AVFI SYZ42 stand Assembly Instructions

Brand
AVFI
Model
SYZ42 stand
Type
Assembly Instructions

AVFI SYZ42 stand is designed for free-standing mounting of SMART kapp 42® and up to 60” screens weighing up to 75 lbs. It can be used in both portrait and landscape orientations, with VESA patterns of 400mm X 400mm, or 400mm X 200mm. The stand comes with a variety of hardware to ensure compatibility with most displays, and includes adhesive bumpers to protect the display from scratches. Assembly is simple and can be completed by two people in a few minutes. The stand's height can be adjusted to accommodate different viewing heights, and it features a sturdy base with wheels for easy mobility.

AVFI SYZ42 stand is designed for free-standing mounting of SMART kapp 42® and up to 60” screens weighing up to 75 lbs. It can be used in both portrait and landscape orientations, with VESA patterns of 400mm X 400mm, or 400mm X 200mm. The stand comes with a variety of hardware to ensure compatibility with most displays, and includes adhesive bumpers to protect the display from scratches. Assembly is simple and can be completed by two people in a few minutes. The stand's height can be adjusted to accommodate different viewing heights, and it features a sturdy base with wheels for easy mobility.

VF
I
Assembly Instructions
SYZ42 Stand
Thank you for purchasing AVFI’s SYZ42 Stand
This product is design for free standing mounting of SMART kapp 42® and up to 60” screen up to 75 lbs.
For portrait setup VESA pattern must be centered; 400mm X 400mm, 400mm X 200mm ONLY
Confirm all hardware is included before you begin assembly.
Read these instructions start to finish before beginning installation.
Have at least 2 people mount the display.
Note: If you cannot understand these instructions or are concerned about safety of the installation contact a qualified
contractor or contact VFI at 1-877-834-3876
Supplied Parts
Bracket
(1)
Supplied Hardware for Kapp 42
Black Spacer
(4)
M10 X 35
(4)
Adhesive Bumper
(1)
1
www.video-furn.com
190 Don Hillock Drive |Aurora |Ontario|L4G 0G9 | 1.877.834.3876
www.video-furn.com
190 Don Hillock Drive |Aurora |Ontario|L4G 0G9 | 1.877.834.3876
M6 X 25
(10)
Base with wheels
(1)
Not all hardware supplied will be used, depending on the manufacturer of your display.
Hex Key M6 (Supplied in Hardware Kit S 42-84)
Hex Key M10 (Supplied in Hardware Kit TV 52-70)
Hardware Bag
(3)
• Kit S 42-84
• Kit TV52-70
Tools required
Structural Tube
(1)
Place parts on non abrasive surface
Install grommets onto the holes of the tube
1
M6 X 25 (6)
• Kit Grommet &
Adhesive Bumper
Adhesive Bumper
(2)
Install plate onto the structure tube
Insert M6 x 25 (6) starting from the top
of the tube to position bracket onto highest
height
Grommet (2)
4
VF
I
Assembly Instructions
SYZ42 Stand
2
www.video-furn.com
190 Don Hillock Drive |Aurora |Ontario|L4G 0G9 | 1.877.834.3876
If monitor height is not the desired, adjust
where bracket mounts on the structural tube.
Assembly is complete, enjoy your stand
Place parts on non abrasive surface Install base to structure tube
From under the base hand tighten all 4 X M10
bolts onto the holes attaching the structural
base to it. Tighten securely with a wrench. For
a SMART kapp 42® installation attach the
adhesive bumper at least 32” from the base.
2
3
Lay the monitor on the floor and
turn the stand over and place it on
top of the monitor
For a SMART kapp 42® insert M6 X 25 (4)
into hole of monitor having the spacers in
between the monitor and the bracket. If
installing a monitor different than a Kapp42 a
general hardware kit is included (TV 52-70)
Use the Hex key to tighten until there is
resistance, then give a half turn. DO NOT
OVERTHIGHTEN AS THIS CAN DAMAGE OR
PUNCTURE THE MONITOR.
M10 X 35
(4)
Adhesive Bumper
(1)
M6 X 25 (4)
Black Spacer (4)
Lift the stand
  • Page 1 1
  • Page 2 2

AVFI SYZ42 stand Assembly Instructions

Brand
AVFI
Model
SYZ42 stand
Type
Assembly Instructions

AVFI SYZ42 stand is designed for free-standing mounting of SMART kapp 42® and up to 60” screens weighing up to 75 lbs. It can be used in both portrait and landscape orientations, with VESA patterns of 400mm X 400mm, or 400mm X 200mm. The stand comes with a variety of hardware to ensure compatibility with most displays, and includes adhesive bumpers to protect the display from scratches. Assembly is simple and can be completed by two people in a few minutes. The stand's height can be adjusted to accommodate different viewing heights, and it features a sturdy base with wheels for easy mobility.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents