Miele 52718963USA Installation Guide with Washer

Brand: Miele

Model: 52718963USA

Type: Installation Guide with Washer

Installation plan

Washer-dryer stack

PWT 6089 EL (Electrically Heated)

en - US

13.15 M.-Nr. 10 167 290 / 00

U.S.A.

Miele, Inc.

National Headquarters 9

Independence Way

Princeton, NJ 08540

Phone:

Fax:

www.mieleusa.com

Technical Service & Support

Nationwide

Phone:

800-991-9380

Fax:

800-220-1348

[email protected]

800-991-9380

609-419-9898

609-419-4241

11 3/4"

27 1/4"

76"

27 1/2"

14 5/8"

15 1/8"

52 5/8"

17 3/8"

43 1/4"

76"

30"

28 5/8"

27 1/4" 20 7/8"

50 3/4"

19 1/2"

12 3/4"

21 1/4"

30"

27 1/4"

43 1/4"

27 1/4"

27 1/2"

PWT 6089 EL - measurements in inches

51 1/8"

42 1/4"

< 39 3/8"

51 1/8"

5 7/8"

51 1/8"

< 39 3/8"

42 1/4"

43 1/4"

PWT 6089 EL - measurements in inches

76"

3/4"

27 1/4"

28"

14"

24 3/4"

17 3/8"

22"

43 1/4"

27 1/8"

1 5/8"

1/4"

PWT 6089 EL - measurements in inches

PWT 6089 EL - measurements in millimeters

Technical datasheet

Washer/Dryer stack:

Heating:

PWT 6089 LP (Drain pump)

Electric (EL)

Legend:

Abbreviations in bold type:

Connection required

en - US

Abbreviations in circle with dashes:

Connection optional or required depending on model version

Options/accessoires:

Dispensing

pump

External dispensing pumps (2 or 4 head pump):

Voltage (external power supply required)

120V

Fusing

15A

Supplied with supply cable and plug

mp installation may only be performed by Miele Service.

NEMA 5-15

Machine connections:

Electrical

connection

Standard voltage (2 AC 208V/220-240V 60Hz)

NOTE: Electrical connection depending on version ordered.

Washer (EL1) – 2 AC 208V/220-240V 60Hz

Voltage

2 AC 208 / 220-240

Frequency

Rated load

4 / 4.4 - 5.2

Fuse rating

2 x 30

Length of supply lead

78“

2000 mm

Supply lead with plug

NEMA L6-30P

Dryer (EL2) – 2AC 208V 60Hz

Voltage

2 AC 208

Frequency

Rated load

4.84

Fuse rating

2 x 30

Length of supply lead

78“

2000 mm

Supply lead with plug

NEMA L6-30P

Dryer (EL2) – 2AC 220-240V 60Hz

Voltage

2 AC 220-240

Frequency

Rated load

5.7

Fuse rating

2 x 30

Length of supply lead

78“

2000 mm

Supply lead with plug

NEMA L6-30P

Electrical connection must be in full compliance with

national regulations and

guidelines and with relevant local codes. Similarly, relevant regulations issued

by power utilities, occupational safety authorities and insurance companies as

well as good installation practices should be observed throughout.

Connection to the electrical

supply should only be performed by qualified and

properly trained persons.

Connection using a multi-pole wall lockable socket(s)

in compliance with

IEC/EN 60309 and IEC/EN 60947 is recommended in order to simplify electrical

tests. If machines are hard-wired, a multi-pole main switch must be provided on

site. Switches with a contact gap of more than 3 mm can be used. These

include

switches, fuses and contactors (IEC/EN 60947). A wall socket or

electrical isolator must be easily accessible after installation.

Reinstallation of the supply point, changes to the equipment or checks on the

protective conductor, including determination of correct fuse rating, should only

be performed by a properly trained electrician.

If necessary, equipotential bonding must be provided in accordance with all

appropriate national and local regulations.

Technical datasheet: PWT 6089 EL

Date: Feb-2015

Page: 9

Electrical

isolator

Both washer-dryer stack connections must be disengaged by a common electrical disconnect device

that switches off all poles in accordance with IEC 60947-1 [Q1].

The electrical isolator [Q1] and plug connections [EL1, EL2] must be located in the immediate vicinity

of the machine. Both must be visible, accessible and within easy reach.

If the electrical isolator [Q1] is not in full view of a person performing maintenance work on the machine

at all times, the electrical isolator must be fitted with a lock.

Installation proposals:

Technical datasheet: PWT 6089 EL

Date: Feb-2015

Page: 10

-Electrical isolator before fusing-

-Electrical isolator behind fusing-

Cold water

(Soft water)

Min. flow pressure

14.5 psi

100 kPa

Max. pressure

145 psi

1000 kPa

Max. throughput

2.9 gal/min

11 l/min

On-site connection thread

¾" external thread

Length of connection hose

(supplied: 1 connection hose)

61“

1550 mm

Hourly water demand (average for 60°C program) for

standard connection (with hot and cold water)

approx. 18.5 gal/h

approx. 70 l/h

If hot water supply is not available add hot water demand to

cold water demand.

Warm

water

(Soft water)

Max. temperature

158°F

70°C

Min. flow pressure

14.5 psi

100 kPa

Max. pressure

145 psi

1000 kPa

Max. throughput

2.9 gal/min

11 l/min

On-site connection thread

¾" external thread

Length of connection hose

(supplied: 1 connection hose)

61“

1550 mm

Hourly water demand (average for 140°F / 60°C program)

approx. 18.5 gal/hr

approx. 70 l/h

Machine can be connected to a hot water supply line with a

temperature of 158°F (70°C) to max.185°F (85°C). This

requires a separate inlet hose. This additional inlet hose is

available from Miele. The machine must also be

reprogrammed by Miele Service.

If hot water is not available, connect hot water hose to cold

water valve!

Drain

pump

Max. temperature

158°F

70°C

Drain hose(int. diameter)

7/8“

22 [DN 22] mm

On-site hose connector for drain hose

(int. diameter x length)

7/8“ x 1 3/16“

22 × 30 mm

Max. transient throughput

6.9 l/min

26 l/min

Drain pump head height (from floor level)

39 3/8“

1000 mm

Vented drainage required. If ventilation is insufficient, Miele

installation kit, Mat. no. 05238090. Drain manifolds serving

several machines must be of sufficient cross-section.

Vented

Nominal air throughput in vented mode

188 cfm

320 m³/h

Max. permissible pressure loss

0.06 psi

420 Pa

Waste air/gas temperature, max.

176°F

80°C

Connector on machine (int. diameter)

4”

100 mm

Connection pipe provided on site (ext. diameter)

4”

100 mm

Miele adapter, Mat. no. 6595070 (int. diameter 100 mm) for

flexible aluminum ducting and adapter, Mat. no. 915051,

(ext. diameter 110 mm) for connection to standard heat-

resistant plastic pipes supplied.

As relative humidity inside the vent ducting can be as high

as 100%, suitable measures must be taken to prevent a

backflow of condensate into the machine.

Air intake

Standard connection:

=> Air intake from installation site

Min. air intake cross-section

(to prevent draughts in room)

37 in

237 cm²

A sufficient supply of fresh air should be ensured to replace

the air extracted.

Fittings

(supplied)

4 × clamps

4 × screws DIN 571 (Ø × length)

1/4“ x 2“

6 × 50 mm

4 × rawl plugs (Ø × length)

5/16“ x 1 9/16“

8 × 40 mm

Machine must be bolted to the floor!

Fixing materials for a floating screed floor are to be provided

on site.

Technical datasheet: PWT 6089 EL

Date: Feb-2015

Page: 11

Machine

data

Unit width

27 1/2“

700 mm

Unit depth

30“

752 mm

Unit height

76“

1930 mm

Casing width

27 1/4“

692 mm

Casing depth

27 1/4“

690 mm

Minimum width of delivery access to installation site

28 3/8“

720 mm

Recommended rear wall gap

43 5/16“

1100 mm

Minimum rear wall gap

Recommended rear wall gap ensures sufficient space for

maintenance and servicing

35 7/16“

900 mm

Net weight

463 lbs

210 kg

Dynamic floor load, max.

3600 N

Static floor load, max.

2850 N

Dynamic load, max.

750 N

Drum frequency, max.

22 Hz

Average heat dissipation

(dependent on ambient room temperature and program

selected)

2830 BTU/hr

0.83 kWh

Sound pressure (re 20 mPA), workplace-related

(at distance of 3’ 3” / 1 m and height of 5’3” / 1.6 m)

<70dB(A)

Installation should only be carried out by authorized installers in accordance with valid regulations!

Technical datasheet: PWT 6089 EL

Date: Feb-2015

Page: 12

Miele 52718963USA Installation Guide with Washer

Miele 52718963USA Installation Guide with Washer

Miele 52718963USA Installation Guide with Washer

Related papers

Other documents