Made in Vietnam - r04 Page 1 of 6
veer WARDROBE
assembly hardware
wall mounting hardware
components
tools required
Thank you for purchasing the Veer Wardrobe. This page
lists all the contents included in the box. Please take the
time
to identify the hardware as well as the individual
components
to this product. As you unpack and prepare
for assembly, place the contents on a carpeted or padded
area to protect them from damage.
Note: 2 people are required to safely assemble this product.
Missing hardware? Please call 800.606.6387 for replacements.
(We recommend the use of hand tools instead of power tools)
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
phillips head screwdriverallen wrench (included)
28 - wood
dowels
8 - cams 8 - cam
screws
12 - small
bolts
8 - large
bolts
4 - pull
bolts
12- medium
bolts
12 - small
flat washers
12 - small
spring washers
20 - large
flat washers
20 - large
spring washers
16 - drawer
screws
4 - bolt
caps
7 - back
screws
16 - shelf
supports
36 - hinge
screws
6 - hinges
4 - plastic
anchors
4 - large
screws
4 - small
screws
2 - wall
straps
4 - mounting
brackets
1 - top panel 1 - bottom panel
2 - top fixed
shelves
1 - back panel
2 - pulls
2 - side panels
(1 right, 1 left)
2 - doors
(1 right, 1 left)
2 - bottom fixed
shelves
1 - partition
1 - rod 4 - legs4 - adjustable
shelves
2 - drawer
backs
4 - drawer sides
(2 right, 2 left)
2 - drawer
fronts
2 - drawer
bottoms
veer WARDROBE
Made in Vietnam - r04 Page 2 of 6
1
2
A. Insert 4 cams into 2 bottom fixed shelves as
shown. Make sure arrows on each cam points
towards nearest edge with holes.
B. Insert 8 wood dowels and 2 cam screws into
partition as shown. Secure, but do not over
tighten, cam screws with a phillips head
screwdriver.
3
A. Fit dowels of right side panel
into corresponding holes of 1 top
and bottom fixed shelves as
shown. Using a screwdriver,
attach top shelf to right side
panel with 2 small bolts, 2 small
spring washers and 2 small flat
washers.
B. Attach bottom shelf to left
side panel, by turning each cam
clockwise until it securely
engages the cam screw.
Repeat steps 3A and 3B for
partition.
NOTE: Do not
over tighten
the cam screws
Insert 8 wood dowels and 2 cam screws into
right and left side panels as shown.
partition
right side panel
right side
panel
partition
top fixed
shelf
bottom fixed
shelf
bottom fixed
shelf
small flat washer
small spring washer
NOTE: Do not
over tighten
the bolts
NOTE: Position
bracket for rod down
when inserting hardware
NOTE: Make sure the
bracket for the rod faces
away from right side panel
during assembly
left side panel
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
NOTE: Make sure arrows on
each cam points towards
nearest edge with holes
A
B
A
A
B
veer WARDROBE
Made in Vietnam - r04 Page 3 of 6
4
5
6
A. Fit bottom panel onto dowels of assembly as
shown. Attach bottom panel to side panels with 6
medium bolts, 6 large spring washers and 6
large flat washers, using an allen wrench.
B. Attach bottom panel to partition with 2 small
bolts, 2 small spring washers and 2 small flat
washers as shown, using a screwdriver.
A. Fit back panel into corresponding grooves of
side panels as shown.
B. Attach 4 legs to bottom of assembly with 2
large bolts, 2 large spring washers and 2 large
flat washers per leg, using an allen wrench.
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
NOTE: Make sure grooves
in side panels are facing
each other and positioned
as shown
A. Insert 4 wood dowels and 4 cam screws into
partition as shown.
B. Fit dowels of partition into corresponding holes of
remaining top and bottom fixed shelves. Attach top shelf to
partition with 2 small bolts, 2 small spring washers and 2
small flat washers. Secure cams in bottom shelf to
partition.
Repeat steps 4A and 4B for left side panel.
small flat washer
small spring washer
B
left side
panel
partition
top fixed
shelf
bottom
fixed
shelf
B
A
A
small flat washer
small spring
washer
large flat washer
large spring
washer
A
A
B
B
B
A
back panel
B
NOTE: Make sure the
brackets for the rod are
facing each other and
positioned towards the
top of assembly
large flat washer
large spring
washer
7
8
9
10
veer WARDROBE
Made in Vietnam - r04 Page 4 of 6
With assistance of another adult, position unit
upright and secure back panel with 7 back
screws as shown, using a screwdriver.
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
top panel
A. Fit top panel onto dowels of assembly as
shown. Attach top panel to assembly with 6
medium bolts, 6 large spring washers and 6
large flat washers, using an allen wrench.
B. Attach top panel to partition with 2 small bolts,
2 small spring washers and 2 small flat washers,
using a screwdriver.
A. Using a screwdriver, attach 3 hinges to left
and right doors with 2 hinge screws per hinge
as shown.
B. Attach hinges of left and right doors to side
panels with 4 hinge screws per hinge as shown.
NOTE: Reference diagram
for adjusting hinges at the
end of these instructions
right and
left doors
pull
Attach 1 pull to right and left doors with 2 bolt
caps and 2 pull bolts as shown, using an allen
wrench.
NOTE: Do not
over tighten the
screws
A
B
A
B
A
B
A
B
11 12
13
veer WARDROBE
Made in Vietnam - r04 Page 5 of 6
A. Place 2 drawers into bottom shelves of
assembly.
B. Place 4 adjustable shelves into assembly.
Make sure each shelf is securely supported by
shelf supports.
C. Fit rod onto brackets of left side panel and
partition. Assembly is now complete.
rod
adjustable
shelf
drawer
cleaning & care
Clean surfaces with a dry or damp soft cloth. Do not use abrasive
cleaners. Do not use furniture wax or polish as the unit is finished with
a protective clear lacquer.
A
C
B
A. Attach left drawer side to drawer front and
drawer back with 4 drawer screws, using a
screwdriver.
B. Fit drawer bottom into grooves of drawer
front/back.
C. Attach right drawer side to drawer front/back
with 4 drawer screws.
Repeat steps 11A-C for remaining drawer assembly.
Insert 16 shelf supports into assembly at desired
shelf heights as shown. Press firmly to secure.
A
B
C
drawer
back
drawer
front
drawer
bottom
drawer
left
drawer
right
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
hinge adjustment
If the doors do not appear square or aligned,loosen or tighten the
appropriate screws on each case hinge as illustrated.
Depth adjustment:
Loosen screw A, push hinge arm
forwards or backwards, re-tighten
screw A and secure screw B with
a 1/4 turn clockwise
Height adjustment:
Loosen screw C, adjust door
height and re-tighten screw C
A
B
1
2
3
Side to side adjustment:
Loosen screw A, adjust gap with
screw B and re-tighten screw A
A
C
C
B
veer WARDROBE
Made in Vietnam - r04 Page 6 of 6
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
A
C
D
NOTE: If you are unsure about your wall type or what mounting method you should use, consult a
qualified professional or your local hardware store.
For added safety and stability, it is recommended that the wall mounting hardware be installed. For safe
mounting, it is essential to use wall anchors appropriate to your wall type (i.e. plaster, drywall, concrete,
etc.). Mount to wood studs whenever possible.
A) Attach 2 mounting brackets to top of unit using 2 small screws per bracket.
B) Determine the final location of unit. Mark position on the wall, approximately 2" below each
mounting bracket on the back of the unit.
C) Drill a hole in the wall stud. If a wall stud is not available, drill a hole in the wall that is slightly smaller
in diameter than the anchor. Gently tap the plastic anchor until the flange of the anchor is flush with the
wall.
D) Attach the mounting brackets to the wall by inserting 2 large screws through each mounting
bracket and into the wall anchor in the wall.
E) Position the unit so the mounting brackets on the back of the unit are aligned with the wall brackets.
F) Lace one end of each wall strap through corresponding brackets, and into the other end of the strap.
G) Pull the straps tightly until secure.
Wall mounting assembly is now complete.
optional wall mounting assembly
WALL
F
-
1
-
2
-
3
-
4
-
5
-
6
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI