Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Made in Vietnam - r03 Page 1 of 6
shake
TALL CHEST
Thank you for purchasing the Shake Tall Chest. This
page lists all the contents included in the box. Please take
the time to identify the hardware as well as the individual
components to this product. As you unpack and prepare
for assembly, place the contents on a carpeted or padded
area to protect them from damage.
Note: 2 people are recommended to safely assemble this product.
components
assembly hardware
mounting hardware
tools required
4 - plastic
anchors
4 - small
screws
4 - large
screws
4 - mounting
brackets
2 - wall
straps
Missing hardware? Please call 800.606.6387 for replacements.
phillips head screwdriver
(We recommend the use of hand tools instead of power tools)
1 - top panel
1 - center panel
4 - drawer fronts
1 - back panel
1 - bottom panel
2 - side panels
(1 left, 1 right)
4 - drawer bottoms
12 - wood
dowels
12 - bolts 32 - screws
8 - drawer sides
(4 left, 4 right)
4 - drawer backs
3
1 2
Insert 2 wood dowels into left and right side
panels as shown.
Insert 4 wood dowels into top and bottom panel.
shake
TALL CHEST
Made in Vietnam - r03 Page 2 of 6
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
bottom
panel
left and right
side panels
top
panel
With assistance of another adult, fit dowels of left and right
side panels into corresponding holes of center panel and
attach with 4 bolts. Secure, but do not over tighten, bolts
with a phillips head screwdriver.
left side
panel
right side
panel
Note: Do not over
tighten the bolts
center
panel
5 6
With assistance, position unit upright. Insert back
panel into corresponding grooves of assembly.
Fit dowels of top panel into corresponding holes of
assembly and attach with 4 bolts.
Fit dowels of bottom panel into corresponding
holes of assembly and attach with 4 bolts.
4
shake
TALL CHEST
Made in Vietnam - r03 Page 3 of 6
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
bottom
panel
back
panel
top
panel
9 10
Attach drawer back to left drawer side with 2
screws.
Attach right drawer side to drawer assembly with
4 screws.
Repeat steps 7-10 for remaining drawers.
7 8
Attach left drawer side to drawer front with 2
screws. Secure, but do not over tighten, screws
with a screwdriver.
Fit drawer bottom into corresponding grooves of
drawer assembly.
shake
TALL CHEST
Made in Vietnam - r03 Page 4 of 6
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
drawer front
left drawer
side
drawer
bottom
drawer
back
right drawer
side
11
Fit drawer glides of each drawer into
corresponding drawer glides of case assembly.
Make sure drawer glides securely engage.
Assembly is now complete.
shake
TALL CHEST
Made in Vietnam - r03 Page 5 of 6
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
drawer
assembly
cleaning and care
Clean surfaces with a dry or damp soft cloth. Do not
use abrasive cleaners.
NOTE: Make sure glides are pulled
out of the case and ball bearings are
at the front of the extended glides.
To prevent damage to glides, keep drawer
assembly level during installation.
For added safety and stability, it is recommended that the wall mounting hardware be installed. For safe
mounting, it is essential to use wall anchors appropriate to your wall type (i.e. plaster, drywall, concrete, etc.).
Mount to wood studs whenever possible.
NOTE: If you are unsure about your wall type or what mounting method you should use, consult a
qualified professional or your local hardware store.
A. Attach 2 brackets to the top of the assembled unit with 2 small screws per bracket.
B. With the assistance of another adult, place the unit in desired location against the wall. Mark the
location of the hole in the bracket on the wall. Move the unit out of the workspace.
C. Drill holes slightly smaller in diameter than the anchors. Insert 1 plastic anchor into each hole until
they are flush to the wall.
D. Insert 2 large screws through each bracket and plastic anchor. Secure, but do not over tighten
with a phillips head screwdriver.
E. Place the unit back into position against the wall and thread the wall strap through both brackets
and pull until tight.
Wall mounting assembly is now complete.
optional wall mounting instructions
shake
TALL CHEST
Made in Vietnam - r03 Page 6 of 6
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
A
C
D
E
/
