Eaton i-on16 Installation guide

Eaton
Brand
Eaton
Model
i-on16
Category
Serial switch boxes
Type
Installation guide
i-on16
Security System
Installation Guide
Issue 9
Page ii
© Eaton’s Security Business 2014
IN NO EVENT WILL EATON’S SECURITY BUSINESS BE LIABLE FOR ANY SPECIAL, CONSEQUENTIAL , OR INDIRECT LOSS OR
DAMAGE, INCIDENTAL DAMAGES, STATUTORY DAMAGES, EXEMPLARY DAMAGES, LOSS OF PROFITS, LOSS OF REVENUE,
LOSS OF ANTICIPATED SAVINGS, LOSS OF BUSINESS OR OPPORTUNTIY, LOSS OF GOODWILL OR INJURY TO
REPUTATION, LIQUIDATED DAMAGES OR LOSS OF USE, EVEN IF INFORMED OF THE POSSIBILITY OF SUCH DAMAGES.
EATON’S SECURITY BUSINESS’S LIABILITY FOR DAMAGES ARISING OUT OF OR RELATED TO A PRODUCT SHALL IN NO
CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT FROM WHICH THE CLAIM ARISES. TO THE EXTENT PERMITTED
BY APPLICABLE LAW, THESE LIMITATIONS AND EXCLUSIONS WILL APPLY WHETHER EATON’S SECURITY BUSINESS’S
LIABILITY ARISES FROM BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING BUT NOT LIMITED TO
NEGLIGENCE), STRICT LIABILITY, BY OPERATION OF LAW, OR OTHERWISE.
Every effort has been made to ensure that the contents of this book are correct. The contents of this book
are subject to change without notice.
This manual applies to i-on16 control units with version 4.04 software. Please note that i-on16 control unit
software cannot be updated.
For Your Safety
This book contains several passages alerting you to potential problems or hazards. Each of these are
marked by the words Note, Caution or WARNING.:
Note:
Describes conditions that may affect the proper functioning of the equipment (but will not
damage the equipment).
Caution:
Describes actions that will physically damage the equipment and prevent its proper
function.
WARNING:
Describes actions that are hazardous to health, or cause injury or death.
Please pay particular attention to these marked passages.
Other Publications for the i-on16:
The following guides are available from the Eaton’s Security Business website: www.coopersecurity.co.uk
Quick User Guide
Brief instructions for setting and unsetting alarm systems based on i-
on control units.
i-on Range Engineering Guide
A detailed description of the Installer’s programming options
available for i-on control units.
i-on16 Administrator’s Guide
Detailed notes for the system administrator of an alarm system
based on the i-on16.
i-on16
Page iii
Contents
1. Introduction ....................................................... 1
Overview ............................................................. 1
Installer Programming Interface ..................... 1
About this Guide ............................................ 1
2. Before You Begin .............................................. 2
Preparation ......................................................... 2
Radio Site Survey .......................................... 2
Siting the Control Unit .................................... 2
Siting Keypads ............................................... 2
Guided Tour ........................................................ 2
Opening the End Station Case ...................... 2
End Station PCB ............................................ 3
Keypads ......................................................... 3
Power Availability ............................................... 6
Keypad Cabling Requirements ........................... 7
3. Installation ......................................................... 8
Tools Required ................................................... 8
Step 1. Fit the Control Unit Box .......................... 8
Fitting ............................................................. 8
Step 2. Fit and Connect the Keypad(s) .............. 8
Siting the Keypad(s) ....................................... 9
Fitting Keypads .............................................. 9
Connecting Keypads to Control Unit .............. 9
Keypad Connection ........................................ 9
Keypad Addressing ...................................... 10
Re-using a V2.0 Keypad From an i-onEX .... 10
Backlight Control i-kp01 ............................... 10
Backlight Control for KEY-K01/KP01/KPZ01 10
Tone Volume – All Keypads......................... 13
Connecting Wired Zones (KEY-KPZ01 only) 13
Step 3. Connect End Station to Mains ............. 13
Mains Cabling .............................................. 13
Mains Connection ........................................ 14
Step 4. Connect Wired Peripherals .................. 14
Remote Loudspeaker (Optional) .................. 14
Wired External Sounders (Optional) ............ 14
Wired Outputs (Optional) ............................. 14
Fit and connect the I-RC01 (Optional) ......... 14
Output on KEY-KPZ01 ................................. 15
Step 5. Fit and Connect I-SD01 (Optional) ...... 15
Safety Notice ................................................ 15
Removing an I-SD01 .................................... 16
Step 6. Fit and Connect Battery ....................... 16
Programming a Control Unit Before Installation
..................................................................... 16
Step 7. Initial Power-Up .................................... 16
Step 8. Commission the System ...................... 17
4. Programming .................................................. 18
Re-Entering the Installer Menu .................... 18
Leaving the Installer Menu ........................... 18
Important! Saving Changes .............................. 18
Restoring the Access Codes (1
st
stage Reset) 18
Restoring All Factory Default Programming ..... 19
Learning radio detectors ................................... 19
Installer Menu ................................................... 20
5. Maintenance .................................................... 21
6. Technical Specification .................................. 22
Specification ..................................................... 22
General ........................................................ 22
Security ........................................................ 22
Radio ............................................................ 22
Communications .......................................... 22
Power Supply ............................................... 22
Electromagnetic Compatibility ...................... 23
Outputs ......................................................... 23
Fuses ........................................................... 23
Electrical Safety ........................................... 23
Compliance Statements ............................... 23
Compatible Equipment ..................................... 23
HUD ............................................................. 23
Detectors ...................................................... 23
Sounders ...................................................... 23
Setting / Unsetting – Keypads ...................... 23
Setting / Unsetting - Fobs ............................ 23
Communicators ............................................ 23
Accessories .................................................. 23
Appendix I. Recording Speech Messages ....... 24
i-on16
Page iv
This page is intentionally blank.
i-on16
Page 1
1. Introduction
Overview
The i-on16 is the control unit for a wirefree alarm
system intended for domestic and light commercial
use.
The control unit comprises an end station and
separate keypad.
The end station has an ABS plastic case which
contains the radio transceiver, power supply and
backup battery. Connected to the end station by
standard alarm cable is the keypad.
The i-on16 at release 4 uses i-kp01 keypads with
software revision 2.0 onwards. The keypad allows
the end user to set and unset the system, and the
installer to configure the control unit. The keypad
also contains an integral proximity tag reader,
allowing end users to control the system without
having to remember access codes.
Note that to work correctly the i-on16 must be fitted
with at least one wired keypad.
There are three other types of keypad available for
connection to the i-on16:
KEY-K01
This keypad has no internal prox
reader, and is supplied in a square
format case.
This product, supplied in the same
case as the KEY-K01, has an
internal prox reader and also
provides terminals for an external
prox reader KEY-EP
KEY-KPZ01
This product, supplied in the same
case as the KEY-K01, has an
internal prox reader and also
provides terminals for up to two
zones, a programmable output, and
an external prox reader KEY-EP
A range of wireless peripherals is available for
operation with the control unit. These include a door
contact/universal transmitter, a passive infra red
detector, smoke detector, external siren, 4 button
remote control, and remote radio keypad.
The control unit supports 16 wirefree alarm zones, 4
hardwired transistor outputs, 16 four button remote
controls, 16 two button hold up alarm, and 16 users.
When fitted with an optional plug on module the
control unit can send recorded speech messages
over the public switched telephone network (PSTN).
The module can also report alarm information using
standard protocols such as Fast Format, SIA and
Contact ID.
This manual shows the simple procedure required
to install the control unit and its keypad. When you
have completed the physical installation please
consult the Programming section for details of
configuring the system to meet your exact
requirements.
Installer Programming Interface
Once fitted and powered up, you can program the
control unit through any wired keypad connected to
the control unit. The Installer Menu allows you to
specify all the operating parameters for an
individual installation.
In addition, it is possible to connect a PC or laptop
to the mini USB port on the control unit PCB and
use Eaton’s Security Business’s Downloader
software to program the control unit.
Note: Some programming options can make the
installation non-compliant with EN50131. The
relevant options are noted in the “Installer Menu”
section of the i-on Range Engineering Guide.
About this Guide
This guide shows the simple procedure required to
physically install the control unit, connect keypads,
expanders and power supplies and power up the
system for the first time.
When you have completed the physical installation
please consult the i-on Range Engineering Guide
for details of configuring the system to meet your
customer’s requirements. For your convenience
page 20 of this installation guide contains a
condensed reference table of the Installer menu.
i-on16
Page 2
2. Before You Begin
Preparation
Before installation you should carry out a survey of
the site. You need to know how many and what kind
of detectors will be transmitting to the control unit.
You also need to assess where the control unit
must be placed in order to receive radio signals
from the detectors successfully.
Radio Site Survey
You should conduct signal strength tests before
installation. Eaton’s Security Business produce the
Scantronic 790r hand held signal strength meter
and 734r-01 test transmitter for this purpose. Please
read the 790r manual for details.
Please be aware of the following:
The 790r signal strength meter readings should
be used only as an guide when initially checking
the site.
A reading of four green LEDs or higher
indicates an acceptable signal strength.
Once you have installed the alarm system you
should put the control unit in the Installer test
menu and test the received signal strength from
each radio transmitter.
A signal strength reading of two or more units
by the control unit from each transmitter should
provide reliable operation in the installed
system. (Note: if you take the signal strength
using Downloader or the web server while the
panel is in user mode then the minimum
acceptable signal strength is four units. Ensure
that the control unit is in Installer mode when
reading signal strengths remotely.)
When you record the signal strength readings
for later inspection, you should record the
readings taken from the control unit of the
installed system while it is in the Installer Menu.
Please be aware that the signal strength received
from a transmitter can change after installation
because of local environmental changes. For
example, users switching on laptops nearby, or
moving metal cabinets from their original position
can all affect the signal from a transmitter. Please
read Eaton’s Security Business publication
”Guidance Notes for Wireless Alarm System
Installations” obtainable from
www.coopersecurity.co.uk for more information
about the factors affection radio signal strength.
Siting the Control Unit
Do site the unit:
Upright (battery at the bottom).
Within a protected zone.
As high as possible. However, do make sure
that the unit is on a similar level to the other
transmitters or receivers.
Do NOT site the Control Unit:
In the entry or exit zones, or outside the area
covered by the alarm system.
Close to or on large metal structures.
Closer than one metre to mains wiring, metal
water or gas pipes, or other metal surfaces.
Lower than two metres from the floor (ideally).
Inside metal enclosures.
Next to electronic equipment, particularly
computers, photocopiers or other radio
equipment, CAT 5 data lines or industrial mains
equipment.
Note: Some window glasses, especially those sold
as “insulating” or “energy conserving” may be
coated with thin metal or conducting films. These
glasses are particularly poor at transmitting radio
waves.
Siting Keypads
Do site the keypad:
Within the area protected by the alarm system.
At a convenient height and location for the user.
Out of sight of potential intruders.
Do NOT site the keypad:
Next to electronic equipment, particularly
computers, photocopiers or other radio
equipment, CAT 5 data lines or industrial mains
equipment.
Where the cable run from the end station will be
longer than 100m.
If fitting two or more keypads make sure that you
place the keypads more than one metre apart from
each other, or from any other type of prox reader.
(At less than one meter separation the proximity tag
readers will interfere with each other.) Remember
not to place keypads or external prox readers on
opposite sides of the same wall.
If you intend to fit external prox reader KEY-EP to a
KEY-KPZ01/KP01, then do not site the external
prox reader itself closer than one meter to any other
keypad or other type of prox reader.
Guided Tour
Opening the End Station Case
WARNING: When connected to the mains with
power applied mains voltages are present on the
shrouded heads of the terminal screws of the mains
connector (“7” in figure 2).
Caution: Static Electricity. Like many other
electronic products, the control unit contains
components that are sensitive to static electricity.
Try not to handle the PCB directly. If you must
i-on16 Before You Begin
Page 3
handle the PCB, take the standard precautions
against damage by static electricity.
To gain access to the interior of the end station
undo the two screws at the top of the case. Pull the
top of the lid down, and then lift the lid out of the
retaining lugs at the bottom of the case (see Figure
1.)
Figure 2 shows the interior of the end station.
Figure
1.
Opening the Control Unit
1. Central fixing keyhole.
2. Aerials.
3. Fixing holes.
4. Printed circuit board (PCB).
5. Cable entry holes for PCB.
6. Transformer.
7. Mains connector block.
8. Cable entry hole for mains.
9. Back Tamper switch (if fitted).
10. Connector pins for Lid Tamper.
Figure
2.
Control Unit
End Station PCB
Figure 3 shows the controls and connectors
available on the end station PCB.
1. Aerials.
2. 20VAC Input (from transformer).
3. Battery input (12VDC).
4. Kick start pins.
5. Connector block.
6. Reset codes pins.
7. Holes for module support pillars.
8. RF receiver.
9. “Heartbeat” LED.
10. Connector pins for tamper switch.
11. Sockets for communicator (I-SD01).
Figure
3.
End Station Printed Circuit Board
Keypads
i-kp01 Controls and Displays
1. LCD display (2 x 20 characters).
2. Programming keys.
3. Navigation keys
4. Alert LEDs
5. Setting and unsetting keys.
6. Programmable HUA keys.
7. Number/text keys.
8. Set/Unset LEDs.
Figure
4.
Controls and Displays
1
2
3
1
3
4
5
6
7
3
9
3
8
2
2
10
0V 0V 12V 12V0V 12V A B0V 12V 1 2 3 4
TR14V4 - LS +
AUX AUXBUSAUX OUTPUTS
2
3
5
9
11
8
6
7
11
4
10
2
3
4
6
5
8
7
1
Before You Begin i-on16
Page 4
Opening the i-kp01 Keypad
Note: For EN50131-3:2009, 8.7 the keypad is a
type B ACE, fixed.
To open the keypad first gently prise off the trim on
the front and remove the two screws. Next, carefully
lever the front of the keypad (containing the PCB
and display) away from the keypad rear housing.
Figure
5.
Opening the Keypad
1. Central keyhole.
2. Rear tamper shroud.
3. Cable entry.
4. Fixing holes.
Figure
6.
Keypad Rear Housing
1. Sounder.
2. Sounder volume control.
3. Tamper switch.
4. a) Address Jumpers
b) Jumpers for LED function:
5. RS485 termination jumper
6. Connector for control unit.
Figure
7.
Keypad PCB
1
2
3
4
2
4
3
3
1
i-on16 Before You Begin
Page 5
KEY-K01/KP01/KPZ01 Controls and Displays
1. LCD display
2. Programming keys.
3. Navigation keys. This key has built-in alert
LEDs.
4. Setting and unsetting keys. The ABCD keys
have built-in status LEDs that can show the
setting status of a part setting system. These
LEDs can be disabled, see page 10.
5. Plastic caps covering screws (shown closed
and open).
6. Hold Up Alarm (HUA) keys.
7. Number/text keys.
Figure
8.
KEY-K01/KP01/KPZ01 Controls and
Displays
Opening the KEY-K01/KP01/KPZ01
To open the unit, unclip the caps covering the
screws on the front. (You may need to gently push
the bottom edge of the caps in with the end of a
small screwdriver to start them.) Remove the two
screws hidden underneath (see Figure 8). Gently
swing the lower side of the front out from the back
box by about 10mm and then slide the front
upwards to disengage the top catches. (Be careful
not to pull the lower side of the front more than
about 25mm away from the back while the top
catches are engaged, or you may break the
catches.)
Figure
9.
Opening the Keypad
1. Central keyhole.
2. Fixing holes.
3. Cable entry.
4. Tamper block
Figure
10.
Keypad Rear Housing
1. Jumpers for addressing and LED function:
1a Addressing (not used for i-onEX)
1b LED functions and RS485 bus termination.
2. Sounder volume control.
3. Tamper switch.
4. Sounder.
5. Connector for control unit.
Figure
11.
KEY-K01 Keypad PCB
2
3
65 5
4
7
1
1
2
3
Before You Begin i-on16
Page 6
1. Tamper switch.
2. Sounder.
3. Connector for KEY-EP.
4. Sounder volume control.
5. Connector for control unit bus.
6. Jumpers for:
6a Addressing (not used in i-onEX control
units).
6b LED functions and RS485 bus
termination.
Figure
12.
KEY-KP01 Keypad PCB
1. Tamper switch.
2. Sounder.
3. Connector for KEY-EP. Terminals for zones
4. Sounder volume control
5. Connector for data bus and output terminal.
6. Jumpers for addressing and LED function:
6a Addressing
6b LED functions and RS485 bus
termination.
Figure
13.
KEY-KPZ01 Keypad PCB
Power Availability
Before connecting any external devices to the
control unit, you must make sure that the control
unit can provide sufficient current to power the
system during a mains failure for the time required
to meet Grade 2 PD6662 or EN50131-1. The
standard requires 12 hour standby, which includes
two periods of 15 mins in alarm.
The amount of current available from the control
unit depends on the battery fitted. The current taken
by the control unit PCB, communicator and keypads
is given in Technical Specifications on page 22.
For example: in an alarm system with an i-on16
control unit and two i-kp01 keypads the system
takes the following total quiescent current:
Device
Current
Control unit PCB
130mA
i-sd01 communicator (quiescent)
20mA
2 x i-kp01 at 30mA each
(backlights off)
60mA
Siren (quiescent)
25mA
Total
235mA
During an alarm, these figures become:
Device
Current
Control unit PCB
220mA
i-sd01 communicator
50mA
2 x i-kp01 at 30mA each
(backlights off)
60mA
Ext Siren & Strobe
400mA
Total
730mA
The total amp hours required =
(0.235A x 11.5h) + (0.730A x 0.5h) = 3.07Ah
A fully charged 7Ah battery can provide this amount
of charge.
In this example a 7Ah battery should exceed the
Grade 2 requirements.
Note: All current drawn from the Aux terminals (12V
and 14.4V) must be included in the overall
calculation.
2
3
4
BRIGHT
TERM
0V 12V A B
0V 12V D0 D1 LED
EXT READER
Z1 Z2
OP
1
6a
6b
3
4
5
6
2
i-on16 Before You Begin
Page 7
Keypad Cabling
Requirements
Cable Type
In general, the control unit requires standard 7/0.2
un-screened alarm cable for wiring to keypads.
Screened cable may prove necessary if the
installation site has equipment that produces high
levels of R.F. (Radio Frequencies), for example
welding equipment. If screened cable is required,
you should keep to the following guidelines:
1. Avoid earth loops by connecting the screen on
the cable to mains earth at the end station but
not at the keypad.
2. The continuity of the cable screen is most
important and screens MUST be continuous
along the full length of the cable.
3. If the cable enters any metal enclosure, ensure
the screen is isolated from the case.
Cable Segregation
Segregate the keypad cabling from any other
wiring, such as mains supply cables, telephone
cables, computer network cables and R.F. cables.
Use cable ties to keep cables separated.
Keep the keypad cable clear of cables supplying
sounders or extension loudspeakers.
Cable Configuration and Length
You can connect up to two keypads to the end
station. You may connect the keypads either
serially, or in parallel at the end station connector.
The cable length from control unit to the most
distant keypad should not exceed 100m.
i-on16
Page 8
3. Installation
Exposure to Radio Frequency Radiation:
The radiated output power of this device is below
those levels considered safe by European exposure
limits. Nevertheless, when fitting the product place it
in such a manner as to minimise the potential for
human contact during normal operation. To
minimise exposure, users should be more than 200
mm from the device during normal operation
Caution: Static Electricity
Like many other electronic products, the control unit
and keypads contain components that are sensitive
to static electricity. Try not to handle their PCBs
directly. If you must handle a PCB, take the
standard precautions against damage by static
electricity.
Tools Required
790r signal strength meter and 734r test transmitter.
Flat screwdriver (small).
Philips screwdriver.
Drill.
5mm drill bit.
M5 36mm (four off) and 25mm screws (three off).
Wallplugs, filler.
Step 1. Fit the Control Unit
Box
Caution: Static Electricity Like many other
electronic products, the control unit contains
components that are sensitive to static electricity.
Try not handle the PCB directly. If you must handle
the PCB, take the standard precautions against
damage by static electricity.
Fitting
Note: Please read the advice on siting the control
unit on page 2.
To prevent access to the inside of the control unit,
you must mount the back of the control unit on a
wall, using at least four fixing holes. Use an
No10/M5 countersunk screw at least 36mm long.
Figure 14 shows the fixing holes and cable entries.
Protect the unit from dust and drilling debris when
drilling the fixing holes.
1. Fixing holes.
2. Cable entries.
Figure
14.
Fixing Holes and Cable Entries
Installing the Lid/Back Tamper
Fit and connect the combined lid/back tamper
(provided). Ensure that the switch is oriented as
shown in Figure 15.
Figure
15.
Lid/Back Tamper
Item 10 in Figure 3 shows the connector for the
lid/back tamper.
Step 2. Fit and Connect the
Keypad(s)
Note: If you are installing a keypad that was
previously used on an i-onEX system, then make
sure you default the keypad address BEFORE
attaching it to the i-on16. See page 10 for detailed
instructions.
1
1
2
1
1
2
i-on16 Installation
Page 9
Siting the Keypad(s)
Do site the keypad(s):
Within the area protected by the alarm system.
At a convenient height and location for the user.
Out of sight of potential intruders.
Do NOT site the keypad(s):
Next to electronic equipment, particularly
computers, photocopiers or other radio
equipment, CAT 5 data lines or industrial mains
equipment.
Where the cable run from the control unit will be
longer than 100m (see Cable Configuration and
Length).
Note: Do not fit any keypad with an internal prox
reader closer than one meter to any other type of
prox reader. This includes other keypads with prox
readers, external prox readers such as the KEY-EP,
or prox readers used by other systems (for example
access control systems). If you mount prox readers
closer together than one meter (including on the
other side of walls) then the two prox readers will
interfere and may not work correctly.
Fitting Keypads
Select which cable entry you are going to use and
break out the appropriate plastic sections.
Use 4mm x 25mm countersunk screws with a
thread suitable for the wall material in at least three
fixing holes when mounting the back of the keypad
on the wall.
i-KP01
If required, drill out the hole for the back tamper
using a 7mm bit (see Figure 16).
Figure
16.
Screw i-KP01 Back Box to Wall
KEY-K01/KP01/KPZ01
Make sure the backplate is level and mark, drill and
plug at least three fixing holes. Screw the backplate
to the wall through the fixing holes using the M4
screws.
Figure
17.
Screw KEY-K01/KP01/KPZ01 Back Box
to Wall
Connecting Keypads to Control Unit
Cable Type
In general, the control unit requires standard 7/0.2
un-screened alarm cable for wiring to keypads.
Screened cable may prove necessary if the
installation site has equipment that produces high
levels of R.F. (Radio Frequencies), for example
welding equipment. If screened cable is required,
you should keep to the following guidelines:
1. Avoid earth loops by connecting the screen on
the cable to mains earth at the end station but
not at the keypad.
2. The continuity of the cable screen is most
important and screens MUST be continuous
along the full length of the cable.
3. If the cable enters any metal enclosure, ensure
the screen is isolated from the case.
Cable Segregation
Segregate the keypad cabling from any other
wiring, such as mains supply cables, telephone
cables, computer network cables and R.F. cables.
Use cable ties to keep cables separated.
Keep the keypad cable clear of cables supplying
sounders or extension loudspeakers.
Cable Configuration and Length
You can connect up to two keypads to the end
station. You may connect the keypads either
serially, or in parallel at the end station connector.
The cable length from control unit to the most
distant keypad should not exceed 100m.
Keypad Connection
Figure 18 shows the wiring connections at the
keypad and control unit.
Installation i-on16
Page 10
Figure
18.
Connecting a Keypad to the Bus
Keypad Addressing
Each keypad connected to an end station must
have a unique address. See Figure 7 on page 4 for
the position of the addressing jumpers. Do not fit
links to jumpers 3 or 4.
Figure
19.
Keypad Addressing Jumpers
To add a new wired keypad to the bus of an existing
i-on16 installation, first remove all power from the
control unit, both mains and battery. Make sure the
address link on the new keypad is not fitted in the
same position as the address links on the keypad
already connected to the control unit. Connect the
new keypad and then apply power to the system.
Re-using a V2.0 Keypad From an i-onEX
If you wish to use an i-kp01 that has previously
been working on an i-onEX system, then you must
first default the keypad address. Eaton’s Security
Business recommend that you do this by deleting
the keypad from the i-onEX system using the
Installer Menu. However, if this is not possible then
you must default the keypad address manually as
follows:
1. Remove the power and data connections from
the keypad to the system bus.
2 Open the keypad and make sure that the
keypad tamper switch is open. (It must stay
open until step 9.)
3. Apply 12Vdc power to the 0V and 12V terminals
on the keypad connector. DO NOT use the i-
on16 bus for this.
The navigation key LEDs flash rapidly.
4. Hold down keys D and at the same time.
After a few seconds you should hear a
confirmation tone and the navigation LEDs start
flashing about once per second.
5. Release the D and keys.
6. Remove the 12V dc power from the keypad.
7. Select an address for the keypad by placing a
jumper on the appropriate address pins (see
Figure 19).
8. Connect the new keypad (see Figure 18).
9. Close the keypad and ensure that the tamper
switch is closed.
Backlight Control i-kp01
You can control the appearance of the keypad
backlights and set/unset LEDs by fitting links over
the appropriate jumpers on the keypad PCB (see
Figure 7 on page 4 for the position of the jumpers).
The jumpers have the following functions:
The set/unset LEDs
are disabled.
The set/unset LEDs
shows the setting
status of the system.
(Full set is the left
hand LED.) See Note.
The key backlights are
disabled. They will
glow briefly for five
seconds when a user
presses a key.
The key backlights
glow all the time at
normal intensity.
The keypad backlights
glow all the time, extra
bright.
Note: To comply with PD6662:2010 at Grade 2,
disable the ABCD LEDs.
Backlight Control for KEY-K01/KP01/KPZ01
You can control the brightness of the keypad
backlights by fitting links over the BRIGHT jumper
on the keypad pcb (see 1b in Figure 11 or 6b in
Figure 13).
Jumper OFF The keypad backlights glow at
normal intensity.
Jumper ON The keypad backlights glow extra
bright.
Programming Backlight, ABCD LEDs and
Navigation LEDs From the Keypad
You can set the function of the backlights in either
of two ways:
a) Use the Installer Menu – Detectors/Devices – Wired
Keypads – Edit Keypad – (Keypad n) – Backlight option.
See the Engineering Guide for more details.
4
3
2
4
3
2
4
3
2
4
3
2
ON
BRIGHT
BL
ABCD-ON
ON
BRIGHT
BL
ON
BRIGHT
BL
ABCD-ON
ON
BRIGHT
BL
ABCD-ON
ON
BRIGHT
BL
ON
BRIGHT
BL
ABCD-ON
ON
BRIGHT
BACKLIGHT
BACKLIGHT
BACKLIGHT
ABCD-ON
ON
BRIGHT
ON
BRIGHT
ABCD-ON
ON
BRIGHT
BACKLIGHT
BACKLIGHT
BACKLIGHT
ABCD-ON
ON
BRIGHT
ON
BRIGHT
ABCD-ON
ON
BRIGHT
BACKLIGHT
BACKLIGHT
BACKLIGHT
ABCD-ON
ON
BRIGHT
ON
BRIGHT
ABCD-ON
i-on16 Installation
Page 11
b) Enter a local keypad programming mode (this
replaces the use of jumpers on the keypad PCB in
the i-kp01).
In addition, the local keypad programming mode
allows you to enable or disable the LEDs in the
ABCD keys and the Navigation key.
It is possible to enter keypad programming mode
when the keypad is not connected to a control unit,
but simply powered by 12VDC connected to the
keypad bus terminal (see Figures 11 and 13). If the
keypad IS connected to a control unit then make
sure that the control unit is in Installer Menu before
entering the keypad’s local programming mode.
Entering Local Programming Mode
1. Apply 12Vdc to the keypad.
2. Enter Installer Menu on the
control unit, if the
keypad is connected to a
system.
3. Open the keypad tamper.
4. Press and hold down B and
together for at
least two seconds.
The keypad is now in local
programming mode,
the display shows the
current status.
MENU
To Switch ABCD LEDs ON or OFF
1. Enter local programming
mode (see above).
MENU
2. Press or to enable or
disable the ABCD LEDs.
The character at the right of
the display shows “” when
the LEDs are disabled and
“” when the
LEDs are enabled. For
example:
MENU
3. Leave local programming
mode and save your
changes (see page 11).
To Change Backlight Settings
1. Enter Local Programming
mode (see above)
MENU
2. Press . The display
shows the current status of
the backlight LEDs, for
example:
MENU
3. Press repeatedly to
select one of the following:
Backlight LEDs ON ().
MENU
Backlight timed ().
The backlight will glow for
12 seconds after the last
keypress. The action of
the backlight depends on
the programming of the
control unit (which must
have Release 3 software
or higher installed).
MENU
4. Leave local programming
mode and save your
changes (see below).
To Disable/Enable the Status OK LED
1. Enter Local Programming
mode.
MENU
ABCD
2. Press repeatedly until
the display shows:
MENU
STATUS OK LED
3. Press repeatedly to
select one of the
following:
Status OK LED ON ().
MENU
STATUS OK LED
Status OK LED OFF ().
The green status LED
under the navigation key
will glow for 20 seconds
after the last press (this
may be useful when the
keypad is placed in
bedrooms that should be
completely dark at night).
MENU
STATUS OK LED
4. Leave local programming
mode and save your
changes.
To Disable/Enable the Status Fault LED
1. Enter Local Programming
mode.
MENU
ABCD
2. Press repeatedly until
the display shows:
MENU
STATUS FLT LED
3. Press repeatedly to
select one of the
following:
Status Fault LED ON ().
MENU
STATUS FLT LED
Status Fault LED OFF
().
The red Fault LED under
the navigation key is
disabled, and will not
glow for any fault reports.
MENU
STATUS FLT LED
4. Leave local programming
mode and save your
changes (see below).
Installation i-on16
Page 12
To Leave Local Programming Mode and
Save Changes
EITHER:
Press
OR
Close the keypad tamper.
The keypad saves the changes you have made in
its local memory.
You can now remove 12Vdc power, if required, or
leave Installer Menu on the control unit.
KEY-EP External Prox Reader
Figure 20 shows the outside details of the external
prox reader KEY-EP:
1. LED window.
2. Retaining Screw.
3. Removable Fixing Plate.
4. Permanently attached cable.
Figure
20.
External Prox Reader KEY-EP
Siting the External Prox Reader
Do site the External Prox Reader:
At a convenient height and location for the user.
Out of sight of potential intruders.
Note that the external prox reader is fitted with a
length of 2m of the appropriate cable. The cable
can be extended up to 50m by connecting an
additional length of 7/0.2 un-screened alarm
cable.
Do NOT site the External Prox Reader:
Next to electronic equipment, particularly
computers, photocopiers or other radio
equipment, CAT 5 data lines or industrial mains
equipment.
Note: Do not site the external prox reader closer
than one meter to any other kind of prox reader (for
example an i-kp01, KEY-KP01/KPZ01 or another
external prox reader). If you do so then the prox
readers will interfere and be unable to read tags.
Opening the External Prox Reader
To open the external prox reader (see Figure 21):
1. Undo the single retaining screw.
2. Tilt the edge of the fixing plate and then slide it
a short distance parallel to the body of the prox
reader.
3. Slide the fixing plate away from the reader
body, along the cable.
Figure
21.
Opening External Prox Reader
Figure 22 shows the details of the external prox
reader backplate:
1. Fixing hole.
2. Cable entry.
3. Anchor for retaining screw.
Figure
22.
External Prox Reader Fixing Plate
Fit External Prox Reader
Use M4 25mm countersunk screws at both fixing
holes when mounting the back of the keypad on the
wall. Ensure the screw has a thread suitable for the
wall material.
Connecting Remote Prox Reader to
Keypad
Segregate the external prox reader cable from any
other wiring such as mains supply cables,
telephone cables, computer network cables and
R.F. cables. Use cable ties to keep cables
separated.
2
3
4
1
1
1
2
3
i-on16 Installation
Page 13
Keep the prox reader cable clear of cables
supplying sounders or extension loudspeakers.
Figure 23 shows the wiring connections at the
keypad.
Figure
23.
Connecting the External Prox Reader
Tone Volume – All Keypads
To adjust the volume of tones from the keypad:
Louder
Note: This control changes the
volume of non-alarm tones (for
example Exit/Entry tone). The
volume of alarm tones is fixed.
Softer
Figure
24.
Adjusting Keypad Volume.
Connecting Wired Zones (KEY-KPZ01 only)
The KEY-KPZ01 provides terminals for up to two
zones. You must enable the zones from the Installer
Menu – Detectors/Devices – Wired Keypads – Edit
Keypad (keypad number) – Zones.
Once the zones are enabled they occupy the zone
numbers at the top of the numbering range,
depending on the address of the keypad.
Keypad zone
Panel zone
FSL
Panel Zone
CCL
Keypad 1 Zone 1
15
15 Alarm
Keypad 1 Zone 2
16
15 Tamper
Keypad 2 Zone 1
13
13 Alarm
Keypad 2 Zone 2
14
13 Tamper
To select the wiring type for the keypad zones use
Installer Menu - System Options - Wired Zone Type – All
Zones. Alternatively, to select the wiring type for an
individual keypad, use Installer Menu –
Detectors/Devices – Wired Keypads – Edit Keypad
(keypad number) – Wired Zone Type.
Figure 25 shows the wiring connections for FSL
zones on a KEY-KPZ01. Note that the resistance
values shows are examples.
Figure
25.
Wiring FSL Zones on KEY-KPZ01
Figure 26 shows the wiring connections for Closed
Circuit Loop connections to the zones on a KEY-
KPZ01,
Figure
26.
KEY-KPZ01 CCL Zone Wiring
Step 3. Connect End Station
to Mains
WARNING: ENSURE THAT THE MAIN SUPPLY IS
DISCONNECTED AND ISOLATED BEFORE
MAKING ANY MAINS CONNECTIONS. All mains
electrical connections must be carried out by a
qualified electrician and must comply with the
current local regulations (e.g. IEE).
Mains Cabling
Make sure that the mains supply cable does not run
vertically behind the aerials within the end station
case.
Figure
27.
Mains Cabling
KEY-KPZ01
Zone 0
Zone 1
2K2 EOL
4K7
Alarm contacts
Tamper contacts
2K2 EOL
4K7
Alarm contacts
Tamper contacts
100 Ohms
Tamper Zone 1
Alarm Zone 1
KEY-KPZ01
>1m >1m
Installation i-on16
Page 14
If you wish run mains cable through the side of the
case, make sure that they are horizontal for the last
metre before entering the case.
Mains Connection
Figure 28 shows the mains connection. Connect to
a suitable supply using a double pole disconnect
(isolation) device in accordance with EN60950-1.
Figure
28.
Mains Connection
Caution: Do not apply power at this point.
Step 4. Connect Wired
Peripherals
The end station PCB provides four connectors for
wired outputs. Each of these outputs is driven by a
transistor, and is capable of sinking a maximum
500mA when active. The outputs are 0V when
active, +12V when inactive.
Figure 29 shows examples of connecting wired
peripherals.
Figure
29.
Connecting Wired Peripherals
Remote Loudspeaker (Optional)
If you wish to add a wired Loudspeaker unit, then
connect it as shown in Figure 29.
Wired External Sounders (Optional)
Wired external sounders differ in their methods of
connection. Figure 29 shows an example of a
general method of using the outputs to connect a
wired sounder.
It is possible to program the TR terminal on the
control unit (see Figure 3) as either CC or FSL. Use
Installer Menu – System Options – Panel Tamper Rtn.
By default the terminal is CC. If you program the TR
terminal as FSL then make sure you connect a 2k2
resistor in series with the wire to the sounder.
Note: If you do not wish to connect a wired external
sounder then leave TR programmed as CC and
make sure you link TR to 0V on the control unit.
This prevents the control unit reporting Bell Tamper
unnecessarily.
Wired Outputs (Optional)
Figure 29 shows an example of using the wired
outputs to drive an indicator LED.
Fit and connect the I-RC01 (Optional)
Eaton’s Security Business provides the I-RC01
relay card for use when connecting the outputs to
devices that require voltage free contacts on their
inputs. The I-RC01 is supplied with a short wiring
loom that provides connections to each relay trigger
input (see Figure 30). A single wire allows you to
connect the module to the 12V +ve aux supply in
order to provide power for all four relays. The
terminals on the edge of the card provide
connections to the Normally Open, Common and
Normally Closed terminals of the relays.
1. Brown - OP1
4. Blue – OP4
2. Orange - OP2
5. Red - 12V +ve
3. Yellow - OP3
Figure
30.
Connecting an I-RC01 Module
Once you have connected the wiring loom of the I-
RC01 to the control unit output terminals then slide
I-RC01 PCB into one of the two slots provides at
the side of the control unit case.
L
N
T 250mA 250V
230V ~50Hz 170mA
0V 0V 12V 12V0V 12V A B0V 12V 1 2 3 4
TR14V4 - LS +
AUX AUXBUSAUX OUTPUTS
+LS
-LS
12V +
0V
Tamper In
Tamper Out
Strobe +ve
Strobe -ve
Trigger -v e
OP1 OP2 OP3 OP4
NO NCC
1
2
3
4
5
I-ON16
I-RC01
0V 12V 1 2 3 4 TR14V4 - LS +
AUX OUTPUTS
i-on16 Installation
Page 15
Figure
31.
Inserting I-RC01 Module
Output on KEY-KPZ01
The output on any KEY-KPZ01 is not available for
use with an i-on16.
Step 5. Fit and Connect I-
SD01 (Optional)
Safety Notice
Figure 32 identifies connectors for Safety Extra-Low
Voltage (SELV) and Telecommunications Network
Voltage (TNV) circuits on the control unit's main
PCB. These terms are used in accordance with the
definitions in Safety Standard EN60 950.
The Installer must ensure that TNV terminals are
connected only to other circuits designated as TNV
circuits (for example, the PTSN) and that SELV
terminals are connected only to other circuits
designated as SELV circuits. Strict adherence to the
installation instructions will ensure that the
equipment continues to comply with the safety
regulations to which it was approved.
1. SELV terminals
2. TNV terminals.
Figure
32.
SELV and TNV Terminals
CAUTION: Make sure that the end station is not
powered (either mains or battery) before fitting the I-
SD01.
Before fitting the I-SD01 module, check whether the
telephone line you intend to use is shared with an
ADSL (broadband) modem. If it is, then remove the
factory fitted jumpers from the SD01 and fit filter
ADSL01 as shown in Figure 33 .
Figure
33.
Fitting ADSL01 to I-SD01
Note: If you are not fitting an ADSL01 then leave
the factory fitted jumpers in place.
Fit the I-SD01 to the plug on module sockets (see
11 on Figure 3).
Figure
34.
Fitting I-SD01 Module
The person connecting the I-SD01 module to the
PSTN must be suitably qualified. Connect the I-
SD01 telephone connector (see Figure 35) ONLY to
the PSTN or to other circuits designated as
Telecommunications Network Voltage.
1
2
ADSL01
Installation i-on16
Page 16
WARNING: Telecommunications Network
Voltage
A, B Connect to PSTN
A1, B1 Connect to local phone extension (if
required)
E For added surge protection connect to
a suitable protective earth.
C Note: On UK pulse dialling lines
connect to ringing wire from PSTN
and to ringing wire on extension
phone, if fitted. On DTMF lines do not
connect.
Figure
35.
Telephone Connection
Note: The microphone for recording speech
messages is on the I-SD01 module, as well as a
small speaker that allows you to playback the
messages.
If you intend to record speech messages,
and the user’s keypad is already fixed at some
distance from the central station, you may wish to
temporarily connect a second keypad to the end
station. This will enable you to program the system
and easily record/playback any speech messages.
Alternatively, you can enable the end station tamper
switch to act as a start/stop/playback recording
button.
Removing an I-SD01
If you wish to remove an I-SD01 from a system then
make sure that you first disable calls in both the
Commuations – Alarms – Call mode menu and in the
Communications – Speech Dialler – Call mode menu. If
you do not do this then the end station will
continually report a PSTN line fault.
Step 6. Fit and Connect
Battery
Fit a 7Ah Lead Acid battery into the battery
compartment in the bottom of the control unit, see
Figure 36.
Figure
36.
Fitting the Battery
Make sure that you secure the battery to the case
with the strap provided. Connect the battery leads,
red to the positive, black to the negative terminals of
the battery.
Note: Connecting the battery without mains power
will not start the system. (See “Programming A
Control Unit Before Installation” below if you wish to
start the system on battery power.)
Programming a Control Unit Before Installation
If you prefer, you can make the control unit learn
the detectors and other peripherals before installing
the system in its final location. You will need to
temporarily connect a keypad to the end station.
It is possible to temporarily operate the end station
from battery power (or a 12Vdc supply) in order to
program the system without connecting the control
unit to a mains supply. However, in order to start
the control unit processor running you must briefly
short the Kick Start pins together after connecting
the battery.
Step 7. Initial Power-Up
WARNING: During initial power-up all the keypad
sounders and any internal loudspeaker will give an
alarm tone. If you are working at the top of a ladder
make sure that the sudden noise does not startle
you and cause a fall.
1. Apply battery then mains power to the control
unit.
The keypads and internal sounder may give
an alarm tone. The heartbeat LED (see Fig 3)
starts flashing.
Note: If you are fitting an UK version of the i-on16
please go to step 6.
The display initially shows:
ABCEA1B1
SeeNote
PSTN
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Eaton i-on16 Installation guide

Eaton
Brand
Eaton
Model
i-on16
Category
Serial switch boxes
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents