consent of Kaba GmbH.
Copyright by Kaba GmbH
Installation instructions Contents
Kaba c-lever compact k2evo703en-2011-05 3
1 Please read first . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Validity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2 Target group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.3 Content and purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.4 Supplementary documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.5 Attention and warning symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.5.1 Hazards to personnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.5.2 Hazards to property . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.5.3 Other information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.6 Definition of terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2 Safety and the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1 Proper use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2 Safety guidelines for this product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2.1 ESD protective measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2.2 Handling of lithium batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.3 Disposal of packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.4 Disposal of the actuator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.5 Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3 Product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1 Scope of supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2 Additional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.3 Preparatory measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.3.1 Door requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.3.2 Lock requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.4 Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.5 c-lever compact assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.6 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.1 Tools required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.2 Drilling the fastening holes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.3 Assembling the mechatronic unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.4 Installing the actuator in the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.1 Operation signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Contents
4 k2evo703en-2011-05 Kaba c-lever compact
Contents Installation instructions
6 Maintenance and troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6.1 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6.1.1 Replacing the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6.1.2 Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6.1.3 Reading Traceback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6.1.4 Emergency opening for discharged batteries . . . . . . . . . . . . . . . . . 19
6.2 INI reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.2.1 Initialising the electronic module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.3 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.4 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6.4.1 Possible faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Installation instructions Please read first
Kaba c-lever compact k2evo703en-2011-05 5
1 Please read first
1.1 Validity
These instructions describe installation, maintenance and troubleshooting tips
for the Kaba c-lever compact and are valid for the 2724 MID, 2725 MID, 2724 LEA
and 2725 LEA variants.
1.2 Target group
These instructions are addressed to specialist staff for the assembly, installation,
set-up, service and maintenance of this product.
The description is intended for trained personnel and does not replace product
training.
1.3 Content and purpose
The content of these instructions is limited to the installation and maintenance
of the Kaba c-lever compact. Detailed information about programming can be
found in the supplementary documentation.
1.4 Supplementary documentation
Technical information and help in the planning of installations can be found in
the technical data sheets or the Kaba evolo catalogue.
Detailed information about programming this product can be found in the Kaba
Programmer 1460 user manual and Kaba evolo Manager software.
1.5 Attention and warning symbols
The following attention and warning symbols, which point out hazards and
special characteristics, are used in these instructions.
Pay attention to these hazard notes. They help to avoid accidents and prevent
damage.
Installation instructions Please read first
Kaba c-lever compact k2evo703en-2011-05 6
1.5.1 Hazards to personnel
1.5.2 Hazards to property
1.5.3 Other information
Practical tips and useful information. These ensure that optimum use is made of
the product and its functions.
1.6 Definition of terms
In order to make it easier to read these instructions, the Kaba c-lever compact is
shortened to actuator, the 1460 programming device is shortened to programmer
and the Kaba evolo Manager software is shortened to KEM.
CAUTION
Indicates a potentially dangerous situation that can lead to minor injury.
Risk of explosion
Indicates a potentially dangerous situation that can lead to minor injury.
ATTENTION
Identifies a possible dangerous situation that can lead to product damage or to
damage to its environment.
Installation instructions Safety and the environment
Kaba c-lever compact k2evo703en-2011-05 7
2 Safety and the environment
2.1 Proper use
The Kaba c-lever compact may only be used and operated for its intended
purpose, i.e. opening and closing doors. Other uses are not permitted.
2.2 Safety guidelines for this product
2.2.1 ESD protective measures
2.2.2 Handling of lithium batteries
ATTENTION
Danger of damage to electronic components from electrostatic discharge.
This product contains electronic components that are sensitive to electrostatic
discharge (ESD). Contact by persons or objects can cause an electrostatic
discharge that may damage or destroy the product. To avoid the risk of
electrostatic discharge, note the handling guidelines and recommendations
according to EN100015-1.
Only transport and send removed modules in protective bags.
Risk of explosion
Lithium batteries can explode or burst explosively.
Improper handling of lithium batteries can lead to fires and explosions.
- Only replace lithium batteries with batteries of the same type.
- No not open, pierce or crush lithium batteries.
- Do not burn lithium batteries or expose them to high temperatures.
- Do not short-circuit lithium batteries.
- Do not recharge lithium batteries.
Installation instructions Safety and the environment
Kaba c-lever compact k2evo703en-2011-05 8
2.3 Disposal of packaging
Dispose of packaging in accordance with environmental regulations
The packaging is recyclable. Please do not dispose of the packaging with
household waste, instead dispose of with waste for recycling.
2.4 Disposal of the actuator
Do not dispose of the actuator in household waste
Dispose of electronic devices and used batteries in accordance with the Act on
Disposal of Waste Electrical and Electronic Equipment [Verordnung über
Entsorgung von Elektro- und Elektronik-Altgeräten] (VREG/WEEE) at a local
collection point for waste electronic equipment.
2.5 Conformity
This actuator fulfils the requirements of the R&TTE Directive 1999/5/EC and the
EMC Directive 89/336//EEC.
Installation instructions Product description
Kaba c-lever compact k2evo703en-2011-05 9
3 Product description
3.1 Scope of supply
The Kaba c-lever compact is supplied with the following accessories:
- 1 Kaba c-lever compact
- 1 inside handle (as per catalogue)
- 1 Direction pin
- 2 batteries, type AAA Lithium
- 1 spindle
- Various fixing materials
- 2 centring sleeves 7-8 mm
- 2 centring sleeves 7-9 mm
- 1 dismantling key
- 1 quick reference guide
External handles are not included in the scope of supply, however they can be
ordered at the same time from the catalogue!
3.2 Additional accessories
- Adapter pins, product number 1355-42A
- Programming cable, product number 1355-42
- Kaba 1460 Programmer
- Kaba media
- Kaba evolo Manager software
3.3 Preparatory measures
3.3.1 Door requirements
The door thickness must be between 39 mm and 94 mm.
3.3.2 Lock requirements
The Kaba c-lever compact can be used with most commercially available door
locks. Only use locks from established manufacturers, as this is the only way to
ensure that rosette drillings conform to the standards.
Locks with a split follower cannot be used!
To guarantee emergency opening with the help of the locking cylinder, door
locks with a key operated latch must be fitted!
Installation instructions Product description
Kaba c-lever compact k2evo703en-2011-05 10
3.4 Technical specifications
Interface
Data transfer RFID
Dimensions
Fitting HxWxD 108.5 x 60 x x25.8 mm
Pin size (standard) at least 45 mm
(depending on the door and lock)
Body
Handle Stainless steel
Power supply
Battery 2 x 1.5 V, type AAA Lithium
Service life: > 90,000 cycles or 3 years
Operating environments
Protection class IP54
Temperature -25° ... +70° C 1)
Humidity 0 ... 95% rH, non-condensing
Climate Not suitable for heavily corrosive atmospheres
(chlorine, ammonia)
Rooms Not to be used in environments where there is a risk
of explosion
Standards
Fire protection According to EN1634-1
EN179 According to test certificate
Key:
1) The temperature range depends on the battery manufacturer's specifications
Installation instructions Product description
Kaba c-lever compact k2evo703en-2011-05 11
3.5 c-lever compact assembly
Exploded diagram
3.6 Dimensions
Scale drawing
21 3456
7
8101112
13 9
14 15
Position Description
1 Mechatronic unit
2Housing
3Metal ring
4 Plastic guide ring
5 External handle
6Direction pin
7 Batteries, type AAA Lithium (2 pieces)
8Spindle
9 Fastening screw
10 Internal rosette "round" (optional)
11 Fixing screw for internal rosette (2 pieces)
12 Internal rosette cover (optional)
13 Inside handle (optional)
14 Fixing screw for handle (optional)
15 Centring sleeve (2 pieces 7-8 mm, 2 pieces 7-9 mm)
60
108.5
114.7
65
25.8
Ø6.5
5
38
Installation instructions Installation
Kaba c-lever compact k2evo703en-2011-05 12
4 Installation
Installation description and illustrations with internal rosette!
4.1 Tools required
• Power drill with Ø7.2 mm drill bit
•Philips screwdriver
4.2 Drilling the fastening holes
ATTENTION
A lock that is already in place can be damaged.
To avoid damage, remove the lock before starting to drill.
Preparing the door
1. Remove the existing furniture or
rosette fittings.
Mark the drill holes
2. Mark the drill holes (if not in
place) according to the drawing
on the outside and/or inside of
the door.
3. Close the door lock.
If available the 2720-25 drill jig can
also be used!
Drilling fixing holes
4. If there are no rosette drill holes,
drill the fixing holes with a Ø7.2
mm drill from both sides of the
door (e.g. according to DIN 18255
standard).
5. After drilling, clean the mortise
and refit the door lock.
38
Ø7.2 (2x)
Installation instructions Installation
Kaba c-lever compact k2evo703en-2011-05 13
4.3 Assembling the mechatronic unit
Inserting the direction pin
1. Insert direction pin (6) into the
mechatronic unit (1) so that the
"R" can be read from the front on
a right hand door and the "L" on a
left hand door during use.
To make it easier to slide in, turn the
square spindle of the mechatronic unit
(1) anti-clockwise for right-hand doors,
and clockwise for left-hand doors, as
far as the limit stop when inserting the
direction pin (6)!
Inserting batteries
2. Insert batteries (7) into the
mechatronic unit (1) as shown.
Ensure correct battery polarity!
7
1
Detail X
6
1
Installation instructions Installation
Kaba c-lever compact k2evo703en-2011-05 14
4.4 Installing the actuator in the door
Fit the housing and handle
3. Push the housing (2) over the
mechatronic unit (1).
4. Position the metal ring (3) and
the guide ring (4) on the lever
handle bearing of the
mechatronic unit (1).
5. Fit the lever handle (5) onto the
square spindle of the
mechatronic unit (1).
Lever handle (5) must engage audibly
when fitting!
Inserting the spindle
6. Insert the spindle (8) into the
square of the mechatronic unit
(1) and secure with a fastening
screw (9).
If there are drill holes already in the
door that are larger than Ø7.2 mm, the
centring ring (15) provided must be
attached. This prevents movement of
the actuator in the door.
Inserting the actuator into the door
1. Position the actuator with the
spindle (8) through the lock hub
in the door.
Fit the internal rosette
2. Fit the optional internal rosette
(10) with plastic attachment
downwards on the inside of the
door and secure with fixing
screws (11).
8
10
11
9
8
1
15
1 2
345
Installation instructions Installation
Kaba c-lever compact k2evo703en-2011-05 15
3. Fit the cover (12) over the internal
rosette (10).
4. Push the handle (13) onto the
spindle (8) until there is an
audible click and fix with a fixing
screw (14).
14
12 10
13
Installation instructions Operation
Kaba c-lever compact k2evo703en-2011-05 16
5Operation
5.1 Operation signals
The acoustic signals may first have to be activated using the Programmer!
Action Acoustic
signal
Optical
signal Confirmation
Master A/B authorised
(open programming
window)
1 x short 1 x green The acoustic signal sounds if
the medium is taken out of
range of the antenna.
Add user medium 1 x short 1 x green
Delete user medium 2 x short 1 x green
Master A/B authorised
(close programming
window)
1 x long 1 x green
Authorised medium 1 x short 1 x green
Unauthorised medium 4 x short 4 x red
Master A/B unauthorised 1 x long 1 x red
Delete subgroup with
authorised master
2 x short 1 x green Hold master medium in front
of antenna for approx. 10
seconds.
Soft INI reset with A/B
structure with authorised
programming master A or
with B structure with
programming master B
2 x short after
10 secs,
2 x short after
a further 15
secs,
Green light on
presentation
of card, goes
out upon
successful
initialisation
2 beeps after 10 seconds
confirms the complete reset
of the user media, 2 beeps
after a further 15 seconds
confirms the reset of all
master media.
Installation instructions Maintenance and troubleshooting
Kaba c-lever compact k2evo703en-2011-05 17
6 Maintenance and troubleshooting
6.1 Maintenance
The Kaba c-lever compact requires no mechanical or electronic maintenance!
6.1.1 Replacing the battery
Only a limited time is available to change the batteries without losing the
internal clock settings. This so-called residual memory time is 30 seconds for the
Kaba c-lever compact!
Rechargeable batteries must not be used as they do not have sufficient capacity.
ATTENTION
Opening the coupling unit absolves Kaba of any liability under the guarantee!
Risk of explosion
Lithium batteries can explode or burst explosively.
Improper handling of lithium batteries can lead to fires and explosions.
- Only replace lithium batteries with batteries of the same type.
- No not open, pierce or crush lithium batteries.
- Do not burn lithium batteries or expose them to high temperatures.
- Do not short-circuit lithium batteries.
- Do not recharge lithium batteries.
Detaching the lever handle
1. Detach the lever handle (5) with
the help of the dismantling key
supplied.
2. Insert the dismantling key in the
inside of the lever handle, turn
upwards and remove the handle.
5
1
Installation instructions Maintenance and troubleshooting
Kaba c-lever compact k2evo703en-2011-05 18
6.1.2 Setting the clock
The programmer is required in order to check and set the clock in the actuator.
Always check the time following a change of batteries or at least once a year. A
detailed description can be found in the Programmer user manual. It is essential
that the clock is set precisely for the system to work correctly in CardLink
authorisation mode.
6.1.3 Reading Traceback
The Traceback (event list) of the most recent 2000 events can be read using the
Programmer, provided that the function has not been previously deactivated in
the KEM software.
See Programmer user manual.
The events and data that are registered in the Traceback are listed in the kaba
evolo system description.
Taking off the housing and changing
the batteries
1. Remove the metal ring (3) with
guide ring (4) and housing (2)
from the mechatronic unit (1)
whilst pushing against the square
of the coupling unit.
2. Take out the batteries (7) and
replace them with new ones.
Ensure correct battery polarity!
3. Push the housing (2), metal ring
(3) and guide ring (4) onto the
mechatronic unit and re-fit the
lever handle.
ATTENTION
As old batteries can leak, it is advisable to check the condition of the batteries at
regular intervals. Kaba cannot provide compensation for any consequential
damage caused by faulty batteries (batteries cannot be guaranteed).
1
2 3 4
7
Installation instructions Maintenance and troubleshooting
Kaba c-lever compact k2evo703en-2011-05 19
6.1.4 Emergency opening for discharged batteries
As the batteries are accessible from the outside, no emergency opening using
the Programmer or emergency opening device is necessary. Change discharged
batteries immediately, as described in section 5.4.
- Emergency opening using locking cylinder
If all the alarms were ignored until the batteries were completely dead, the door
can only be opened from the outside using an authorised mechanical key and
the key-operated latch. To be able to open the door mechanically in an
emergency, a lock with a key operated latch must be used or fitted!
- Unlocking from the inside
1. With a panic lock, the Kaba c-lever compact can always be unlocked by
operating the handle. The relevant locking function is otherwise ensured by
moving the inner handle.
- Unlocking from the outside
1. Insert the mechanically authorised key into the locking cylinder.
2. Turn the key in the opening direction as far as the limit stop.
3. Open the door using the key-operated latch.
Installation instructions Maintenance and troubleshooting
Kaba c-lever compact k2evo703en-2011-05 20
6.2 INI reset
6.2.1 Initialising the electronic module
The electronic module can only be reset by initialising it using an authorised user
medium or programming master, i.e. the factory settings are restored.
Initialisation deletes all settings that are stored in the electronic module. !
6.3 Cleaning
The facing of the actuator may be damaged by the use of inappropriate cleaning
agents or methods.
Use a soft, damp cloth to clean the facing. Only disinfection agents that are
specifically designed for delicate metal facings and plastics should be used.
Connecting INI contacts
1. Place authorised user medium or
programming master in front of
the antenna.
2. Bridge (connect) the two
initialisation points (1) with
tweezers.
3. Successful initialisation is
confirmed by an acoustic double
signal (2 x short).
Soft INI reset
1. Hold the authorised
programming master in front of
the antenna.
2. An acoustic double signal follows
after 10 seconds.
3. Another acoustic double signal
follows after a further 15 seconds.
This confirms successful
initialisation.
Detail X
1
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
Kaba C-lever compact Installation Instructions Manual
- Type
- Installation Instructions Manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Kaba C-lever Quick Manual
-
-
-
Dormakaba E-Plex 2000 / PowerPlex 2000 Series User manual
-
Dormakaba Solitaire 850l Operating instructions
-
-
Dormakaba EX3700 User manual
-
-
-
