LAMONA Easton XL Single Bowl Inset/Undermount Stainless Steel Kitchen Sink Operating instructions

Brand: LAMONA

Model: Easton XL Single Bowl Inset/Undermount Stainless Steel Kitchen Sink

Type: Operating instructions

This manual is also suitable for

SNK4961

LAMONA Easton XL Single Bowl Inset/Undermount Stainless Steel Kitchen Sink is a versatile and durable addition to any kitchen. Made from high-quality stainless steel, this sink is resistant to rust and corrosion, ensuring years of reliable use. Its single bowl design provides ample space for washing dishes, cookware, and other kitchen items. The sink can be installed as either an inset or undermount, allowing you to customize it to your kitchen's design.

LAMONA Easton XL Single Bowl Inset/Undermount Stainless Steel Kitchen Sink is a versatile and durable addition to any kitchen. Made from high-quality stainless steel, this sink is resistant to rust and corrosion, ensuring years of reliable use. Its single bowl design provides ample space for washing dishes, cookware, and other kitchen items. The sink can be installed as either an inset or undermount, allowing you to customize it to your kitchen's design.

Single Bowl Inset/Undermount Sink

SNK4960

HD027060

Care and Maintenance

Do not use abrasive cleaning

products as these may scratch the

surface of the sink

Care & Maintenance

- Paint

- Chemicals

- Hot Fat

Installation

Measure and Cut

Fitting - Undermount

Fitting - Inset

1

2

3

4

7

5

6

Use the template to mark for sink cut out.

Note: Recommended distance from the back of the worktop for an inset application

is 105mm to the edge of cut out.

Apply a continuous

bead of silicone around

the rim of the sink.

Wipe around the sink rim and worktop

removing any dust or grease.

Apply a continuous bead of silicone around

the rim of the cut out where the sink will sit.

Fit the sink to the

worktop and tighten

the sink clips (x8)

on the underside to

secure.

Note: Do not use

power tools to tighten

screws.

Fit the sink to the underside of the worktop making sure

the bowl is concentric to the cut out. Push down rmly to

adhere silicone seal.

Note: Silicone the thread of the screws for extra strength.

Wipe away any excess silicone

Drill eight holes around the pencil

line and t the metal inserts,

tapping rmly into place.

NOTE: Glue the insets into the holes

and make sure the inserts do not go

over the pencil line.

WARNING: SHARP EDGES

Drill four holes, one in each corner of the

marked area. Use a jigsaw to cut-out.

The worktop will require notching on the

underside for the overow in an inset sink

application.

For undermount sink installation a jig

must be used with a router. The router will

achieve a smooth nish to the worktop

cut-out. Sand to a nal nish.

Note: Worktop cut edge should be sealed

with a waterproof varnish.

With the worktop upside down, lay the

bowl over the cut out and mark around the

edge.

Note: Make sure the bowl is concentric

with the cut out.

Inset

Undermount (Timber top application)

Template

5mm

40mm

Top surface of Worktop

5mm

2mm

6mm

Worktop

Underside

Worktop

Underside

Sink

Pe

ncil Line

Glue

x8

Wipe around the sink rim

and worktop removing

any dust or grease.

Sink Rim

x8

Silicone

Sealant

1
2

LAMONA Easton XL Single Bowl Inset/Undermount Stainless Steel Kitchen Sink Operating instructions

Brand: LAMONA

Model: Easton XL Single Bowl Inset/Undermount Stainless Steel Kitchen Sink

Type: Operating instructions

This manual is also suitable for

SNK4961

LAMONA Easton XL Single Bowl Inset/Undermount Stainless Steel Kitchen Sink is a versatile and durable addition to any kitchen. Made from high-quality stainless steel, this sink is resistant to rust and corrosion, ensuring years of reliable use. Its single bowl design provides ample space for washing dishes, cookware, and other kitchen items. The sink can be installed as either an inset or undermount, allowing you to customize it to your kitchen's design.

Download PDF

Related papers

Other documents