IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
CONTACT OVERSTOCK.COM CUSTOMER SERVICE AT
1-800-843-2446
180106rev1
Read the instructions and precautions before use of this product
Please keep this instruction manual for future reference
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
CONTACT CONSUMER SUPPORT AT
1-800-843-2446
Warranty Information:
Products for Home Use
This item and or product is not covered under original manufacturer's warranty.
For warranty issues please contact the retailer directly at
1-800-843-2446
or
www.Overstock.com
Made in China
Distributed by:
Overstock.com
6350 South 3000 East
Salt Lake City, UT 84121
OV SKU No. 10085156-000-000
Model No. 50103303
Fallbrook Bar Stool
Instruction Manual
Due to ongoing product development
the actual product or products may vary from
the illustrations or photos shown within this manual.
NOTE: This product is intended for residential, non-commercial use.
1
2
F
G
I
F
G
H
J
K
L
M
Figure 1
Armrest
Seat
Seat Back
Footrest
Back Support
8mm Threaded Stud
8mm Flat Washer
8mm Hex Nut
8mm Cap Nut
6mm Threaded Stud
6mm Flat Washer
6mm Hex Nut
Adjustable Foot Pad
G
H
I
J
K
L
M
16
8
8
12
12
12
8
A
B
C
D
E
F
16
2
2
2
2
4
A
B
C
D
E
F
G
H
I
J
K
L
M
ASSEMBLY INSTRUCTIONS
Attach Seat Back to Left Side of Chair
1.(SEE FIGURE 1) Install four threaded studs (F) into seat back (C).
2.Place the (seat back) threaded studs through armrests (A) mounting tabs. Attach each stud
using flat washer (G) and cap nut (I). Do not over tighten.
Attach Seat to Left Side of Chair
1.Screw four threaded studs (F) into the seat (B).
2.Place the (seat) threaded studs through the armrest (A) mounting tabs. Attach each stud
using flat washer (G) and hex nut (H). Do not over tighten.
Attach Back Support Bar, Footrest
1.Attach back support bar (E) to left armrest with threaded stud (J), flat washer (K) and
hex nut (L). Do not over tighten.
2.Attach footrest (D) to left armrest (A) with two threaded studs (J), flat washers (K) and
hex nuts (L). Do not over tighten.
Attach Left and Right Sides of Chair
1.Attach back support bar (E) and footrest (D) to the right armrest (A) with three threaded
studs (J), flat washers (K), and hex nuts (L).
2.Connect the seat (B) and back (C) with four threaded studs (F), flat washers (G),
and hex nuts (H) and cap nuts (I).
3.Stand the chair upright. Tighten all bolts.
4.Screw in and adjust the footpads (M) to level the chair.
Carefully remove the contents from the package. If any parts are missing do not
attempt to use the product until they have been obtained and correctly installed.
IF YOU HAVE PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN TO YOUR RETAILER. CONTACT CUSTOMER SERVICE AT
1-800-843-2446.
PARTS & HARDWARE LIST
PART # DESCRIPTION QUANTITY
NOTE: This product is intended for residential, non-commercial use.
A
A
B
C
E
D
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Ki Mobility ROGUE XP User Instruction Manual & Warranty
-
Invacare Ranger IISTANDARD User manual
-
Invacare MyOn HC User manual
-
-
Star Trac Instinct Owner's manual
-
-
Invacare MWD User manual
-
-
-
