Furuno NAVPILOT 711C-S User manual

AUTO PILOT

NAVpilot-711C

OPERATOR'S MANUAL

www.furuno.com

Model

FURUNO Authorized Distributor/Dealer

Printed in Japan

(Elemental Chlorine Free)

The paper used in this manual

is

elemental chlorine free.

9-52, Ashihara-cho,

Nishinomiya, 662-8580, JAPAN

Pub. No. OME-72780-H4

(REFU) NAVpilot-711C

A: OCT. 2013

H4: APR 2, 2020

00017829017

i

IMPORTANT NOTICES

General

• This manual has been authored with simplified grammar, to meet the needs of international users.

• The operator of this equipment must read and follow the instructions in this manual.

Wrong operation or maintenance can void the warranty or cause injury.

• Do not copy any part of this manual without written permission from FURUNO.

• If this manual is lost or worn, contact your dealer about replacement.

• The contents of this manual and the equipment specifications can change without notice.

• The example screens (or illustrations) shown in this manual can be different from the screens you

see on your display. The screens you see depend on your system configuration and equipment

settings.

• Save this manual for future reference.

• Any modification of the equipment (including software) by persons not authorized by FURUNO will

void the warranty.

• The following concern acts as our importer in Europe, as defined in DECISION No 768/2008/EC.

- Name: FURUNO EUROPE B.V.

- Address: Ridderhaven 19B, 2984 BT Ridderkerk, The Netherlands

• All brand, product names, trademarks, registered trademarks, and service marks belong to their

respective holders.

How to discard this product

Discard this product according to local regulations for the disposal of industrial waste. For disposal in

the USA, see the homepage of the Electronics Industries Alliance (http://www.eiae.org/) for the

correct method of disposal.

How to discard a used battery

Some FURUNO products have a battery(ies). To see if your product has a battery, see the chapter

on Maintenance. If a battery is used, tape the + and - terminals of the battery before disposal to pre-

vent fire, heat generation caused by short circuit.

In the European Union

The crossed-out trash can symbol indicates that all types of batteries

must not be discarded in standard trash, or at a trash site. Take the

used batteries to a battery collection site according to your national

legislation and the Batteries Directive 2006/66/EU.

In the USA

The Mobius loop symbol (three chasing arrows) indicates that

Ni-Cd and lead-acid rechargeable batteries must be recycled.

Take the used batteries to a battery collection site according to

local laws.

In the other countries

There are no international standards for the battery recycle symbol. The number of symbols can in-

crease when the other countries make their own recycle symbols in the future.

Cd

Ni-Cd Pb

ii

SAFETY INSTRUCTIONS

WARNING

Indicates a condition that can cause death or serious injury if

not avoided.

CAUTION

Indicates a condition that can cause minor or moderate injury

if not avoided.

Warning, Caution

Mandatory Action

Prohibitive Action

Please read these safety instructions before you operate the equipment.

WARNING

Turn off the power at the switchboard

before beginning the installation.

Fire or electrical shock can result if the

power is left on.

Do not set the course changing

speed too high.

The boat will be turned too sharply at

the course change, which could create

a very dangerous situation.

Do not use the autopilot in the

following situations:

- Harbor entrance or narrow channel

- Where vessels change course often,

such as a cape or small island

Do not use the simulation mode on

the boat.

The rudder may move suddenly. This is

a special-purpose mode for technicians.

Do not use the ORBIT mode in rough

seas.

Because the boat turns a 360° circle

around the waypoint, a large wave or

strong wind can cause the boat to

capsize.

Observe the following cautions when

using the autopilot:

- Maintain a vigilant watch

- Watch for drifting of vessel

In an emergency, manually steer the

vessel.

The autopilot cannot avoid vessels, etc.

automatically.

Use the correct fuse.

Use of a wrong fuse can cause fire or

damage the equipment.

For the figure-eight mode, confirm that

no object is in the general vicinity

of the waypoint.

The distance from the waypoint to the

turning point depends on boat's speed.

Use the proper power cable.

Use JIS type DPY-2.5 or the equivalent.

Other types can cause fire.

When connecting a geomagnetic

heading sensor, correct magnetic field

deviation.

If an autopilot is used without the

compensation, unexpected course change

may occur.

Confirm that no one is near the rudder

when bleeding air from oil cylinder.

The rudder may move unexpectedly,

possibly causing bodily injury.

Set [Remote Controller 1/2] on the

[RC Setup] menu properly according to

remote controller connected.

If not done properly, malfunction may

occur. Especially, take care when

setting the NFU-type remote controller.

Do not open the equipment unless

you are well familiar with electrical

circuits.

Only qualified personnel should work

inside the equipment.

SAFETY INSTRUCTIONS

iii

WARNING

To avoid electrical shock, do not

remove cover. No user-serviceable

parts inside.

CAUTION

Confirm that the power supply voltage

is compatible with the voltage rating

of the equipment.

Connection to the wrong power supply

can cause fire or damage the equipment.

Observe the following compass safe

distances to prevent interference to a

magnetic compass:

Separate the reversible pump at least one

meter from communications equipment,

communications antenna and communi-

cations cabling to prevent interference.

In case of power failure, turn off the

autopilot or manually steer the vessel.

Leaving the equipment in the AUTO or

NAV mode during power failure will

cause wear on the rudder mechanism

About the TCT LCD

The TFT LCD is constructed using the

latest LCD techniques, and displays

99.99% of its pixels. The remaining 0.01%

of the pixels may drop out or blink, however

this is not an indication of malfunction.

Standard Steering

compass compass

0.50 m

0.35 m

0.45 m

0.30 m

0.35 m

0.30 m

Remote Controllers

(Option)

Processor Unit

FAP-7002

Control

Unit

FAP-7011C

FAP-7001

(

Option

)

WARNING LABEL

A warning label is attached to the processor unit.

Do not remove the label. If the label is missing or

damaged, contact your dealer about replacement.

Name: Warning Label (1)

Type: 86-003-1011

Code No.: 100-236-231

CAUTIONCAUTION

Keep the following points in mind

when using Fantum Feedback

TM

.

The autopilot cannot detect the rudder

position when using Fantum

Feedback

TM

. Therefore, over-steering

after reaching rudder limit can occur. If

over-steering continues, the drive unit

may malfunction, preventing automatic

steering. To prevent over-steering, keep

the following points in mind.

- Use the autopilot within the speed at

which the autopilot can control the

vessel. Pay particular attention when

keeping the stern facing windward (or

into the current) in the SABIKI mode.

- Always check the rudder position to

stop the rudder with the autopilot before

reaching the rudder limit.

- When the rudder reaches rudder limit,

the drive unit is temporarily disabled and

the autopilot cannot move the rudder. If

this occurs, the deviation alarm (see

section 3.5) sounds regardless of the

setting value. In this case, switch to the

STBY mode and turn the helm to move

the rudder.

Do not apply excessive force or shock

to the LCD.

The unit may be damaged.

WARNINGWARNING

Install an control unit (or emergency

stop button) at each helm station, to

allow you to disable the autopilot in

an emergency.

If the autopilot cannot be disabled,

accidents may result.

To disable the autopilot by operating the

emergency stop button, set [In Port1] or

[In Port2] to [Go STBY] on the

[Universal Port] menu (see section 7.8).

Do not use high-pressure cleaners to

clean this equipment.

This equipment has the waterproof

rating outlined in the specifications, at

the back of this manual. However, the

use of high-pressure cleaning equipment

can cause water ingress, resulting in

damage to, or failure of, the equipment.

iv

TABLE OF CONTENTS

FOREWORD .................................................................................................................viii

SYSTEM CONFIGURATION ..........................................................................................ix

EQUIPMENT LISTS.........................................................................................................x

1. OPERATIONAL OVERVIEW .................................................................................1-1

1.1 Controls...................................................................................................................... 1-1

1.2 How to Turn the Power On/Off................................................................................... 1-2

1.2.1 How to power the system............................................................................... 1-2

1.2.2 How to power off the system.......................................................................... 1-2

1.3 How to Adjust the Brilliance .......................................................................................1-3

1.4 How to Set the Display Color ..................................................................................... 1-3

1.5 How to Select a Display ............................................................................................. 1-4

1.5.1 Graphic displays............................................................................................. 1-4

1.5.2 Numerical display........................................................................................... 1-7

1.5.3 How to select the display data ....................................................................... 1-8

1.5.4 How to select the display data with the key operation (STBY mode only)... 1-10

2. STEERING MODES ...............................................................................................2-1

2.1 STBY Mode................................................................................................................ 2-1

2.2 AUTO Mode ............................................................................................................... 2-1

2.2.1 How to get the AUTO mode........................................................................... 2-2

2.2.2 Advanced AUTO mode .................................................................................. 2-3

2.3 NAV Mode.................................................................................................................. 2-4

2.3.1 How to get the NAV mode.............................................................................. 2-5

2.3.2 Sailing method for the NAV mode.................................................................. 2-6

2.3.3 Waypoint switching method ........................................................................... 2-7

2.3.4

How to set the steering behavior of your boat after you arrive to a waypoint

...... 2-8

2.4 Response Feature...................................................................................................... 2-9

2.4.1 How to activate the auto response feature..................................................... 2-9

2.4.2 How to activate the manual response feature................................................ 2-9

2.5 TURN Mode ............................................................................................................. 2-10

2.5.1 How to select a normal turn and start the turn ............................................. 2-10

2.5.2 Types of normal turns .................................................................................. 2-11

2.6 FishHunter

™

Mode................................................................................................... 2-13

2.6.1 How to select a FishHunter

™

turn and start the turn.................................... 2-13

2.6.2 Types of FishHunter

™

turns......................................................................... 2-16

2.6.3 How to set FishHunter

™

turn parameters .................................................... 2-20

2.7 SABIKI Mode (Outboard Vessels Only) ................................................................... 2-21

2.7.1 How to use the SABIKI mode....................................................................... 2-22

2.7.2 How to adjust the SABIKI mode response ................................................... 2-23

2.7.3 Rudder drive settings for the SABIKI mode ................................................. 2-23

2.8 How to Navigate to a TLL Position........................................................................... 2-24

2.9 DODGE Mode .......................................................................................................... 2-25

2.9.1 How to dodge in the AUTO and NAV modes............................................... 2-25

2.9.2 How to FU dodge in the STBY mode........................................................... 2-25

2.9.3 How to NFU dodge in the STBY mode ........................................................ 2-25

2.10 REMOTE Mode........................................................................................................ 2-26

2.10.1 Dial-type remote controller (FAP-5551, FAP-5552) ..................................... 2-26

2.10.2 Button-type remote controller (FAP-6211, FAP-6212),

Lever-type remote controller (FAP-6221, FAP-6222) .................................. 2-27

2.10.3 Dodge-type remote controller (FAP-6231, FAP-6232)................................. 2-28

TABLE OF CONTENTS

v

2.11 WIND Mode (for sailboats) .......................................................................................2-29

2.11.1 How to get the WIND mode..........................................................................2-29

2.11.2 Wind angle mode .........................................................................................2-30

2.11.3 TACK mode..................................................................................................2-31

2.11.4 Tacking in WIND mode (WIND TACK).........................................................2-33

2.11.5 How to reverse a heading change using the keys/knob...............................2-36

2.12 OVRD mode (for EVC system).................................................................................2-37

2.13 Safe Helm Mode.......................................................................................................2-38

2.14 Power Assist Mode...................................................................................................2-40

3. ALARMS ................................................................................................................3-1

3.1 Alarm Menu ................................................................................................................3-1

3.2 Alarm Buzzer ..............................................................................................................3-2

3.3 Buzzer Interval............................................................................................................3-2

3.4 Watch Alarm ...............................................................................................................3-3

3.5 Deviation Alarm ..........................................................................................................3-3

3.6 XTE Alarm ..................................................................................................................3-4

3.7 Arrival Alarm...............................................................................................................3-4

3.8 Speed Alarm...............................................................................................................3-5

3.9 Depth Alarm................................................................................................................3-5

3.10 Water Temperature Alarm..........................................................................................3-6

3.11 Trip Distance Alarm, Trip Distance Reset ..................................................................3-7

3.11.1 How to set the trip log alarm...........................................................................3-7

3.11.2 How to reset the trip distance.........................................................................3-7

3.12 Wind Alarms (for sailboats) ........................................................................................3-8

3.12.1 Heading change alarm ...................................................................................3-8

3.12.2 Wind deviation alarm......................................................................................3-9

3.12.3 True and apparent wind speed alarm.............................................................3-9

3.13 Alarm Log .................................................................................................................3-10

4. USER MENU..........................................................................................................4-1

4.1 Parameter Setup ........................................................................................................4-1

4.1.1 Sea state ........................................................................................................4-1

4.1.2 Trim gain ........................................................................................................4-4

4.1.3 Speed calculation ...........................................................................................4-5

4.2 Rudder Drive Level (For Fantum Feedback

™

) ...........................................................4-5

4.3 Net Towing .................................................................................................................4-6

4.4 Course After Operation of a Remote Controller .........................................................4-7

4.5 Nav Data Source ........................................................................................................4-8

4.6 NavNet vx2 Synchronization ......................................................................................4-9

4.7 Data Source Setup .....................................................................................................4-9

4.7.1 Sensor sync....................................................................................................4-9

4.7.2 Data source selection.....................................................................................4-9

4.8 System Setup Menu .................................................................................................4-10

4.9 Menu Shortcuts ........................................................................................................4-12

4.9.1 How to create a menu shortcut ....................................................................4-12

4.9.2 How to delete a menu shortcut.....................................................................4-12

5. MAINTENANCE, TROUBLESHOOTING ..............................................................5-1

5.1 Preventive Maintenance.............................................................................................5-1

5.2 Replacement of Fuse .................................................................................................5-2

5.3 Diagnostics.................................................................................................................5-2

5.3.1 Diagnostic menu.............................................................................................5-2

5.3.2 Processor unit test..........................................................................................5-3

5.3.3 Control unit test ..............................................................................................5-4

5.3.4 EVC interface test ..........................................................................................5-4

TABLE OF CONTENTS

vi

5.3.5 NMEA0183 test.............................................................................................. 5-5

5.3.6 CAN bus test.................................................................................................. 5-5

5.3.7 Key test .......................................................................................................... 5-6

5.3.8 Screen test..................................................................................................... 5-6

5.3.9 Rudder test..................................................................................................... 5-7

5.3.10 Helm sensor test .......................................................................................... 5-11

5.4 System Data............................................................................................................. 5-12

5.5 Messages................................................................................................................. 5-12

5.5.1 Message pop-up display .............................................................................. 5-12

5.5.2 Message board ............................................................................................ 5-13

5.5.3 Message description .................................................................................... 5-13

5.6 Sensor in Use Display.............................................................................................. 5-15

6. INSTALLATION AND WIRING ..............................................................................6-1

6.1 Installation .................................................................................................................. 6-1

6.1.1 Installation location......................................................................................... 6-1

6.1.2 When FAP-7011 is replaced with FAP-7011C............................................... 6-2

6.1.3 How to install the control unit ......................................................................... 6-3

6.2 Wiring ......................................................................................................................... 6-5

6.2.1 Wiring notices................................................................................................. 6-6

6.2.2 Connection with the processor unit ................................................................ 6-7

7. INITIAL SETTINGS ................................................................................................7-1

7.1 How to Select Language and Units, Open the Installation Menu Window ................. 7-1

7.2 Display Setup ............................................................................................................. 7-3

7.3 Ship’s Characteristics Menu....................................................................................... 7-4

7.4 Dockside Setup Menu ................................................................................................ 7-5

7.4.1 Dockside setup for the rudder reference unit ................................................. 7-5

7.4.2 Dockside setup for Fantum Feedback

™

...................................................... 7-11

7.4.3 How to set the safe helm mode and power assist mode.............................. 7-15

7.4.4 Confirmation of the dockside setup.............................................................. 7-19

7.5 CAN bus Port Setup................................................................................................. 7-23

7.6 NMEA0183 Port Setup............................................................................................. 7-25

7.7 Data Source Setup................................................................................................... 7-27

7.8 Universal Port Setup ................................................................................................ 7-28

7.8.1 GENERAL IN port setup .............................................................................. 7-28

7.8.2 GENERAL OUT port setup .......................................................................... 7-29

7.9 Sea Trial...................................................................................................................7-30

7.9.1 How to calibrate the compass (PG-500/PG-700)......................................... 7-31

7.9.2 How to set the rudder deadband.................................................................. 7-33

7.10 Data Calibration ....................................................................................................... 7-34

7.11 Parameter Setup Menu ............................................................................................ 7-35

7.11.1 Sea state...................................................................................................... 7-35

7.11.2 Trim gain ...................................................................................................... 7-38

7.11.3 Speed calculation......................................................................................... 7-39

7.12 AUTO Option Menu.................................................................................................. 7-39

7.13 NAV Option Menu .................................................................................................... 7-40

7.13.1 How to select the source for nav data.......................................................... 7-41

7.14 Fish Hunter Option Menu......................................................................................... 7-42

7.15 Wind Option Menu ................................................................................................... 7-43

7.16 System Setup Menu................................................................................................. 7-44

7.17 RC (Remote Controller) Setup Menu ....................................................................... 7-45

7.18 All Clear (Default Setting)......................................................................................... 7-45

TABLE OF CONTENTS

vii

APPENDIX 1 MENU TREE .......................................................................................AP-1

APPENDIX 2 JIS CABLE GUIDE .............................................................................AP-6

SPECIFICATIONS ..................................................................................................... SP-1

PACKING LIST............................................................................................................ A-1

OUTLINE DRAWING................................................................................................... D-1

INTERCONNECTION DIAGRAM ................................................................................ S-1

INDEX ......................................................................................................................... IN-1

viii

FOREWORD

A Word to the Owner of the NAVpilot-711C

Congratulations on your choice of the NAVpilot-711C. We are confident you will see why the

FURUNO name has become synonymous with quality and reliability.

Since 1948, FURUNO Electric Company has enjoyed an enviable reputation for innovative and

dependable marine electronics equipment. This dedication to excellence is furthered by our

extensive global network of agents and dealers.

Your equipment is designed and constructed to meet the rigorous demands of the marine

environment. However, no machine can perform its intended function unless properly operated

and maintained. Please carefully read and follow the operation and maintenance procedures set

forth in this manual.

Thank you for considering and purchasing FURUNO.

We would appreciate feedback from you, the end-user, about whether we are achieving our goal.

Features

The NAVpilot-711C can steer a power boat or sailboat whose length is between 30 and 80 ft, and

high-speed vessel (max. 40 kn).

The main features of the NAVpilot-711C are

• “Adaptive” technology allows NAVpilot to continually improve your vessel’s steering on every

voyage

• Auto set-up and self-learning for vessel speed and course

• Versatile, high-resolution color LCDs provide a variety of user-defined display configurations

• One-touch operation for STBY, NAV and AUTO modes

• “FishHunter

™

” guides your vessel in circle, orbit, spiral, figure-eight, square or zigzag maneuver

around fish or other target

• Network up to six control units

CE declaration

With regards to CE declarations, please refer to our website (www.furuno.com) for further infor-

mation about RoHS conformity declarations.

ix

SYSTEM CONFIGURATION

Control Unit

FAP-7011C

Control Unit

FAP-7001

Contact Signal IN

Contact Signal OUT

PC (for serviceman)

Heading Sensor

PG-700

External Buzzer

Event Switch

NAV Equipment

(NMEA 0183)

CAN bus Equipment

(NMEA 2000)

EVC System*

5

12-24 VDC

Solenoid

Valve

Hydraulic Linear Drive

Rudder Reference Unit

FAP-6112*

2

Ship's

Steering

System*

3

Remote Controller

Distributor FAP-6800

Remote Controller

*

1

: Attach the terminator (type: BD-07AFFM-LR7001) to the port not used on the last control unit

in the series.

*

2

: Not required for Fantum Feedback

TM

([Rudder Sensor] = [Fantum Feedback]).

*

3

: Not required for a EVC system equipped vessel.

*

4

: Connect one Dial-type Remote Controller FAP-5551 to one Distributor FAP-6800.

*

5

: EVC systems compatible with the NAVpilot are as follows:

Remote Controller:

Dial Type: FAP-5551*

4

, FAP-5552

Button Type: FAP-6211, FAP-6212

Lever Type: FAP-6221, FAP-6222

Dodge Type: FAP-6231, FAP-6232

Control Unit Qty: Max. 6*

1

The processor unit has two connection

lines for the control unit.

Three control units can be connected

per each connection line.

: Standard

: Option

: User Supply

Processor Unit

FAP-7002

EVC System Remarks

VOLVO PENTA IPS

YAMAHA Helm Master

YANMAR VC10

SEASTAR SOLUTIONS

OPTIMUS

Requires VOLVO interface kit FAP-6300 (available as an optional extra).

Requires YAMAHA HM interface kit FAP-6310 (available as an optional extra).

• Connect through the NMEA data converter IF-NMEA2K2 (ver.01.07 or later).

• Requires connector assembly AT06-2S-EC01-VCT-030 (available as an optional extra).

• Connect through the NMEA data converter IF-NMEA2K2 (ver.01.16 or later).

• The software version of the connected Main PCM (Pump Control Module) must be “Rev. T” or

later.

x

EQUIPMENT LISTS

Standard supply

Option supply

Name Type Code No. Qty Remarks

Control Unit FAP-7011C - 1

Processor Unit FAP-7002 - 1

Rudder Refer-

ence Unit

FAP-6112-200 - 1

May or may not be supplied

depending on order.

Installation

Materials

CP64-03101 001-082-720 1 For processor unit

CP64-02601 009-001-170 1

For rudder reference unit

May or may not be supplied

depending on order.

Spare Parts SP64-01501 001-082-710 1 For processor unit, fuse

Sponge TZ8103008A - 1

For control unit, installation

materials

Cable Assy. BD-07AFFM-LR-150 001-081-180-10 1

Terminator BD-07AFFM-LR-7001 001-081-140-10 1 For control unit, accessory

VOLVO Interface

Kit

FAP-6300 000-036-494

1

May or may not be supplied

depending on order.

YAMAHA HM IF

Kit

FAP-6310 000-027-160

Name Type Code No. Remarks

Control Unit

FAP-7001 - Max. 5 optional units

FAP-7011C - Max. 5 optional units

Remote Controller

FAP-5551 - Dial type, w/connector

FAP-5552 - Dial type, no connector

FAP-6211 - Button type, w/connector

FAP-6212 - Button type, no connector

FAP-6221 - Lever Type, w/connector

FAP-6222 - Lever Type, no connector

FAP-6231 - Dodge type, w/connector

FAP-6232 - Dodge type, no connector

Rudder Reference

Unit

FAP-6112-200

-

w/20 m cable

Junction

Box

FI-5002 - w/self-tapping screws

NMEA Data

Converter

IF-NMEA2K2

-

VOLVO Interface

Kit

FAP-6300 000-036-494

For the EVC system equipped

vessel

YAMAHA HM IF

Kit

FAP-6310 000-027-160

IPS Interface Unit IF-700IPS 000-022-972

VOLVO IPS

Gateway

AUTOPILOT-GATEWAY -

YAMAHA HM

Gateway

YAMAHA-HM-GATEWAY

-

EQUIPMENT LISTS

xi

Distributor FAP-6800 000-090-242

For connection of three remote

controllers

Terminator BD-07AFFM-LR7001 001-081-140-10

Cable Assy.

MJ-A10SPF0001-060+ 001-081-150-10 For distributor, 6 m

MJ-A10SPF0001-120+ 001-081-160-10 For distributor, 12 m

BD-07AFFM-LR-100 001-081-170-10

For control unit, 10 m,

connector at one end

BD-07AFFM-LR-150 001-081-180-10

For control unit, 15 m,

connector at one end

BD-07AFFM-LR-200 001-081-190-10

For control unit, 20 m,

connector at one end

BD-07AF-07AF-LR-100 001-081-200-10

For control unit, 10 m,

connector at both ends

BD-07AF-07AF-LR-200 001-081-210-10

For control unit, 20 m,

connector at both ends

M12-05BFFM-010 000-167-965-10

CAN bus drop cable, 1 m, mi-

cro

M12-05BFFM-020 000-167-966-10

CAN bus drop cable, 2 m, mi-

cro

M12-05BFFM-060 000-167-967-10

CAN bus drop cable, 6 m, mi-

cro

CB-05BFFM-010 000-167-971-10

CAN bus drop cable, 1 m, mi-

cro, mini

CB-05BFFM-020 000-167-972-10

CAN bus drop cable, 2 m, mi-

cro, mini

CB-05BFFM-060 000-167-973-10

CAN bus drop cable, 6 m, mi-

cro, mini

T-type

Connector

SS-050505-FMF-TS001 000-168-603-10 For CAN bus, micro+micro

NC-050505-FMF-TS001 000-160-507-10 For CAN bus, mini+micro

Termination

Resistor

LTWMC-05BMMT-

SL8001

000-168-604-10 For CAN bus, micro, male

LTWMN-05AMMT-

SL8001

000-160-508-10 For CAN bus, mini, male

LTWMC-05BFFT-SL8001 000-168-605-10 For CAN bus, micro, female

LTWMN-05AFFT-SL8001 000-160-509-10 For CAN bus, micro, male

Connector

Assembly

AT06-2S-EC01-VCT-030 000-193-626-10

For connection with Yanmar

VC10

Flush

Mount Kit

FAP-7001-FLUSH-KIT 001-082-730 For FAP-7001

Bracket Assembly

FAP-7001-BRACKET 001-082-750 For FAP-7001

OP64-12 001-434-490 For FAP-7011C

OP64-2 009-004-030 For FAP-5551/5552

Flush

Mount Kit

OP64-4 009-005-790

For FAP-6221/6222, panel

type

OP64-5 009-005-800

For FAP-6221/6222, surface

type

Name Type Code No. Remarks

EQUIPMENT LISTS

xii

Discontinued products

The following products are discontinued:

Name Type Date

Remote Controller

FAP-5551 December, 2017

FAP-5552 December, 2017

1-1

1. OPERATIONAL OVERVIEW

1.1 Controls

Press and hold the key, then press the AUTO key to get the WIND mode

(sailboats only).

(MENU) key

Momentary press: Open the turn menu.

Long press: Open/close the menu.

NAV key

Select the NAV mode.

AUTO key

Select the AUTO mode.

(PORT) key

Steer boat to port.

(STBD) key

Steer boat to starboard.

(POWER/STBY) key

Momentary press:

• Turn on power.

• Go to the STBY mode.

Long press: Turn off power.

Course control knob

Rotate:

• Select menu items and options.

• Set course on the AUTO mode.

Push: Confirm menu setting.

1. OPERATIONAL OVERVIEW

1-2

1.2 How to Turn the Power On/Off

Note: When the heading sensor PG-500/PG-700 is connected, turn on the NAVpilot

and wait four minutes before you leave port. This allows time for the PG-500/PG-700

heading data to stabilize.

1.2.1 How to power the system

Press the key to power the system. A beep sounds and the result of the start up

test appears followed by the start screen. The startup test checks the ROM, RAM and

backup of the processor unit and control unit. The test also checks for the presence of

heading from the heading sensor and rudder angle information from the rudder refer-

ence unit.

Note: The content of the startup test changes according to your system configuration.

If “NG” appears for any item, an error message, shown in the table below, appears.

Follow the information provided in the message to restore normal operation. If you

cannot restore normal operation, contact your dealer.

1.2.2 How to power off the system

Long press the key to power off the system. While pressing the key, the display

shows the number of seconds remaining until the power is turned off.

Error message Meaning

System has failed startup test. Please contact a lo-

cal FURUNO representative for repair if problem

re-occurs.

The system has failed the start up

test.

Back-up data is corrupt factory defaults will be re-

stored (processor). Push any key to continue.

Backup data of the processor unit

is corrupted.

Back-up data is corrupt factory defaults will be re-

stored (controller). Push any key to continue.

Backup data of the control unit is

corrupted.

Cannot receive heading data. Please check the

heading sensor.

Problem with heading sensor.

EVC Interface has failed startup test. Please con-

tact a local FURUNO representative for repair.

Push any key to continue.

System error of the IPS interface

unit or NMEA data converter. Turn

off the autopilot, contact your deal-

er.

No connect EVC Interface. Please check the EVC

Interface. Push check the heading sensor.

The IPS interface unit or NMEA

data converter is not connected.

Check the connection with IPS in-

terface unit or NMEA data convert-

er.

NAVpilot-711C Startup Test

Processor 6454007-**.**

Controller 6454011-**.**

ROM RAM Backup

Processor OK OK OK

Controller OK OK OK

Heading Sensor OK xx.x°

RRU OK P12.3°

Controller ID: 1

**.** : Program version no.

1. OPERATIONAL OVERVIEW

1-3

1.3 How to Adjust the Brilliance

1. Long press the key to open the menu.

2. Rotate the Course control knob to select [Brilliance] then push the knob.

The brilliance adjust window appears. The window closes automatically when

there is no operation for a while.

3. Rotate the Course control knob to adjust the brilliance.

The higher the value, the brighter the display.

4. Push the Course control knob to close the window.

5. Push the key to close the menu.

1.4 How to Set the Display Color

1. Long press the key to open the menu.

2. Rotate the Course control knob to select the current setting for [Display Color]

then push the knob.

3. Rotate the Course control knob to select the display color.

[White]: White-themed display

[Black]: Black-themed display

4. Push the key to close the menu.

Message

Display Color : White

Sensor In Use

Brilliance

Advanced AUTO: ON

Net Towing AUTO : OFF

Message

Display Color : White

Sensor In Use

Brilliance

Advanced AUTO: ON

Net Towing AUTO : OFF

Example: [Display Color] = [White] Example: [Display Color] = [Black]

1. OPERATIONAL OVERVIEW

1-4

1.5 How to Select a Display

There are three displays to select from each steering mode.

To select a display, do the following operation according to the steering mode.

• STBY mode: Press the key

• AUTO and WIND mode: Press the AUTO key.

• NAV mode: Press the NAV key.

Note: Page layout of the page 3 depends on setting of [Data Box Format].

1.5.1 Graphic displays

There are five types of the graphic displays: compass, highway, wind, rudder, engine

speed display.

Compass display

The compass display show ship’s heading data. The compass rotates to keep the

ship’s heading (gray pointer) at the top of the display. Requires heading data.

㪲㪉㪴

䋪

㪲㪊㪴

䋪

㪲㪈㪴

䋪

Graphic

or

Numerical display

䋪

: Page no. appears when selecting display.

Graphic

or

Numerical display

Graphic

or

Numerical display

Data box

Analog indicator

Analog

indicator

SETCSESETCSE

Ship's heading

(Gray pointer)

Set course / waypoint cource

(Red pointer)

Steering mode data

(See page 1-6.)

1. OPERATIONAL OVERVIEW

1-5

Highway display

The highway display provides a graphic presentation of your boat’s progress along its

intended course. The own ship marker moves according to your boat’s track to the

waypoint.

Wind display

The wind display shows wind angle and wind speed. The data can be shown in true

wind or apparent wind. The apparent wind is the actual flow of air acting upon a sail,

or the wind as it appears to the sailor. The true wind is the wind seen by a stationary

observer in velocity and direction. Requires a wind sensor.

Direction to next waypoint

Waypoint name

Own ship mark

HDG T

Steering mode data

(See page 1-6.)

Estimated time of arrival

(Turn to STBD)(Turn to PORT)

Waypoint mark

Ship's heading

Wind mode:

Ship's heading

Set wind angle

(Blue pointer)

Wind angle

(Red pointer)

Steering mode data

(See page 1-6.)

Wind speed

Wind angle

S

30.0°

10.2

kn

9 0

90

1 20

120

: True

: Apparent

1. OPERATIONAL OVERVIEW

1-6

Rudder display

The rudder display shows analog and digital rudder angle.

Note: Not available with Fantum Feedback

™

.

Engine speed display

The engine speed display shows the engine revolution. Requires engine speed data.

Steering mode data

The table below shows the steering mode data that appears on the graphic display.

Steering mode Display

STBY mode Ship’s heading

AUTO mode Set course

NAV mode

[NAV mode] = [Course]

Waypoint course

NAV mode

[NAV mode] = [XTE(Precision)] or [XTE(Economy)]

Cross-track error

WIND mode Set wind angle

SETCSE

HDG T

Rudder angle/direction

P: to “port”

S: to “starboard”

Rudder angle

(Analog)

Ship's heading

Steering mode data

(See page 1-6.)

Ship's heading

Engine speed

(Analog)

Steering mode data

(See page 1-6.)

Engine speed

SETCSESETCSE

HDG THDG T

Page is loading ...

Furuno NAVPILOT 711C-S User manual

This manual is also suitable for

Furuno NAVPILOT 711C-S User manual

Related papers

Other documents