CHV-TSTATRF
infiNET™ Thermostat System
quickstart guide
www.crestron.com
888.273.7876
©2008 Specifications subject to
change without notice
201.767.3400
For details, check the latest revision of the
CHV-TSTATRF Operations & Installation Guide, Doc. 6490.
QUICKSTART DOC. 6491A (2015100) 11.08
1
CHV-TSTATRF
Heat-Only Application
Transformer
Heat
Relay
Optional, for power
R
C
System
120 VAC
Cool-Only Application
Mount the thermostat directly to
drywall or to a single-gang box in
accordance with accepted building
codes and practices. If using the
single-gang box, be sure to fill it with
thermal insulation material.
For additional details and installation
options, refer to the latest version of
the Crestron CHV-TSTATRF Operations
& Installation Guide, Doc. 6490.
Mounting
d
1
2
Connections
Connect the thermostat using the five most typical wiring configurations shown below as a guide.
For more information, refer to the Operations & Installation Guide, Doc. 6490.
Heat Pump Application With
Integrated Controller
Heat - Cool Application With
Integrated Control Unit
Dual-Fuel Heat Pump Application
Optional, for power
Transformer
R
C
C
Y
G
O
E - U - W
R
Compressor
Relay
Fan
Relay
Changeover
Valve
Aux Heat
Relay
Transformer
R
C
C
Y
G
O
R
Compressor
Relay
Fan
Relay
Changeover
Valve
Transformer
R
C
Optional, for power
Fossil Heat
System
Optional, for power
Transformer
R
C
C
Y
G
R
Compressor
Relay
Fan
Relay
Jumper from RC to RH
required only if optional
power is connected
.
Transformer
C
W
Y
G
R
Optional, for power
RH and RC mu st be
jumpered together.
Heat
Relay
Fan
Relay
Cool
Relay
R
C
RH and RC must be
jumpered together.
F F
AUTO O
H H
OFF
F F
AUTO O
H H
OFF
F F
AUTO O
H H
OFF
F F
AUTO O
H H
OFF
F F
AUTO O
H H
OFF
(Refer to Step 3)
(Refer to Step 3)
(Refer to Step 3)
(Refer to Step 3)
(Refer to Step 3)
CHV-TSTATRF
infiNET™ Thermostat System
quickstart guide
www.crestron.com
888.273.7876
©2008 Specifications subject to
change without notice
201.767.3400
For details, check the latest revision of the
CHV-TSTATRF Operations & Installation Guide, Doc. 6490.
QUICKSTART DOC. 6491A (2015100) 11.08
2
CHV-TSTATRF
3
To enter Setup mode
2
, press and hold FAN, then simultaneously press and hold k
and j for about five seconds. The display shows the Temperature Scale function
(FC).
Basic Thermostat Setup
5
System Modes and Fan Operation
4
In Setup mode, press MODE until the infiNET ID (MNET ID)
function is displayed (id). Use k and j to choose the infiNET
ID. Press MODE to select the infiNET RF Channel (CH). Note
that the function displays shown here are not consecutive.
Basic infiNET™ Setup
Use k or j to choose the temperature units: F (Fahrenheit),
C1 (Celcius, whole degree set points), or C2 (Celcius, half
degree set points). Then press MODE twice until the
Heat/Cool function is displayed (HC).
Use k and j to choose between Heat/Cool (HC), S (HP), and
Dual-Fuel Heat Pump (dF) functions. Then press MODE repeat-
edly until the Power Source function is displayed (Po).
Use k and j to choose between 24V always available
(24) and ”steal power” (SP) modes.
Use k and j to choose 11 - 26 for fixed-channel operation,
(AU) for auto channel, or (0) to disable the radio. Press MODE
until the Start infiNET Acquire function is displayed (AC).
F
AUTO
H
C
F
HOLDAUTO
H
C
F
A
OFF
FAN IN AUTO MODE
SYSTEM OFF
HOLD MODE
AMBIENT
TEMPERATURE
SET
POINT
HEAT MODE
COOL MODE
ALWAYS
DISPLAYED
AUX HEAT CALL
FAN CALL
COOL CALL
HEAT CALL
FAHRENHEIT
CELSIUS
Press the MODE button to cycle the unit
through available modes: Off, Heat,
Emergency Heat (for heat pump and dual-fuel
systems), Cool, and Auto.
2, 3
• Mode changes take place upon release of
the MODE button.
• The selected mode becomes operational
three seconds after the mode has been
entered.
Press the FAN button to toggle between Fan
Auto and Fan Always On modes.
• The fan icon is always displayed. (It may
blink to indicate an infiNET communication
problem. )
2
• When set to Fan Auto, the fan operates only
when there is a cool or heat call.
2, 4
• In system Off mode, the fan will still run if
set to Fan Always On mode.
Press MODE and FAN simultaneously to enter
Hold mode. Hold mode ignores scheduled set
point values from the control system.
Use the k and j buttons to choose the
desired temperature set point.
Thermostat Display Key
Typical Heat
Mode Display
AUTO
OFF
F
AUTO
C
F
Typical Cool
Mode Display
Typical Off
Mode Display
Press Acquire on the gateway: the Acquire LED should light.
Press k or j to start the acquire process: display shows
flashing
- - (in progress). When finished, display shows 00
(finished, found gateway) or E# (finished, could not find
gateway), where # represents an error code.
Install two AA batteries in the battery compartment.
1
After the process is complete, press Acquire on the gateway
again to exit the Acquire mode. Press FAN on the thermostat to
exit Setup mode.
F
AUTO
A
Typical
Emergency Heat
Mode Display
1. Expected battery life is 1 year using quality alkaline batteries.
2. Refer to the Operations & Installation Guide, Doc. 6490, for detailed information on setup and operating modes.
3. Thermostat firmware v1.005.0005 or later required for Auto Mode support. Auto Mode must be enabled via Setup Mode.
4. Fan will only run during heat calls if the thermostat has been configured to do so.
Flashing
F
AUTO
A
Typical
Auto Heat/Cool
Mode Display
/
