Sanus SAN213 User manual

Brand: Sanus

Model: SAN213

Category: Flat panel wall mounts

Type: User manual

Sanus Systems

2221 Hwy 36 West

Saint Paul, MN 55113 USA

Customer Service

Americas: 800-359-5520 • 651-484-7988 • [email protected]

Europe, Middle East, and Africa: + 31 40 2324700 • europe.sanus@milestone.com

Asia Paciﬁ c: 86 755 8996 9226 • [email protected]om

accents.sanus.com

All other brand names or marks are used for identiﬁ cation purposes and are trademarks of their respective owners.

(6904-002011<01>)

SAN213

Wood

Solid or Block

Concrete

5.5mm

(7/32 in.)

10mm

(3/8 in.)

13mm

(1/2 in.)

6904-002011<01>2

OPT

Wood stud walls

Solid Concrete and Concrete

Block Mounting

Choose an Option Do Not

WARNING: This product

contains small items that could

be a choking hazard.

Tools required

Caution / Warning Heavy! Assistance Required. Unlock/Lock This End Up

6904-002011<01> 3

169.3 mm

6.67 in.

143.5 mm

5.65 in.

318.3 mm

12.53 in.

64.3 mm

2.53 in.

100 mm

3.94 in.

75 mm

2.95 in.

200 mm

7.87 in.

230 mm

9.06 in.

59.2 mm

2.33 in.

100 mm

3.94 in.

75 mm

2.95 in.

241 mm

9.49 in.

256.1 mm

10.08 in.

360º

180°

15°

6904-002011<01>4

IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS – PLEASE READ ENTIRE MANUAL BEFORE USING THIS PRODUCT

Speci cations

 Weight capacity-DO NOT EXCEED: 20.5 kg (45 lbs) includes TV and any accessories

CAUTION: Avoid potential personal injuries and property damage!

 Do not use this product for any purpose not explicitly speci ed by manufacturer.

 The wall must be capable of supporting  ve times the weight of the monitor and mount combined.

 This product is not designed for use in metal stud walls!

 If you do not understand these instructions, or have doubts about the safety of the installation, assembly or use of this product, contact manufacturer

Customer Service or call a quali ed contractor.

 Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.

CAUTION:

Supplied Parts and Hardware.

Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer

Service. Never use damaged parts!

NOTE:

Not all hardware included will be used.

6904-002011<01> 5

[11] x 4

[06] x 1

[01] x 1

[18] x 1

[07] x 1

[17] x 4

[03] x 2 [04] x 2 [05] x 1

[08] x 1 [09] x 1 [10] x 2

[12] x 4 [13] x 4 [14] x 2 [15] x 4 [16] x 4

1/4-20 x 3 ¼ in.5/16 x 2 ½ in.

1/4-20 in. 0.5 in. 0.5 in.

M4 x 30mm

8-32 x 0.5 in.

M4 x 12mm

[02] x 1

5/32 in.

6904-002011<01>6

1-1

1-2

For TVs with a  at/unobstructed back. Ensure that

the bracket is level on the back of the TV. Standard

con gurations are shown. If you need extra space

to accommodate cables, recesses, or protrusions,

see installation option 1-2 that uses spacers. For

special applications, or if you are uncertain about your

hardware selection, contact Customer Service.

For TVs with an irregular/obstructed back. Ensure that

the bracket is level on the back of the TV. Standard

con gurations are shown. For special applications, or

if you are uncertain about your hardware selection,

contact Customer Service.

OPT

[02]

[11]

[12]

[13]

6904-002011<01> 7

6904-002011<01>8

CAUTION:

Wall Mounting

2-1: Wood Stud Mounting

CAUTION:

Improper use could reduce the holding power of the lag bolt. To avoid potential injuries or property damage:

 Pilot holes MUST be drilled to a depth of 63.5 mm (2.5 in.), using a 5.5 mm (7/32 in.) diameter drill bit.

 DO NOT over-tighten the lag bolts [03].

 Any material covering the wall must not exceed 16 mm (5/8 in.).

 Minimum wood stud size: common 2 x 4 in. (nominal 1.5 x 3.5 in.)

2-2: Solid Concrete and Concrete Block Mounting

CAUTION:

Improper use could reduce the holding power of the lag bolt. To avoid potential injuries or property damage:

 Pilot holes MUST be drilled to a depth of 63.5 mm (2.5 in.), using a 10 mm (3/8 in.) diameter drill bit.

 Be sure the anchors [04] seat  ush with the concrete surface.

 Mount wall plate directly onto the concrete surface.

 Never drill into the mortar between blocks.

 DO NOT over-tighten the lag bolts [03].

 Minimum solid concrete thickness: 8 in.

 Minimum concrete block size: 8 x 8 x 16 in.

6904-002011<01> 9

Wood Stud Wall Mounting – See Cautions in Step 2.

1. Locate stud. Verify the center of the stud with an awl or thin nail or use

an edge to edge stud  nder.

2. Level the wall plate [01] and mark the hole locations.

3. Drill pilot holes as illustrated.

4. Place the wall plate against the wall. Tighten lag bolts [03] only until

they are pulled  rmly against the wall plate [01].

5. Place lag bolt covers [16] over lag bolts [03].

2-1

13mm

(1/2 in.)

5.5mm

(7/32 in.)

< 16 mm

(5/8 in.)

[01]

[03]

[16]

63.5 mm

2.5 in.

6904-002011<01>10

10mm

(3/8 in.)

2-2

Solid Concrete and Concrete Block Mounting – See Cautions in Step 2.

1. Level wall plate and mark the hole locations.

2. Drill pilot holes as illustrated.

3. Insert lag bolt anchors [04].

4. Place the wall plate against the wall. Tighten lag bolts [03] only until

they are pulled  rmly against the wall plate [01]..

5. Place lag bolt covers [16] over lag bolts [03].

13mm

(1/2 in.)

[01]

[16]

[03]

[04]

75 mm

3 in.

6904-002011<01> 11

1. Fit nut [08] and cover [16] into underside of mount arm [01].

2. Place washer [07] and pivot pin [06] onto mount arm.

3. Heavy: You will need assistance with this step! Fit mounting bracket

[02] onto pivot pin [06]. Slide washers [10] and spacer [09] onto

mounting bolt [05] and  t bolt through mounting bracket [02] and pivot

pin [06] until it meets nut [08].

4. Use hex key [18] to tighten mounting bolt [05] and secure mounting

bracket [02] to arm [01].

[16]

[05]

[10]

[09]

[10]

[02]

[06]

[08]

[16]

[07]

[18]

6904-002011<01>12

Arrange Cables and Add Plates

NOTE: Pull the arm to its full extension before routing the cables through

the channels, then loosely route the cables. This will give the cables enough

slack to prevent excess tension when adjusting the position of the arm.

[14]

[15]

[17]

[15]

[17]

[15]

[17]

[01]

OPT

6904-002011<01> 13

A: Adjust arm extend / retract tension

B: Adjust left / right swivel tension

C: Adjust up / down tilt tension

[18]

TOP VIEW

SIDE VIEW

6904-002011<01>14

Milestone AV Technologies and its a liated corporations and subsidiaries (collectively, “Milestone”), intend to make this manual accurate and complete. However,

Milestone makes no claim that the information contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in

connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind.

Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy,

completeness or su ciency of the information contained in this document.