Barco Galaxy NW-7 EX Installation guide
- Category
- Projectors
- Type
- Installation guide
DVI HDCP Input Kit
Installation manual
iCon H250/ H500, iD H250/H 500, NH-12, Ga laxy NH-12
R9843045
R59770246/01
30/10/2008
Barco nv Presentations
Noordlaan 5, 8520 Kuurne
Phone: +32 56.36.82.11
Fax: +32 56.35.86.51
E-mail: [email protected]
Visit us at the web: www.barco.com
Printed in Belgium
Federal Communications Commission (FCC Statement)
This equipment h as been tested and found to comply with the limits for a class A digital device, pursuan t to Part 15 of the FC C rules.
These limits are designed to provide r easonable protection aga inst harmful interference when the equipm ent is operated in a com m ercial
environment. This equ ipment generates, uses, and can radiate radio frequency energy and, if not installed and used in a ccordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may
cause harm ful interference, in which case the user will be responsible for correcting any interference at his own e xpense
Copyright ©
All rights reserved. No p art of this documen t may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or
stored in a retrieval system without the prior written con sent of Barco.
Changes
Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied w ar-
ranties or m erchantability and fitness for a particular purpose. Barco m ay make improvements an
d/or changes to the product(s) and/or the
program(s) described in this publication at any time without notice.
This pub lication could contain technical inaccuracies or typographical e rrors. Changes are periodically m ade to the information in this
publication; these changes are incorporated in new editions of this publication.
Guaran tee and Compensation
Barco provides a guarantee relating to perfect man ufacturing as part of the legally stipulated terms of guarantee. O n receipt, the pu rchaser
must immediately inspect a ll delivered goods for dam age incurred during transport, a s well as for material and manufacturing faults Barco
must be informed immediately in writing of any complaints.
The period of gu arantee begins on the date of transfer of risks, in the c ase of special systems and software on the date of comm issioning,
at latest 30 days after the transfer of risks. In the event of justified notice of com plaint, Barco can repair the fault or provide a replacement
at its own discretion within an appropriate period. If this m easure proves to be impossible or unsuccessful, the purchaser ca n demand a
reduction in the purchase price or c ancellation of the contract. All other claim s, in particular those relating to com pensa tion for direct or
indirect damage, and also damage attributed to the operation of s oftware as well as to other services provided by Barco, being a component
of the system or independent service, will be deemed invalid provided the dam age is n ot pro ven to be attributed to the absence of properties
guaranteed in writing or due to the intent or gro ss negligence or part of Barco.
If the pur chaser or a third party carries out m odifications
or repairs o n go ods delivered by B arco, or if the goods are ha ndled incorrectly,
in particular if the systems are commissioned operated incorrectly or if, after the transfer of risks, the goo ds are subject to influences not
agreed upon in the contract, all guarantee claims of the purchaser will be r endered invalid. N ot inc luded in the guarantee cove rage a re
system failures which are attributed to programs or s
pecial electronic c ircuitry provided by the purchaser, e.g. interfaces. Normal wear as
well as norm al maintenance are not subjec t to t he guarantee provided by Bar co either.
The environmental conditions as well as the servicing and m aintenance reg ulations specified in the this m anual m ust be com plied with by
the customer.
Table of contents
TABLE OF CON TENTS
1. Safety................................................................................................................. 3
1.1 Safety warnings....................................................................................................................... 3
2. Introduction ......................................................................................................... 5
2.1 DVI HDCP input board ............................................................................................................... 5
2.2 DVI HDCP input board Kit. ........................................................................................................... 5
2.3 Assembling the DVI HDCP input bo ard. . . . . ......................................................................................... 6
3. Installation in the NH-12 and in the Galaxy NH-12............................................................ 9
3.1 Installing an optional input layer . .................................................................................................... 9
4. Installation in the iCon H250/H400/H500 and in the iD H250/H500 .......................................13
4.1 Removing the PMP..................................................................................................................13
4.2 Removing the input module ......................................................................................................... 15
4.3 Replacing the DVI / D15 input....................................................................................................... 16
4.4 Installing the DVI HDCP input layer .................................................................................................17
Index......................................................................................................................19
R59770246 DVI HDCP INPUT KIT 30/10/2008 1
Table of contents
2 R59770246 DVI HDCP INPUT KIT 30/10/2008
1. Safety
1. SAFETY
1.1 Safety warnings
WARNING: This p rocedure is intended for use only by BARCO authorized technicians.
WARNING: Be sure that the p rojector is powered dow n an d that the power cord is removed from the w all
outle t.
Wait until the projector is cooled down before starting the procedure.
CAUTION: Wear a wrist band which is connected to the ground w hile handling the electrostatic discharge
sensitive parts.
R59770246 DVI HDCP INPUT KIT 30/10/2008 3
1. Safety
4 R59770246 DVI HDCP INPUT KIT 30/10/2008
2. Introduction
2. INTRODUCTION
Overview
• DVI HD CP input board
• DVI HDCP input board Kit
• Assembling the DVI H DCP input board
2.1 DVI HDCP input board
Introduction
The DVI HDCP input board allows the input of DVI single link sources to the p rojector and implements the High-Bandwidth Digital
Content Protection.
The boa rd can be mounted in a free slot of the p rojector ’s input module (NH-12; Galax y NH-12) or will replace the existing DVI input
board (iCon H250/H400/H500; iD H2 50/H500).
The signal of a source connected to the DVI HDCP input board will not be displayed on the DV I output.
Software
The software of the projector automatically detects the new input board at first start-up and implements it in the source selection
menu.
2.2 DVI HDCP input board Kit
In iCo n an d iD p rojectors, this upgrade kit can not be u sed in co mb ination with the SD I/HDSDI upgrad e kit
R9843047.
In iCon and iD projectors, this upgrade kit is n ot applicable o n the following projectors: R9210 500, R9210510,
R9210520 and R921070, which are projectors with o pt
ion S DI/HDSDI.
Kit description
The kit contains the following items
Description
Qty
Image
DVI HDCP input board
1 image 2-1
fixation nut 2 image 2-4
bottom screw 1 image 2-5
front bolt 4 image 2-3
front plate ( NH-12; Galaxy NH-12) 1 image 2-2
side screw 2 image 2-6
packaging 1
-
R59770246 DVI HDCP INPUT KIT 30/10/2008 5
2. Introduction
Image 2-1
DVI HDCP input board
Image 2-2
Front plate (NH-12; Galaxy NH-12)
Image 2-3
Front bolt
Image 2-4
Fixation nut
Image 2-5
Bottom screw
Image 2-6
Side screw
2.3 Assembling the DVI HDCP input board
Necessary tools
Torx screwdriver T10
How to assemble the DVI HDCP input board?
1. Fix the fixation nut to the input board using the bottom screw
6
R59770246 DVI HDCP INPUT KIT 30/10/2008
2. Introduction
Image 2-7
Tip: Do not fix the front plate to the DVI HDCP input board yet!
R59770246 DVI HDCP INPUT KIT 30/10/2008
7
2. Introduction
8 R59770246 DVI HDCP INPUT KIT 30/10/2008
3. Installation in the NH-12 and in the Galaxy NH-12
3. INSTALLATION IN THE N H-12 AND IN THE GALAXY
NH-12
In the Galaxy NH-12 the DVI HDCP input board will be mounted in the free slot. In the NH-12 the DVI HDCP
input board can be mounted in one free slot or the other. The procedure is exactly an alog for both free slots.
3.1 Installing an optional input layer
The procedure b elow describes how to ins tall the optional input board in the t op slot, but the proced ure to
install it in the other free slot is equal.
Necessary tools
• Torx screwdriver T10
• Nut sp anner 5 mm
How to install the optional input layer?
1. Remove the covers (see c oncerning chapters)
- rea r cover
- front cover
2. If there is a blank cov er plate present, remove it by unscrewing both fixing screws
Image 3-1
Optional input layer: fixing screws of the blank c
over plate
Image 3-2
Optional input layer: fixing screws of the blank cover plate
R59770246 DVI HDCP INPUT KIT 30/10/2008 9
3. Installation in the NH-12 and in the Galaxy NH-12
Image 3-3
Optional input layer: cover removed
3. Insert the optional input layer in the input module
4. Push the optional input board to the left side to plug in the board-to-board connec tors to the PMP
Image 3-4
PMP: board-to-board connectors for optional input board
Image 3-5
Optional input layer: plug in the board-to-board connectors
5. Fix the optional input layer to the PMP us ing a fixing screw
Image 3-6
Optional input layer: fixing side screw
Note: This screw can be reached from the left side of the projector without taking out the input module
6. Fix the front panel to the o pti
onal input layer us ing the front bolts
10
R59770246 DVI HDCP INPUT KIT 30/10/2008
3. Installation in the NH-12 and in the Galaxy NH-12
Image 3-7
7. Fix the front panel to the input m odule using the fixation screws
Image 3-8
Position of the fixing screws
8. Install the covers (see concerning chapters)
- front cover
- rea r cover
R59770246 DVI HDCP INPUT KIT 30/10/2008
11
3. Installation in the NH-12 and in the Galaxy NH-12
12 R59770246 DVI HDCP INPUT KIT 30/10/2008
4. Installation in the iCon H250/H400/H500 and in the iD H250/H500
4. IN STA LL ATI ON IN THE I CON H25 0/H400/H500 AND
IN THE ID H25 0/H500
The software version of the p rojectors must be 1.30 or higher. Lower versions do not support this DVI HDCP
input board!
The iCon H400 is replaced by the iCon H500 and will not be mentioned in the procedure. The procedure below
is valid for both models.
In this projector models, the DV I HDCP input board must be put in the place of the ’old’ DVI input board!
Overview
• Removing the PMP
• Removing the input module
• Replacing the DVI / D15 input
• Installing the D V I H D C P input layer
4.1 Removing the PMP
To install this input upgrade kit, it is not necessary to completely remove the PMP. The input module can be
made accessible b y disconnecting t he PMP partially and just flippi
ng it over.
Necessary tools
• Torx screwdriver T10
• Nut sp anner 5 mm
How to flip over the PMP?
1. Remove the front screw, fixing the upper part of the front panel to the input m odule
Image 4-1
iCon and iD H250/H500: fixing screw of the front plate upper part
2. Remove the 6 bolts, fixing the upper part of the front panel to the PMP
R59770246 DVI HDCP INPUT KIT 30/10/2008
13
4. Installation in the iCon H250/H400/H500 and in the iD H250/H500
Image 4-2
iCon and iD H250/H500: fixing bolts of the front plate upper part
3. Remove the upper part of the front panel
4. Unplug connector J 110 (cable coming from the SBC) — O NLY FOR ICON H250/H500
Image 4-3
iCon H250/H500 ONLY: unplug connector J110 on the PMP
5. Remove both fixing screws
Image 4-4
iCon H250/H500: PMP fixing screws
Image 4-5
iD H250/H500: PMP fixing screws
6. Disconnect the PMP from the backplane, by lifting it
7. Flip over the PMP, in order to get access to the input modu le
14
R59770246 DVI HDCP INPUT KIT 30/10/2008
4. Installation in the iCon H250/H400/H500 and in the iD H250/H500
Image 4-6
PMP flipped over
4.2 Removing the input module
Necessary tools
Phillips screwdriver Ph1 — long model
How to remove the input module?
1. Remove the pixel map processor (PM P) — Se e the concerning chapter.
2. Loosen the two screws fixing the input module (use a long screwdriver).
Image 4-7
Fixing screws of the input box
3. Slightly lift the input m odule and disconnect the power connector
- J419 (6 wires): power from the power box (co
nnector 6)
Image 4-8
4. Lift the input m odule to remov e it
R59770246 DVI HDCP INPUT KIT 30/10/2008
15
4. Installation in the iCon H250/H400/H500 and in the iD H250/H500
4.3 Replacing the DVI / D15 input
Necessary tools
• Screwdriver Torx T10
• nut spa nner 5 mm
How to replace the DVI / D15 input?
1. Remove the input module — S ee t he concerning chapter.
2. Remove the side screw
Image 4-9
Side screw fixing the DVI / D15 input
3. Remove the front nuts
Image 4-10
Front nuts fixing the DVI /D15 input
4. Remove the backplane by pulling it off
16
R59770246 DVI HDCP INPUT KIT 30/10/2008
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
Barco Galaxy NW-7 EX Installation guide
- Category
- Projectors
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Barco iCon H250 Installation guide
-
Barco iD H500 User manual
-
Barco HD-SDI input board for iCon Installation guide
-
-
Barco 72 Rear Projection System for iQ Pro Series Installation guide
-
Barco Audio switching and video input kit for iD series Installation guide
-
-
Barco Galaxy NW-12 User manual
-
-
Other documents
-
König CSFCGALS5MBL Datasheet
-
-
Extron PMP Series User manual
-
-
Samsung J110 Galaxy J1 Ace Hard reset manual
-
Ruckus Wireless ZoneFlex H500 Quick Setup Manual
-
Tektronix H500 User manual
-
Toshiba SD-H400-S-TU User guide
-
Trendnet TV-H400 Quick Installation Guide
-
HoistFitness H-400 Owner's manual
