Sony CBK-SD01 Installation guide

Sony
Brand
Sony
Model
CBK-SD01
Type
Installation guide
SDI OUTPUT BOARD
CBK-SD01
INSTALLATION MANUAL
1st Edition
CBK-SD01
! WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
! WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
! AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
CBK-SD01
1
Table of Contents
1. Installation
1-1. CBK-SD01 Configuration ..................................................................... 1-1 (E)
1-2. Applicable Models for Installation........................................................ 1-1 (E)
1-3. Installation Procedure............................................................................ 1-1 (E)
1-4. Opening and Closing the Inside Panel .................................................. 1-2 (E)
1-5. Installing the CBK-SD01 (DIF-147 Board) .......................................... 1-3 (E)
1-6. Select Output Signal .............................................................................. 1-5 (E)
1-1 (E)
CBK-SD01
1-1. CBK-SD01 Configuration
The CBK-SD01 consists of the following:
. DIF-147 board (1)
. B2 x 4 (2)
. Precision screw P1.4 x 3.5 (2)
. Installation Guide (1)
. Installation Manual (1)
In addition to the Installation Manual, the following manuals are available.
. PDW-510/510P/530/530P Operation Manual (Supplied with PDW-510/510P/530/530P)
This manual is necessary for application and operaion of PDW-510/510P/530/530P.
Part number: 3-205-742-0X
. MSW-900/900P Operation Manual (Supplied with MSW-900/900P)
This manual is necessary for application and operaion of MSW-900/900P .
Part number: 3-206-082-0X
.
PDW-510/510P/530/530P, CBK-SD01 Maintenance Manual (Available upon request)
This manual intended for use by trained system and service engineers describes (the circuit overview,
character display functions, the main part replacements, electrical alignment, parts list, semiconductor
pin assignments, block diagrams, schematic diagrams, board layouts, etc.) required for parts-level
service.
For obtaining, contact your local Sony Sales Office/Service Center.
Part number : 9-968-032-71
1-2. Applicable Models for Installation
. PDW-510/510P/530/530P
. MSW-900/900P
1-3. Installation Procedure
Outline of the installing the CBK-SD01 to the PDW-510/510P/530/530P, MSW-900/900P is listed as
follows. For the details of the installation work, refer to the respective sections.
Installation procedure Sections describing the detailed procedure
1. Opening the Inside Panel 1-4. Opening and Closing the Inside Panel
2. Installing the CBK-SD01 (DIF-147 Board) 1-5. Installing the CBK-SD01 (DIF-147 Board)
3. Closing the Inside Panel 1-4. Opening and Closing the Inside Panel
4. Operation Check 1-6. Select Output Signal
Select the output signal with the use of menu.
Confirm that the SDI singal is output from the
VIDEO OUT terminal.
Section 1
Installation
1-2 (E)
CBK-SD01
1-4. Opening and Closing the Inside
Panel
Opening the Inside Panel
n
Be sure to turn off the POWER switch, unplug the AC
power cord or remove the battery before starting the
following procedure to prevent the inside of the unit from
damage.
1. Loosen the four screws (with drop-safe) and open the
inside panel in the direction of the arrow.
m
. Folding the flexible card wire connected to the FP-
140 board (the FP-121A board for MSW-900/900P)
shortens the life of the flexible card wire significant-
ly. Be very careful when handling the flexible card
wire not to fold it.
. To install CBK-SD01 in MSW-900/900P, place the
unit so that the inside panel is positioned on top of
the POWER switch when the inside panel is opened.
Flexible card wires
Inside panel
FP-121A board
Inside panel
Hook
Hinge
POWER switch
Hinge
Hook
Screw
(with drop-safe)
Screw (with drop-safe)
Screws
(with drop-safe)
Flexible card wires
Inside panel
FP-140 board
Hook
Hinge
Hinge
Hook
Screw
(with drop-safe)
Screw (with drop-safe)
Screws
(with drop-safe)
PDW-510/510P/530/530P is shown. MSW-900/900P is shown.
1-3 (E)
CBK-SD01
Closing the Inside Panel
1. Confirm that both of the right and left hinges are
engaged with the hooks of the chassis correctly.
2. Attach the inside panel and fix it with the four screws
(with drop-safe).
n
Standard tightening torque value :
Screw (with drop-safe, B3 x 12)
0.8 N.m (8.0 kgf.cm)
n
Be careful not to pinch the harness between the inside
panel and chassis.
1-5. Installing the CBK-SD01 (DIF-147
Board)
1. Disconnect the coaxial cable form the connector
(CN10) on the DCP-36 board (the DCP-32 board for
MSW-900/900P).
n
To disconnect the coaxial cable, do not attempt to
disconnect it by pulling the cable with force. Be sure
to hold the plug and disconnect the cable.
CN10
Coaxial cable
DCP-36 board
Hold the plug to
remove.
OK
Do not atempt to
remove by pulling
the cable.
NG
The illustration shows the PDW-510/510P/530/530P.
1-4 (E)
CBK-SD01
2. Insert the connector (CN2) of the CBK-SD01 (DIF-
147 board) to the connector (CN2) on the DCP-36
board (the DCP-32 board for MSW-900/900P) and fix
it to the supports with the two screws supplied.
n
Standard tightening torque value :
Screw P1.4 x 3.5
0.1 N.m (1.0 kgf.cm)
Screw B2 x 4
0.19 N.m (1.9 kgf.cm)
3. Connect a coaxial cable that is removed in step 1, to
the connector (CN1) on the CBK-SD01 (DIF-147
board).
CBK-SD01
Coaxial cable
CN2
CN1
CN3
DCP-32 board
Supplied screws
(P1.4 x 3.5)
Supports
CBK-SD01
CN2
CN1
Coaxial cable
DCP-36 board
Supplied screws
(B2 x 4)
Supports
CN2
PDW-510/510P/530/530P is shown. MSW-900/900P is shown.
1-5 (E)
CBK-SD01
1-6. Select Output Signal
Select the output signal following the steps as shown below.
Identifying switches
1. Turn on the main power.
2. While pressing the rotary encoder, set the MENU ON/OFF switch to ON to open the TOP
menu.
3. Select the OPERATION menu and press the rotary encoder.
4. Select the OUTPUT display and press the rotary encoder.
5. Move the cursor (→) to REAR BNC SEL and press the rotary encoder to select SDI.
6. Turn off the main power.
CANCEL/PRST
OFF
ON
ESCAPE
MENU
ON/SEL
OFF
STATUS
Rotary
encoder
STATUS ON/
SEL/OFF switch
MENU ON/OFF
switch
MENU CANCEL/PRST/
ESCAPE switch
The illustration shows the PDW-510/510P/530/530P.
CBK-SD01
The material contained in this manual consists of
information that is the property of Sony Corporation.
Sony Corporation expressly prohibits the duplication of
any portion of this manual or the use thereof for any
purpose other than the operation or maintenance of the
equipment described in this manual without the express
written permission of Sony Corporation.
Le matériel contenu dans ce manuel consiste en
informations qui sont la propriété de Sony Corporation.
Sony Corporation interdit formellement la copie de
quelque partie que ce soit de ce manuel ou son emploi
pour tout autre but que des opérations ou entretiens de
l’équipement à moins d’une permission écrite de Sony
Corporation.
Das in dieser Anleitung enthaltene Material besteht aus
Informationen, die Eigentum der Sony Corporation sind.
Die Sony Corporation untersagt ausdrücklich die
Vervielfältigung jeglicher Teile dieser Anleitung oder den
Gebrauch derselben für irgendeinen anderen Zweck als
die Bedienung oder Wartung der in dieser Anleitung
beschriebenen Ausrüstung ohne ausdrückliche
schriftliche Erlaubnis der Sony Corporation.
Printed in Japan
Sony Corporation 2004. 1 16
B&P Company ©2004
CBK-SD01 (SY) J, E
3-797-090-01
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Sony CBK-SD01 Installation guide

Sony
Brand
Sony
Model
CBK-SD01
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents