i3 International Veo17 Quick start guide

Brand: i3 International

Model: Veo17

Type: Quick start guide

CANADA 780 Birchmount Road,

Unit 16, Toronto,

ON, M1K 5H4

U.S.A 4450 Witmer Industrial Estates

Unit 4 Niagara Falls,

NY 14305

www.i3international.com

1.866.840.0004

Rev. 161207

Quick Installation Guide

Veo17 Embedded DVR

SAFETY

When installing your Veo17 Embedded DVR be sure to avoid:

• excessive heat, such as direct sunlight or heating appliances

• Contaminants such as dust and smoke

• Strong magnetic fields

• Sources of powerful electromagnetic radiation such as radios or TV transmitters

• Moisture and humidity

• Areas with mechanical vibrations

• Temperatures below -10°C (14°F) and above 55°C (131°F)

POWER SUPPLY

Veo17 Power consumption requirement: 12V DC, max 30W (without Hard Drives).

PACKAGE CONTENTS

In addition to this Quick Installation Guide and the Veo17 DVR, the packing box includes:

1. Rackmount brackets (x2)

2. SATA flat cables (x2) (May be Pre-installed in system with Hard Drives)

3. HDD Power cable (x1) (May be Pre-installed in system with Hard Drives)

4. Round-head screw, silver (x8) used to attach the HDD to the inside of the device. (May

be Pre-installed in system with Hard Drives)

5. 12V DC Power Supply

6. Power Cable

7. Cat 5 Network Cable

8. USB mouse

The Veo17 is in compliance with UL, FCC, and CE requirements.

No. Item Description

1 VIDEO IN 16 x BNC connectors for HDTVI & analog video input

2 USB Port Universal Serial Bus (USB) for mouse connection

3 HDMI HDMI video output connector

4 VGA DB15 connector for VGA output, display local video and

5 AUDIO IN Audio Input RCA connector

6 AUDIO OUT Audio Output RCA connector

7 Gigabit LAN/

Network Port

CAT5 network connection port

8 RS-485 Interface RS-485 PTZ control connector

9 12V Power Input 12V DC Power Supply connector (included)

10 Power Switch Power ON and OFF the DVR

11 GND Ground

Veo17

It may be necessary to add hard drives to Veo17. Follow these steps:

1. Ensure the Veo17 is disconnected from a power source.

2. Make sure you are properly grounded to prevent static electricity from damaging

the equipment.

3. Remove the cover from the DVR by unfastening the screws on the back and side.

4. Connect one end of the data cable to correct connector on the motherboard of the

DVR and the other end to the HDD.

5. Connect the power cable to the HDD.

6. Place the HDD on the bottom of the device and then fasten the screws on the

bottom to firmly attach the HDD to the bottom of the machine case.

7. Re-install the cover of the DVR and secure it by fastening the screws.

For more information please consult the Veo17 user manual.

HARD DRIVE INSTALLATION

Local Login: On startup the local log in screen will be displayed. Using the monitor and

mouse connected to the DVR use the on screen keyboard to log in.

Default login and password are i3admin / i3admin.

Remote Login: It is possible to use a networked computer to remotely access the

Veo17. To do so open the browser on the networked computer and enter the IP address

of the Veo17 machine into the address window. A login window will appear, enter the

username and password.

Default IP: 192.0.0.16

Default Username and Password: i3admin / i3admin

INSTALLATION

DVR PARTS AND DEFINITIONS

The Veo17 is built in a 1U chassis for convenient Rackmount installation. Follow safety

precautions when selecting an installation location for your Veo17 DVR.

1. If using the Rackmount option use existing screws from the chassis to secure the

provided Rackmount brackets to the Veo17 unit, then install the Veo17 DVR into the

server rack. Otherwise find a flat dry dust free surface to place the DVR on.

2. Make sure the Power switch is in the OFF position.

3. Plug the USB mouse into one of the two USB ports on the rear panel of the machine.

4. Plug in the monitor. Depending on the monitor model, use either the HDMI or the VGA

port on the back panel of the machine.

5. Connect the Analog cameras into the VIDEO IN BNC video ports #1-16. Note, that

i3-TVI cameras will have two coaxial cables: 720x480 (D1 quality) and 1MP/2MP

(780P/1080P quality). Make sure you connect the coaxial cable that transmits your

desired video quality.

6. Connect your video inputs PTZ signal cables (where applicable) to the RS-485 block

on the rear panel of the

DVR. Using a pointed

object, press and hold

the orange toggle

portion of the D+ and

D- RS-485 terminals

and insert the correct

PTZ signal cables into

the slots below. Release

the orange toggle to

secure the cables in

place. Ensure a secure and tight cable connection.

7. Connect your Audio IN and OUT devices, if using, to the corresponding RCA connectors

on the rear panel.

8. Plug in the network cable into the Gigabit LAN connector on the rear panel of the

Veo17 and then plug it into the Network.

9. Connect the provided 12V power supply to the 12V DC Power Supply connector and

then plug in the supplied Power Cable into the provided power supply.

10. Plug the power cable into the power source. Use of the UPS (Uninterrupted Power

Supply) is highly recommended by i3 for added reliability and longevity of your DVR.

11. Return the power switch into the ON position. The DVR will power on and the front

panel LEDs will turn on.

QR Code to Complete

User Manual

i3 International Veo17 Quick start guide

i3 International Veo17 Quick start guide

i3 International Veo17 Quick start guide

Related papers

Other documents