Astonica 50101033 User manual

Brand: Astonica

Model: 50101033

Type: User manual

OUTDOOR LIVING

Read the instructions and precautions before use of this product

MODEL NO: 50101033

Please keep this instruction manual for future reference

Made in China

World Factory, Inc.®

Southlake, TX

1-888-422-7800

Limited Warranty

World Factory, Inc.® Products for Home Use

World Factory, Inc.® (Seller) warrants to the original Buyer only, that each Astonica™ Product will be free

from defects in material and workmanship for a period of one (1) year from date of purchase. SELLER’S

SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL

BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH ARE DEFECTIVE IN

MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE SELLER WHICH HAVE BEEN

MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY FROM REPAIRS OR

ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER MAINTENANCE, NEGLECT

OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This warranty does not apply to

damage, heat-induced coloration changes, scratching or alteration due to normal use or weathering. To

make a claim under this Limited Warranty, you must return the complete product, transportation prepaid, to

any World Factory, Inc.® authorized service center. Call 1-888-422-7800 for the location of the nearest

authorized service center.

Additional Limitations

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED

TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1) YEAR

FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR

CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS,

ARISING FROM THE SALE OR USE OF THIS PRODUCT.

If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such provision

shall not affect any other provision herein, this Limited Warranty shall be construed as if such invalid and/or

unenforceable provision had never been contained herein.

This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all prior

agreements, arrangements, or understandings between the parties relating to product warranty.

IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,

DO NOT RETURN IT TO YOUR RETAILER, CONTACT CUSTOMER SERVICE AT

1-888-422-7800.

IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,

DO NOT RETURN IT TO YOUR RETAILER, CONTACT CUSTOMER SERVICE AT

1-888-422-7800.

CAST ALUMINUM LOUNGER

Instruction Manual

2 3

PARTS & HARDWARE LIST

PART # DESCRIPTION QUANTITY

1Seat

B 1Backrest

C 2Front Leg

D 2Armrest Assembly

E 2Wheel

F 1Backrest Support Bar

Axle

8mm x 40 Screw

8mm x 35 Stud

8mm x 30 Stud

6mm x 45 Screw

8mm Flat Washer

8mm Lock Washer

8mm Hex Nut

ASSEMBLY INSTRUCTIONS

IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,

DO NOT RETURN IT TO YOUR RETAILER. CONTACT CUSTOMER SERVICE AT

1-888-422-7800.

Carefully remove the contents from the package.

If any parts are missing do not attempt to use the product until they have

been obtained and correctly installed.

1. Turn the seat (A) upside down on a non-scratching surface. Attach the front

legs (C) to the seat (A) by threading (6) 8mm x 35 studs (I) into the holes under

the front end of the seat (A). Place the legs (C) over the studs (I) and secure

them in place with (6) 8mm flat washers (L), lock washers (M), and hex nuts (N).

2. Insert the axle (G) into both armrest assemblies (D). Then, align the holes in the

sides of the armrest assemblies (D) with those in the sides of the seat (A).

Secure them together with (2) 8mm x 40 screws (H) and lock washers (M) on

each side, screwing them in from the outside.

3. Slide a wheel (E) onto the axle (G). Screw in an 8mm x 30 stud (J), then place a

16mm flat washer (S), 8mm lock washer (M) and hex cap nut (O) on the end to

secure the wheel (E) in place. Repeat this procedure with the other wheel (E).

4. Attach the backrest (B) to the armrest (D) with an 8mm x 45 screw (H) and flat

washer (T) on each side, screwing them in from the outside.

5. Attach the backrest support bar (F) to the backrest (B) using a 6mm x 45 screw

(K), flat washer (P), lock washer (Q) and hex cap nut (R).

6. Adjust the inclination of the backrest (B) by placing the backrest support bar (F)

in the desired notch on the back of the armrest assembly (D).

8mm Hex Cap Nut

6mm Flat Washer

6mm Lock Washer

6mm Hex Cap Nut

16mm Flat Washer

8mm Flat Washer

Astonica 50101033 User manual

Astonica 50101033 User manual

Astonica 50101033 User manual

Related papers

Other documents